INSTALL_2003 PLAN - Laserfiche WebLink

Home Browse Search

12" DIA. x 2'-0" CONC BURIED BASE (TYP.) 2" U -BOL (TYP.) - 2" DIA. - 90'_ GALVANIZED ELL 2" GALVANIZED SCH 40 VENT RISER AT 12' ABOVE GRADE (P/V VENT PER LOCAL CODE) 2" DIA. x 8'-0" GALVANIZED SCH 40 SUPPORTS 7'-0" ABOVE GRADE (TYP.) 1/8" x 4" x 18" UNI -STRUTS AT 3' AND 5' ABOVE GRADE - � 2" ERR GAS01_INE VENT SLOPE VENTS DOWN 1/8 " PER FT. TO TANKS (TYP. ALL LINES 2" DIA, MALE ADAPTER VENT RISER DETAIL NOT TO SCALE 2" GALV. STEEL VENT - 2" ELL SIPHON TO BE 2" PIPE & SUPPORT TANKS AT LOCATIONS 4" x 2" DOUBLE & 90' ELBOW REGULAR) TO BE PAINTED "SOFT WHITE' TITEFLEX PART NO. STEEL PLATE o VENT RISERS 1 2. 2" FIBERGLASS ENVIRON ISOLATION TUBE W/DONUT ENVIRON PART NO. PIPE W/3" SECONDARY CONTAINMENT PIPE 7-11 2" 2" GALV. 90 DPW PART NO. 523V-2253 , Iz N O GEODUCT FLEXIBLE CONDUIT WITH ALCOHOL BLEND FUELS. SLAVE 7-11 2" x 3/8" BUSHING FOR COPPER LINE GEOFLEX-D SUPPLY PIPING ENVIRON PART NO. e n TANK END CLAMPS 2" NIPPLE MiN 0 i/8 T. OR AMERON ELECTRICAL CONDUIT (TYP.) SEE NOTE 2" FIBERGLASS PIPE �+ PRODUCT LINE STEEL PIPE tO WRAP EXPOSED VENT RISER 12" BELOW CONCRETE WITH 3M CATHODIC PROTECTION 7tNAPE NOTE: PRIOR TO PAINFING, 2 ALL GALVANIZED METAL MUST BE PREPPED FREE-STANDING VENT DETAIL NOT DSCALE NOTES NOTE: ALL DISPENSERS ARE TO BE POSITIONED WITH UNLEADED ON THE LEFT OF THE "A" SIDE OF THE DISPENSER FACE. SIDE "A" OF DISPENSERS ARE TO ALWAYS FACE CLOSEST TO STORE FRONT. IF THE DISPENSERS ARE PERPENDICULAR TO THE STOREFRONT, THE "A" SIDE WILL BE POSITIONED TO THE RIGHT, LOOKING TOWARDS THE STORE. 6 MPD'S 1-10,000 & 1-15,000 GAL. (1) 2 H.P. STP 6 FILL STAGE II "Y" FROM TANK TO FIRST BLENDER DISPENSER WITH 1 1/2" VAPOR RECOVERY PRIMARY PRODUCT LINE, AND USE 1 1/2" PRIMARY PRODUCT UMP TANK LINE TO THE REST OF THE BLENDER DISPENSERS. NTERSTIC 1 2 NOTE: FOR HIGH VOLUME LOCATIONS USE 2-15,000 GALLON TANKS 2 r.0 OR AS AN ALTERNATIVE, USE 3- 15,000 GALLON TANKS. FG TANK MONITOR 1�ry 2."F 3,.F 1 �P �'11N. SCOP MIN. g G SUB -PUMP �/8 SFT F q COpE 1 1/2„ FG i UNLEADED 11ry 1 11 `l. SANK , Z •'P ,gam i FLEX CONNECTOR Y ' 1/2" (TYP.) ti Z., FG 1 2 PREMIUM TANK 8 TAfyks NOTE: T� OPPOSITE REVERSE SIDESIF OF ISLANDSLOCATED ON TOWARD F�BE �CSCOpf 1. VENT RISER TO EXTEND A MINIMUM OF 12' ABOVE GRADE WHEN LOCATED IN REMOTE AREA. 2. ALL STEEL PIPE & CLAMPS ABOVE GRADE PAINTED "SOFT WHITE". PIPING SCHEMATIC (SIX ISLAND 'MPD'S) PAINT FURNISHED BY 7 -ELEVEN TO THE CONTRACTOR. NOTE: SEE SITE PLAN FOR PUMP AND VENT LOCATIONS 6" THICK CONCRETE PAVING W/ #3'S ® 18" O.C. BOTH WAYS. APPLY CONCRETE SEALANT PER SPECS,-, VAPOR RECOVERY LINE FIBERGLASS PIPIN SECONDARY PIPING SPECIFIED FILL ELECTRICAL CONDUITS z_ N U1 W PRODUCT PIPING — \ iO PRIMARY PRODUCT LINE 6"-3/8" PEAGRAVEL BEDDING SECTION THRU PIPING TRENCH NOT TO SCALE NOTE: IF CONDUIT OR WATER NEEDS TO CROSS TRENCH IT SHOULD DO SO PERPENDICULAR TO PRODUCT PIPE. OSE S0A STORP Sroe S� F I d� NOTES: 1. ALL FITTINGS TO BE CONTAINED INSIDE RISER. 