ARCHIVED REPORTS XR0000155 - Laserfiche WebLink

Home Browse Search

Across the Line Starting G-1 Across the Line Starting M_ Dwn C►.w T1 12 13 T1 T2 T, M'T7 S Clow Dwn J I I I r� J T\ 1 l4/5 T3 L I N E L I N E M•r— 'Tb 6 •T6 MAINTENANCE 1. INSPECTION Inspect motor at regular intervals. Keep motor clean and vent openings clear. 2. LUBRICATION a. Frame 143T-256T: Double sealed ball-bearing motors without grease fittings. TOSHI BA prelubricated seal bearings don't need relubrication.These ouarings are designed for average 100,000 hours opera- tion under standard conditions.(See Table 2.) b. Frame 284T-587UZ: Motors having pipe plugs or grease fittings in bearing brackets. Grease motors prior to startup.(See(able below.)It is necessary to reiubricate anti-triction bearing motors periodically,depand- inch an size and type of service. Table 2. Frequency of Relubrication NOTES: 1 . Remark *: We recommend SYNC HPM rNAMf TYPE Of SERV+CE changing bearing after these kANGE kANGE StANDAkp operations, but it not change- (tln, aa, uperanan) (24Ht1asy aperat.on) able, you can relubricate by 1431-2161 S Yeats 2 Yeats removing the seal, cleaning 36M 2ImTs-2ti6TS zlo aays 70 day, and refilling the bearing and 324TS-187USS Ih0 days So 0a11 1431-2'.+61 7 YeA,s 3 Yea„ the cavity with recommended ?mT-3261 4 yeas 11 yeas grease. law 364r-'s61T 390 days 13U days 2. For easy service (1 Hr/day 4U41-44711 270 mays 90 dAYs operation) multiply tabled Imus-1H7ur 210 BAYS 70 asYs value by 2. 1411-:1x.r 7 rears • 3 scars ' ?x41-3241 4 Yea., r 1 Yea„ 3. For very severe service (High l2m k,41_a471Z 3SK1 days 130 oars vibration, shock) 1/3 of tabled 1U:U5-5d7ur 270dAy] , Q.Y> value. 3. INSTRUCTIONS FOR LUBRICATING Replace one pipe on each end shield with grease fitting.Remove the other plug for grease relief.Be sure fittings are clean and free from dirt.Using a low-pressure grease gun pump in the recommended grease until newgrease appears at grease relief hole.Relub- rication inlervals is specified on page 7, table 2. After relubricating, allow motor to run for 10 minutes before replacing relief plugs. 4. RECOMMENDED GREASE Use the following greases or some equivalent lithium based greases unless a special grease is specified on the nameplate. MOBILUX v2 MOBIL OIL CO. BEACON 325 EXXON ALVANIA #2 SHELL OIL CO. CHEVRON SRI NO.2 STD.OIL CO.OF CALIF. WARRANTY Generally,TOSHIBA will correct at it's option,by repair or replacement(f.o.b.a TOSHIBA-AUTHORIZED SERVICE SHOP),any defect in material and workmanship when properly used for a period of one yearafter installation or 18 months after shipment.whichever comes first.TOSHIBA is not responsible for apparatus returned without proper authorization and identification,improper handling or storage, ' misapplication of the motor or the driven equipment.defects in the driven equipment ordevice,or improper circuit prolection.The mount of liability shall not exceed the purchase price of the product.In no event shall TOSHIBA have any liabilityfor commercial loss,claims for labor or consequential damges of any type. It is expressly agreed that Buyer's remedies expressed in this paragraph are Buyer's exclusive remedies. ' RENEWAL PARTS (1) Use only genuine TOSHIBA renewal parts. (2) When ordering,specify complete information(at least Model Number and Serial Number)of the motor.Specify quantity and des- ' tribe pari. (3) For information and service refer to the nearest TOSH113A INTERNATIONAL CORPORATION office. WARNING ' EXPLOSION-PROOF MOTORS are constructed to comply with the U/L Label Service Procedure Manual. Repairs of EXPLOSION-PROOF MOTORS must be made by the manufacturer or UL listed service center to maintain the UL Listing. ' FOR FURTHER INFORMATION CONTACT TOSHIBA INTERNATIONAL CORPORATION Industrial Equipment Division ' 0131 Yr LITTL F YORK Rn P0 RnY ,lnapr; H0L+0T,-,N TFyacn-+n