|
Maj,15 02 04:15p Elite Iv Contractors Inc 209461P942
<br />WELD*ON'
<br />2Q
<br />METEIACRIZIAIM A>DRESWE
<br />DATASSEET STRUCTURAL SERIES
<br />SS208, SS214, SS218
<br />DESCRIPTION
<br />IPS WELD -ONO SS200 Series methacrylate adhosives are two component, 10:1 mix ratio products for bonding
<br />composites, thermoplastics, metals and combinations thereof. Minimal surface preparation' 2 combined with choice of
<br />working times, provide reduced labor and production cycle time. These products are widely used for marine,
<br />transportation and general plastic bonding applications. Packaging options Include 490 ml cartridges and 5 or 50 gallon
<br />bulk containers for application with meter -mix dispensing equipment,
<br />PRODUCT HIGHLIGHTS
<br />BENEFITS
<br />Choice of 10, 20 and 38 minute open times Selection for a wide variety of applications
<br />l Minimal surface preparation"' Reduced labor cost and throughput tlmes
<br />Non -sag application characteristics Facilitates application on non -level surfaces
<br />• Excellent environmental resistance Permanent bonds in harsh operating environments
<br />0 Permanent toughness and high elongation Excellent fatigue, Impact and shock load resistance
<br />TYPICAL ADHESIVE CHARACTERISTICS @ 75' F (24° C)
<br />0." A AAk-4.- __ o 1CC —k lwa:..waw- "j— 1 I,,
<br />Color:
<br />Off white
<br />MIX ratio by volume:
<br />10
<br />Mix ratio by weight,
<br />7.64
<br />Viscosity, cps!
<br />170,000-220,000
<br />Density, grams/rill:
<br />0,96
<br />unit weight, Ib/gallon:
<br />8.00
<br />TYPICAL PHYSICAL PROPERTIES
<br />White Off -White
<br />1 i
<br />1 i
<br />70,000-180,000
<br />1.25 0.99
<br />10.40
<br />RECOMMENDED SUBSTRATES'
<br />Tensile strength psi (mpa) 2,000-2,500 (14-17) Acrylics Poiyester
<br />Maximum Tensile Elongation (I,/.) X200 PVC, ABS . Vinylester
<br />Modulus, psi -I (mpa) 60,000-75,000 (413-5 i1) Coated Metals Polyester Gelcoat
<br />Lap Shear strength' psi (mps) 2,400-2.800 (16.19) Aluminum2 Other Thermoplastics
<br />Service Temperature, °F (°C) -67 to 160 (-55 to 71) Steell
<br />Bonds are generaly rosistant to the ertects of heat, water and moisture, aquamas avirri els and most p vvwum rlydrocarbens. Includtmg gisoBne,
<br />motor oil and dime1 triol. Not r>"rommended for irnmeirlflon or long-term anosurn to concentrated acid! or bases. or aggressi orgarde V Isola 6ud1
<br />as toluene, ketones, cold ester.. uaer must determine the surlobtely of each adt"veforfix Inh+nded use and application.
<br />1, Moat thermopiaslin can be bonded wyh no surfxe preparation other than s dry wlpe or , k blow -off. It rnnlamrooron IS Naible OF SuspaCted, wipe
<br />With alcohol prior to bendlog- Poiyoie0ns, thomtoplas9c PoNes%rs, lfuomcarbon pinatks and other low surface energy plastica are generally not
<br />bondable. Testing Is roqui od on thermoset plastics hofauaa N the wldA varfattonn In cornppsfitons and ease of bonding. See Important notes it, b,
<br />Ind c m rew" side.
<br />2. Prii molal for bonding by removing all dust, leave ecaio, nil, mid otitar surface residue Includtrmg oil and 9maso. MP 100 Mabel PrMner should
<br />be used to prepare alummum and ilitainlow; steel for bonding. Refer to MP 100 data aheot for Inalnx:tions. For beat results, appy MP 100 Metal
<br />Printer directly to the rieatn alunmfrKml wrfaCe YA!hout abrading, For mnxlmutn bond stm gh on aMPI, Abrade Surface prior to bonding or before
<br />applying NIP 100 to Stainless Sleet. See ImportAnt notes a, b and c on rovorse cidn
<br />3, Modulus as meowed In the 8noax poitfon of the abassrsrrain carve.
<br />4. Lap Shear Strength of Aluminum to Aluminum bond based on ASTM D1002 mmoon.
<br />IPS Corp. PO (lox 1,2728. Resanrch Trtargr. park, NC 277M - tMW PW Lcorg-q m - Tog Free: 1-x77-I1PS C1Lt1E -FAX (919)r,98-2439 39200 Was
<br />p.2
<br />
|