|
Daily Terminal Yard lection Checklist FEB 25 �u,J
<br />7emtina: �'l4 .
<br />NOTE Enter vt rf OK X ff cored ve action is necessary (i e , repair, replacernent, etc), or/ 11 does not apply (i e cot, idn't sump fillers due to no loads) Provlltb detbif dl cb , ive apns taicn
<br />in cowmen section iol!oYvng the checklist If a gauge reading is requested enter the reading ratter than a check mark
<br />MON TUE
<br />YdED
<br />IiiUR
<br />FPI ?'SAT 5UN — -
<br />�E� J
<br />p N
<br />D N
<br />D ND N D N f1'
<br />_
<br />yI�-
<br />r,. F'=-`�'
<br />� ��
<br />��_w.T� �•. � F?—L��tS_�' s.i115.� V.i•r..__. 4... �ti» - _ y.,"..,i"•,��u.�-_.�
<br />- - -�
<br />J' �
<br />Atwveground Plping and Flange Leaks - Vsua!lyinsp•ct for drips and leaks, partici.+arty at cannechon points
<br />I
<br />and flanges Visually inspec ! flange and blind baits Look for signs of damage and yr corrosion. Ensure there are
<br />E
<br />/
<br />i
<br />arrows showing now di'recti'on Ensure piping is clearty marked with product service (Refer to AP! 570, section
<br />5 12 for Piping Inspection Code APl 1637 for hlark'nglebeli'ng)
<br />f
<br />V
<br />Cathodic Protection System (where applicable) - Visually inspect to ensure the sysl_?m is operational; monthly,
<br />complete the separate cathodic protection inspection form.
<br />Motor Operated Valves [MOVs) Air teak • Listen forairleaks
<br />Piping Supports - Ensure supports are in good condition, sturdy; inspect for signs of fust or damage
<br />-
<br />f .•
<br />Automatic Gates - Ensure gates open and close property and all safety features (sensotloops, contact alarms,
<br />fights, sounds) work correctly Look for obvious signs of damage to gate operator, rotiers, chains, hydraulic
<br />_
<br />pumps
<br />Walkthrough Gates Ensure
<br />- gates are closed and locked and show no signs of damage or unauthorized entry
<br />t/
<br />Oft -site Drain Valves - Ensure valves ani dosed and locked when not to use and show no signs ofdamage
<br />Video Cameras - Ensure cameras ar a present and show no obvious signs of damage Check rrronitorInside to
<br />I
<br />.r
<br />I ✓
<br />lI
<br />ensure they aro woddng property, are in focus and are adjusted to provide maximum v,'awing
<br />Dike Walls - inspect walls for damage, points for potential leaks during spill (ez animal burmitis, cracks)
<br />-''
<br />-'
<br />i
<br />mss.
<br />/
<br />Fencetine - Visually Inspect thefenceJine for holes in fencing, saggingl broken barbed wire, gaps under fencing.
<br />Y
<br />vegelation growing into fencing, suspicious packagesrpeople near fencing, signs of unautholized entry
<br />Valves -Look for product leaks and drips, Ensure valves are in the correct posrhon and locked when not fn use v
<br />Ensure water draw and roof drain valves are closed and locked when not in use
<br />- _
<br />i
<br />/ t
<br />Manifold Area - Ensure there are no signs ofleaks, vatves that are not in use are closed and locked, product
<br />valva• labels are corms f
<br />'
<br />Sews and Locks - Ensure all seals andlocks are in place and shcw no signs of tampering
<br />Dock Security Checks • Walk length of dock ispecb'ng above and below, verity all gates are closed and locked
<br />y
<br />et allTtimes, dark buildings kept locked when dock unattended, check for hose leaks, check lighting at night
<br />f~ I/
<br />Pump Off Pumps • Visually Inspect for leaks Nsten for excessive or unusual nose when running. verify, air in
<br />shack pmssure gauges, verily valves locked
<br />- - L
<br />I tubncator,
<br />j } Teaks Look for s.'gns ofdnp arleaks Pay Abse attenbon to welds, seams, valves and nozzles
<br />/ I Tank Information Stenciling -Ensure firern
<br />diaond is present, not faded and correct Ensure stenciling is correct
<br />J Y J (product, levels of concem, valve identification)
<br />TagsiDecals - Update slorege tank in-service tagsrdeca!s (Ex Lasf time inspected. C!eanMg dates, Capacity
<br />etc.)
<br />Floating Suction Level indicator - Verity floating suction level indicetoris moving with product salesyreceiptl
<br />Tank Shelf - Visuallyinspect forbulges, dents orsigns ofcortosion.
<br />Tt Monitoring Well - Visually inspect to ensure well is free of water, product and vapors. T
<br />Rags - Ensure there aro no ragslabsorbent pads laying about
<br />Electrical Cabinets - Ensure all cabinets are tightened closed and locked
<br />Driver Restroom - Ensure cleanliness, check vandalism
<br />Drips and Spills - Look forevidence of product that could be a sign ofa leak and could be a slipping hazard
<br />i 78ke corrective action immediately
<br />Test Room - Ensure cleanliness, samples appropriately labeled and stored, ensure exhaust fens are ---�
<br />_Ale• operational; lack room as appropriate
<br />Trash - Remove all trash and debris, empty trash cans
<br />�J—
<br />Band Term ria!
<br />Last updated bar'
<br />
|