Laserfiche WebLink
File MH11766(Sp) Vol. 1 Sec. 2 Page 11 Issued: 1995-01-26 <br />and Report New: 2004-0q-2-48-11 <br />Form Number 857280 and 300020 -XXX Vacuum Sensor - FIG. 8 <br />General - Form Nos. 300020 -XXX vacuum sensors consist of from two•to <br />four Form No. 857280 -XXX vacuum sensors secured to a steel mounting <br />bracket, Item 9, by screws. <br />1. Enclosure - Constructed of R/C (QMFZ2) manufactured by GE Plastics, <br />Compound Designation Ultem CRS5111P4-& tie, shaped as shown in Ill. <br />69. <br />2. Printed Circuit Board — Not visible. R/C (ZPMV2), see ILLS. 70-734 <br />for schematics, componentltrace layouts and parts list. (Circuit <br />board contains a maximum capacitance of 35.74 gF including tolerance <br />and one inductor, maximum measured inductance is 333.77uH and the <br />nce is 3.9251) . Vie foll <br />be Drotective components <br />the <br />Protective Diodes (D8 -D10) - Rated 7.5V, 5W, 3W with forward current <br />(IE) of 200mA <br />Protective Diodes (D12 -D17) - Rated 7.5V, 5-*,*500mw <br />3. Solenoid valve - Mot visible. Manufactured by -Lee Company, Part No. <br />LHL.XOS00700B (maximum measured inductance 44.41ME at 1kHz, minimum <br />measured resistance 89.5751). Encansulated to a minimum depth of lmm <br />in an area of the enclosure as shown in Ill. 69 page 2. <br />yncaDsuiaticn material manufactured by Conap Potting Compound Part <br />No. MT -2541. Refer to I11. 73 for construction details.- valve beds <br />is constructed of R/C (QMFZ2) manufactured by GE Plastics, Compound <br />Designation Valox 830 and the valve gasket is constructed of Lee <br />Company Ccmncund LSTgDG208270 (C -FLT! <br />Cable Compression Fitting - Compression -type cable fitting with <br />synthetic rubber gland, manufacturer may vary. <br />5. Compression Fittings - Three <br />enclosure, Item I and one is <br />Consists of the following na <br />rovided, two are installed on the <br />nstalled on the riser, Item 10. <br />Body - Constructed of Dow Chemical material designated <br />Isoplast 101LGF, see ILL. 74 for details. <br />Gland - Synthetic rubber, manufactured by Precision Polymer, <br />Compound CPO -426 approx 17/32 in. long, 5/8 in. OD at the widest <br />end. 1/2 in. OD at the narrow end, 1/4 in. ID. <br />Nut - Constructed of same material as body, see ILL. 75 for details. <br />6. Tubing fittings - Two provided one elbow fitting and one tee <br />fitting. Manufactured by Eldon James Corp, Part No. LO-4GFBN (El <br />and TO-4GFBN (tee). Fittings are constructed of plastic material <br />manufactured by Entec, Compound N10OSTHLBK (Nylon 6-6). <br />File KH11766(So) Vol- 1 Sec. 2 Paqe 12 Issued: 1995-01-26 <br />