Laserfiche WebLink
Eos Installation! - 0 <br /> ]► The 3 Inlet of the 99 LD 3000 allows the leak detector to be Installed in the discharge port of <br /> 3 -5 HP submersible pumps. The discharge of the 99 LD-3000 is 3" male thread; Height- 16.25 inches. Width - 7.86 <br /> inches.Weight-29 pounds; Can be installed by one person. Now with easy access to check valve for field replacement. <br /> The 99 LD-3000 is available with flange fittings instead of threads as part#99 LD-30001FL. <br /> Integrated In-Line Check Valve 1 Pressure Relief: Allows the leak detector to compensate for a defective <br /> submersible pump pressure relief or check valves that allow drain-back into tanks. The integrated pressure relief valve <br /> of the 99 LD-3000 will hold 30 PSI in the line by itself. <br /> One Way Poppet Flow Path! Isolates pump turbulence from line leak detection at pump start-up. The hardened <br /> stainless steel poppet does not dimensionally change due to thermal conditions encountered during station operation <br /> (precision metering change is insignificant down to-20 degrees F). <br /> Reverse Ratio Piston/Poppet Combination: The leak detector has a smaller diameter piston area than <br /> the poppet it is attached to. This allows the leak detector to stay in the fast fill position (3 GPM) to a higher pressure <br /> while compressing vapor pockets and stretching flexible line faster, resulting in fess time to full flow. <br /> Smaller Volume / Faster Response Piston Size: Results in one-fourth the volume of fuel to replace <br /> when in leak search and one-fourth the volume to return to the line when pump is turned off. This results in achieving <br /> faster full flow to dispensers and faster resets to detect leaks. <br /> Technical Specifications 99 LD-3000 <br /> Fuels: • Gasoline, 100%methanol*,100%ethanol*, up to 15%MTBE 7,86 <br /> • Any combination of the above <br /> #1 or#2 diesel,kerosene,Jet A*or JP-4*,AV Gas* 5. 56 <br /> and Biodiesel*(all blends). M 171, <br /> When used with Biodiesel,any alcohol fuel concentration above 20%,Jet A,JP-4,or <br /> AV Gas,order part#LD3-SSVS for stainless steel fittings and stainless steel vent <br /> tubing.For chemical applications other than those listed above,contact factory. <br /> Certified to meet EPA 3 GPH @ 10 PSI: <br /> • Rigid pipe up to 406 gal., 1171 ft.of 3"id. td.25 <br /> • Flexible pipe up to 96 gal.,260 ft.of 3"id. <br /> • Combination of Rigid and Flexible pipe up to 502 gal., 1431 ft.of 3"id. PORT <br /> A <br /> Construction: Forged steel body;Steel alloy; Forged steel threads. (PUMP PRESSURE) <br /> Cylinder Assembly: Anodized 6061-T6 Aluminum <br /> Internal Parts: Anodized 2011-T3 Aluminum, 6061-T6 Aluminum; <br /> Acetron GP;CDSM 1026 and DDM 1026 steel, 8 75 <br /> ST <br /> 17-4 stainless steel PORT <br /> 3MALE NPT B <br /> Seals: Low drag, stainless steel spring energized teflon seals (LIME PRESSURE) <br /> O Rings: U.L.Approved V9702-Vton Type B Fluorocarbon ,18 NPT <br /> TYPICAL <br /> Metering Pin and Poppet: 17-4 stainless steel <br /> Check Valve: Acetron GP,Viton F Seal 3' MALE NPT <br /> Pressure Relief: Stainless Steel,29 PSI pressure relief. This pressure is in <br /> addition to the pump pressure relief. <br /> Inlet: 3"mate Outlet: 3°male <br /> • Certified to handle 12+feet of head pressure. <br /> • Exceeds EPA specifications for 3 GPH @ 10 PSI hourly test. <br /> • Vent line must be unobstructed,leak tight and connected to headspace of tank,not to be subjected <br /> to pressure or vacuum. <br /> • Combination line check/pressure relief prevents drainage into the tank. <br /> VM1 Vaporless Manufacturing, Inc. Toll Free: 1-800-367-0185 <br /> 8700 East long Mesa !Drive Phone: (928) 775-5191 <br /> Prescott Valley, Arizona 86314 Fax: (928) 775-5309 <br /> 02108 Web Site: ww►w.vaporiess.com 9 Email: vmi@vaporiess.com <br />