Laserfiche WebLink
�"UL/ULC LISTED SECONDARY CONTAINMENT FITMlGs <br />I <br />LI <br />TEE 900 ELBOW <br />k•'tirVi� �p" #f <br />B B <br />TERMINATION CONCENTRIC REDUCERV) <br />WITH 3/4" NPT <br />3/4" NPT <br />+ TAP <br />r �I - <br />Sizes available for Termination Concentric Reducers; <br />with and without tap: 3"x 2", 4"x 3", *6"x 4". <br />Sr2ES <br />450 ELBOW SLEEVE COUPLING <br />A <br />a <br />SADDLES _ <br />SIZES AVAILABLE <br />B*11*d side Ou" <br />. Th—d d std* Ouosi <br />d.r-0 <br />NPT Inremd Th ­d.154 <br />3"x2" <br />3"x1" ' <br />4" x 2" <br />3" x 11/." <br />4"x3" <br />3"x11/r" <br />• <br />4"x1" <br />80 It. <br />4" x 11h" <br />24.4 m <br />4" x 1112 <br />PRESSURE RATINGS <br />Size <br />A <br />B <br />90 <br />D <br />E <br />6"• <br />Size <br />t 1'Au <br />• <br />1C <br />80 It. <br />3.. <br />24.4 m <br />3" <br />6 <br />7 <br />14 <br />3 <br />21/2 <br />21/2 <br />4" <br />71/2 <br />8 <br />14 <br />3 <br />3 <br />21/2 <br />E:�9 <br />Average at 75° F <br />16 <br />4 <br />4 <br />3 <br />PRESSURE RATINGS <br />Size <br />pslg at <br />150° F- ` <br />3" <br />90 <br />4" _ <br />80 <br />6"• <br />t41 <br />TERMINATION x <br />CONCENTRIC REDUCE t <br />F <br />Minim um <br />­'Nominal*:Bending <br />D <br />s <br />'76* F/24* C <br />es r <br />50 It <br />f— <br />c 3 r: <br />• <br />E� <br />Bending Properties of RED THREAD II Pipe <br />- , r •- - <br />N 1. PHYSICALTROPERTIES- <br />Minim um <br />­'Nominal*:Bending <br />RedlueP)I' <br />Pipe Size <br />'76* F/24* C <br />at 75° F <br />50 It <br />2" <br />15.2 m <br />Tensile Strength —Axial at 150* F <br />80 It. <br />3.. <br />24.4 m <br />Compressive Strength — Axial at 75° F <br />100 fL <br />4" <br />30.5 m <br />- , r •- - <br />N 1. PHYSICALTROPERTIES- <br />;TYPICAL <br />Property <br />Value <br />'Value <br />Test Method <br />at 75° F <br />11,900 psi <br />82.05 MPa <br />ASTM D-2105 <br />Tensile Strength —Axial at 150* F <br />9,300 psi <br />64.12 MPa <br />Compressive Strength — Axial at 75° F <br />22,700 psi <br />156.51 MPA <br />ASTM D-695 <br />at 75° F <br />1.92 x 106 psi <br />1.32 x 104 MPa <br />ASTM D-2105 <br />Modulus of Elasticity in Tension at 150° F <br />1.70 x 106 psi <br />1.17 x 104 MPa <br />Ultimate Hoop Tensile Strength at Burst <br />Average at 75° F <br />44,000 psi <br />303.37 MPS <br />ASTM D-1599 <br />Long Term Hoop Strength at 75° F <br />9,140 psi <br />63.02 MPa <br />ASTM D-2992 <br />Cyclic Pressure (150 x 106 cycles) at 150° F <br />8,020 psi <br />55.30 MPa <br />Procedure A <br />Thermal Expansion Axial <br />1.09 x 10_1 in./in./°F <br />1.96 x 10-5 mm/mm/°C <br />AOSI-TM16-3 <br />2" 3" 4" pipe <br />Thermal Conductivity <br />° <br />2.9 BTU/(ft. )(hr.)( F/in.) <br />° <br />0.42 W/(m)( K) <br />AOSi-TM16-15 <br />I 2" 3" 4" pipe <br />Specific Gravity <br />1.85 <br />1.f15 <br />ASTM D-792 <br />Flow Factor <br />150 <br />150 <br />AOSI <br />Hazen -Williams Coefficient <br />(1) A 3"x 2" reducer bushing which is (2) Threaded connections (3) Sharper bends should be eliminated (4) Data not available at lime of (6) Pipe is manufactured in compliance <br />not UL/ULC Listed is available for must be made with a to avoid stress concentration which printing. with ASTM D-2996. Refer to general <br />use with the 4"x 3" termination Ilexible connector. would result in premature pipe failure specification sheet in catalog for the <br />concentric reducer. under pressure conditions. (5) Tests run on pipe samples. D-2996 designation code. <br />7 <br />