2. SLOPE TO TURBINE SIDE. 3. ENVIRON FLEXIBLE ENTRY BOOTS (PART NO. FEB -6300) AT SIPHON PENETRATIONS, WITH 3 X 2 RUBBER REDUCER B00T (ENVIRON N0. RRB-3030) ON SIPHON SIDE & A 3 X 2 RUBBER TEST REDUCER (ENVIRON NO. RTR-3020) ON THE STP SIDE, SIPHON DETAIL NOT TO SCALE NOTE: - 2" ELL SIPHON TO BE 2" UNION THEN NIPPLE TANKS AT LOCATIONS 4" x 2" DOUBLE & 90' ELBOW REGULAR) TAP BUSHING TITEFLEX PART NO. 110165-242-0180 7-11 2" FIBERGLASS ENVIRON ISOLATION TUBE W/DONUT ENVIRON PART NO. PIPE W/3" SECONDARY CONTAINMENT PIPE 7-11 2" ENVIRON BALL VALVE #BSV-2020 DPW PART NO. 523V-2253 OR EQUAL. MUST BE RATED FOR USE O GEODUCT FLEXIBLE CONDUIT WITH ALCOHOL BLEND FUELS. SLAVE 7-11 2" x 3/8" BUSHING FOR COPPER LINE GEOFLEX-D SUPPLY PIPING ENVIRON PART NO. GFP-2150 TANK END v 2" NIPPLE RED THREAD II OR AMERON ELECTRICAL CONDUIT 2" THREADED SEE NOTE 2" FIBERGLASS PIPE �+ PRODUCT LINE STEEL PIPE LI #3 BELOW G.C. / \ 3/8 " COPPER TO 12" MANHOLE ASSEMBLY DPW PART NO. 2" UNION THEN NIPPLE FUNCTIONAL ELEMENT OF O8 & 90' ELBOW SUBMERSIBLE NO, VEF-4432 2"x2"x2" TEE 2" NIPPLE GEOTECH MATERIAL SEE SPEC. SECT. III 4" x 2" DOUBLE TAP BUSHING II II I I SUB PUMP END II I I 2" THREADED STEEL PIPE d� NOTES: 1. ALL FITTINGS TO BE CONTAINED INSIDE RISER. 2. SLOPE TO TURBINE SIDE. 3. ENVIRON FLEXIBLE ENTRY BOOTS (PART NO. FEB -6300) AT SIPHON PENETRATIONS, WITH 3 X 2 RUBBER REDUCER B00T (ENVIRON N0. RRB-3030) ON SIPHON SIDE & A 3 X 2 RUBBER TEST REDUCER (ENVIRON NO. RTR-3020) ON THE STP SIDE, SIPHON DETAIL NOT TO SCALE NOTE: EQUIPMENT SCHEDULE SIPHON TO BE USED FOR MANIFOLDING OF TWO REGULAR 10,000 GALLON TANKS AT LOCATIONS WHERE THREE 10,000 GALLON TANKS ARE USED (1-10,000 PREMIUM & 2-10,000 REGULAR) NOTE: ALL SUMPS TO BE WATER TESTED NOTE: FOR VAPOR VAC INSTALLATION, STAGE II VAPOR RECOVERY LINE SHALL BE 2" FIBERGLASS PIPE WHEN THERE ARE TWO DISPENSERS OR LESS, AND 3" FIBERGLASS PIPE WHEN THERE ARE THREE DISPENSERS OR MORE. GENERAL NOTES 1. PIPING TO BE TESTED UNDER PRESSURE DURING BACKFILL PROCEDURE TO ASSURE NO BREACH IN SYSTEM - CHECK OFTEN DURING BACKFILL AND COMPACTION. 2. STAGE II VAPOR RECOVERY PIPING TO BE PRESSURE TESTED FOR DECAY AND BLOCKAGE PRIOR TO BACKFILLING. 3. PIPING TO BE CHECKED FOR CONTINUOUS SLOPE BACK TO THE TANKS. EQUIPMENT SCHEDULE ITEM DESCRIPTION MANUFACTURER, PART NO. FURN. BY OFLEX GQNNECT, V 1-112 X 18 M X MS TITEFLEX PART NO. 110165-242-0180 7-11 O ENVIRON ISOLATION TUBE W/DONUT ENVIRON PART NO. FIT -3530, ITR -3020 7-11 O 2" VAPOR VENT CAP (VAPOR VAC) DPW PART NO. 523V-2253 7-11 O GEODUCT FLEXIBLE CONDUIT ENVIRON PART NO. GDP -4500-1 7-11 4A GEOFLEX-D SUPPLY PIPING ENVIRON PART NO. GFP-2150 7-11 O 3" FIBERGLASS PIPE RED THREAD II OR AMERON G.C. O 2" FIBERGLASS PIPE RED THREAD II OR AMERON G.C. O7 12" MANHOLE ASSEMBLY DPW PART NO. 104FG-1200 7-11 O8 4" X 4" X 3" X 2" EXTRACTOR ENVIRON PART NO, VEF-4432 7-11 O9 GEOTECH MATERIAL SEE SPEC. SECT. III 2.2 7-11 NOTE: ALL SUMPS TO BE WATER TESTED NOTE: FOR VAPOR VAC INSTALLATION, STAGE II VAPOR RECOVERY LINE SHALL BE 2" FIBERGLASS PIPE WHEN THERE ARE TWO DISPENSERS OR LESS, AND 3" FIBERGLASS PIPE WHEN THERE ARE THREE DISPENSERS OR MORE. GENERAL NOTES 1. PIPING TO BE TESTED UNDER PRESSURE DURING BACKFILL PROCEDURE TO ASSURE NO BREACH IN SYSTEM - CHECK OFTEN DURING BACKFILL AND COMPACTION. 2. STAGE II VAPOR RECOVERY PIPING TO BE PRESSURE TESTED FOR DECAY AND BLOCKAGE PRIOR TO BACKFILLING. 3. PIPING TO BE CHECKED FOR CONTINUOUS SLOPE BACK TO THE TANKS.