Laserfiche WebLink
I. SERVICE <br /> Under normal circumstances -our new IIoffman unit, with Proper installation and mainte- <br /> Ilance, Nvill providc years of trouble free se"ViCe. `I'llis manual is your guide to safe and sound <br /> A,rpc•ratioII. <br /> I1. WARRANTY <br /> "7"'Serie+units are g;unrarlteed against defective material or tt•urkmansllip for it period of <br /> eighteen (18) months fruul elate Of siliPnu-lit or twelve (12) months from start-up, whichever <br /> c•onlcs 1 irst. f)rfertivi parts mvill be repaired or replaced F:O.B. Our factory at 11ciffillaW.s 0 <br />' tion within the %%'arrant)' period, 1)ruvided tile etPliprllellt is ill"tall" and operated in accord- <br /> anee with surd i <br /> il►struclions. Warr:ultics affecting mutors, starter and ether purchasetems <br /> ill be thusc its cffec•t by the 11lauLlfucturer cc,ricer lie d. 'I'll is %varranty is voided if repairs or <br />' alterations are made without Lloffnlun's siaecific Written aulhorizalion. <br /> III. PRELIMINARY PRECAUTIONS <br />' A. I1ECEIVINC "1'11 L•' UNIT <br /> The unit should be examined thoroughly upon receipt. Shafts of both unit and driver should <br /> turn freely, and nu apparent cracks, dents, or clefurrnations should be ullscrve d. Damage to <br /> eilller the unit ur its crating should be i....ne:diately noted on the f reign[ receipl. Purchaser <br />' should file damage c•laiuis with the respul►sible carrier and notify the clearest llofflnan repre- <br /> sentativelsales office in wrding. <br /> B. HANDLINC <br />' The unloading ane) handling;of the equipment is the buyer's responsibility, and should be su- <br /> pervised by experienced personnel. move the unit only by lif tiltg under the steel base. DO <br /> NoT lift by the shaf t or bear iug, housings. Be careful to avoid any building, twisting or distor- <br /> t tion of the base frame. <br /> C. S'CO1lACL' <br /> !f the unit will not be placed in operation for an extended period of tine (LIP to 90 days), <br /> Ie:lVC Unit on its shipping skids and: <br /> a. Place in a c•ie:ul, dry protected urea, covered to protect it from corrosion. <br /> b. liol ate:shaft by hand at bi-weekly' intervals to prevent beari;tg;"set <br /> For storage in excess of go clays, consult Hoffman for further instructions. <br /> IV. INS`T'ALLATION <br /> A. LOCATION <br /> The permanent installation site should be it clean location. Ample space should be provided <br /> un all sides to allow lubricating, servicing and repairing;when required. DO NOT locate the <br /> unit ill :ll, a\Cessively hot area lilliess till: motor h:ls been Clesigned for such sery ice and unit <br /> 1 bearings arc properly safeguarded. <br /> B. BASE <br /> 1�'llell llo special foundation is required, the unit should rest on a solid level flat surface, such <br /> that the dead \Vet{;llt Of the Ullit gall be supported. Shippingsklds should be removed alld resp- <br />' ient isolator pacts inserted under the base. hell pad must bear its proper share of the loud to <br /> Prevent distorsion of the base, potential vibration and subsequent damage. <br />' <br /> DO NOT l�oluor PRd <br /> 1. Bolt base down"hard." <br /> Isolator Sleeve <br /> '?. Install piping.vitllout isolator sleeves. (m <br /> t3. Install excessive .veig;ht on tllaclline flanges (fillers, silencer, etc.) <br /> 3 <br />