|
VI—2 Fabricator shall insure all scaffolding, ladders, and rather
<br />equipment is in proper operating condition. lard hats will be
<br />worn by all employees and Shell Representatives during steel
<br />erection. The public should not be allowed to enter the work
<br />area. All power tools shall be inspected prior to work and
<br />fabricator shall insure all such tools rare properly grounded.
<br />V1-3 All Structural Steel will hove one shop carat of red lead paint.
<br />(Refer to plans and spedificotions of specific structures for
<br />details.)
<br />VI All Structural Steel will be pre—engineered, predrilled,
<br />fabricated prior to being delivered to project site. Fabricator to
<br />erect oil structural steel unless otherwise noted.
<br />VII CA NTR° AN l LLW R
<br />V11— I RA
<br />General Contractor will furnish tared erect ail frornin , concrete
<br />forms, rough and finish woodwork, as shown on the drawings.
<br />Proper bracing will be installed where necessary and required.
<br />All wood forms are to be removed after concrete work has set.
<br />VII2RA IN iR
<br />(General Contractor)
<br />VII -2—o, Grade and Trademark: Required on each piece of lumber (or
<br />bundled stock). Use only the recognized official marks of the
<br />Association under whose rules the material is graded. Grade
<br />o'nd trademarks will not be required if each shipment is
<br />accompanied by certificate of inspection issued by the Bureau
<br />or the Association responsible for the writing of the gradin
<br />reales.
<br />101
<br />LJ
<br />U
<br />VII -2—b. Moisture content requirements:
<br />1. Framing lumber 2—inches Maximum 1574
<br />and less in thickness
<br />2, rds®-inches or less in width maximum 1
<br />® Finishlumber and millwork Maximum 1
<br />a
<br />VIIP F
<br />Grades and species of lumber and millwork will be as follows:-
<br />For fr in , lumber, use .. 1 Dense grade Southern Pine. For
<br />exterior exposed woodwook, use C and better grade Southern Pine
<br />or Douglas Fir. For interior wood work except beams, use C and
<br />better grade Southern Pine or White Pine.
<br />VII -4 T�
<br />Stock form lumber cared roof plywood to insure proper ventilation
<br />and drainage. Protect lumber and plywood from the elements.
<br />VII -5 W R
<br />Provide and install oil rough hardware and metal fastenings
<br />as shown on drawings, specified herein or required for proper
<br />installation of carpentry and millwork, Nails, Sikes, screws,
<br />bolts, and similar items will be of sizes and types to rigidly
<br />secure members in place, See the various headings hereinafter
<br />specified for specific sizes and type of rough hardware
<br />required.
<br />Vill R . K N
<br />(MODULAR LOGS. — Y FABRICATOR)
<br />(PRE-ENGINEERED BLDGS.OPTIONAL, REFER TO PROJECT
<br />SCOPE OF WORK)
<br />Vlll 1 ,
<br />All Roof Steel Decking, sheathing, insulation and flashing will
<br />be furnished and installed as shown on drawings and as specified
<br />herein by Fabricator, for modular buildings at Fabricators
<br />manufacturing facility.
<br />Roof installation of pre-engineered structures, refer to project
<br />scope of work regarding responsibility for furnishing and
<br />installation of finish roof surface.
<br />VIII—2 I T . �
<br />V111 2 a, All fleshings, counter flashings, gravel straps, gutter and
<br />downspouts will be furnished and installed as detailed on the
<br />Orowings by Fabricator unless otherwise rioted per scope of work
<br />of specific project, Refer to project scope of work,
<br />specifications and Shell drawings.
<br />IX F�IIl
<br />lX 1 C�:� e fA
<br />A complete systern of plumbing and piping will be provided and
<br />installed as shown on the drawings and as hereinafter specified,
<br />The General Contractor will do all necessory trenching and
<br />backfilling. Backfilling will be clean earth or, sand, free from
<br />cinders, large stones or wet clay. Contractor will obtain and
<br />pay for all permits, inspections, deposits. etc„ necessary for
<br />the work. All work will be dome in strict accordance with state
<br />and local codes, regulations, and ordinances. Any additional ,
<br />casts resulting from any deviations from the contract drawings
<br />and these specifications due to codes or other requirements
<br />ill be borne by Contractor.
<br />am
<br />f
<br />,Plumbing installed in modular buildinqs with floors will be
<br />installedPiping for fixtures will be in,o g
<br />suitableFabricator and be installed complete as shown on drawings with
<br />hot and cold water supply. Fixtures will be for public
<br />use as manufactured by American Standard, Kohler Company or
<br />approved equal. All exposed metal, piping in rest rooms will be
<br />chromium or nickel plated. Fabricator to provide a shutoff
<br />valve on water supply for each and every fixture. Fabricator to
<br />furnish and install plumbing fixtures and material as shown per
<br />Shell drawings and specifications.
<br />Install garden hose bibbs where shown on drawings, Where
<br />indicated on drawings or called for a Addenda, install 3/4"
<br />non—fee ze wall hydrants with brass castings and chrome ^Ioted
<br />face prates. When indicated in landscaped areas install A"
<br />non -freeze post hydrants with brass costings and housings.
<br />Burial depth to be belowlocal frost line.Note: all hos
<br />bibs specified for landscaped areas will be furnished an
<br />installed by General Contractor.
<br />F
<br />(Buildings)
<br />Floor drains in wash boys will be furnished & installed by
<br />General Contractor. These drains will be - circular
<br />or 18" square, light duty, cast iron frame are grating or to
<br />1-1/4" ongle frame with 8 anchor rods, all welded and o
<br />1 " x ,1 "_x 1" steel subway grating cover. Fabricator will
<br />furnish and install cat iron floor drains with 3.® caulked
<br />bottom outlet in modular buildings with floors as shown'per
<br />drawings. Sea Plot Plan for connection of floor to sewer.
<br />Roof drains must be directedaway from uil in perimeters.
<br />Refer to plot and gradeplans for detail.
<br />X TINV TI TIN A I lT N1N
<br />(MODULAR BUILDINGS Y FABRICATOR)
<br />(CONVERSIONS STRUCTURES DELIVERED AND ERECTED
<br />AT PROJECT SITE -GENERAL CONTRACTOR)
<br />X— 1NRA
<br />X -1-o. Unless otherwise noted on 'Equipment List°, Contractor to
<br />furnish oil Labor and material necessary to complete the entire
<br />installation of the heating units, air conditioning units or
<br />combined system, except as noted hereafter. Refer to fixture
<br />schedule, for specific system including , type and capacity.
<br />X -1-b. The system as shown on the drawing will be installed iri
<br />strict accordance with state and local ordinances and to the
<br />requirements of the applicable code of the National Fire
<br />Protection Association, and accepted first class commercial
<br />practice. Shell will obtain and pay for all required permits.
<br />Equipment will bear the underwriters label when the type of
<br />equipment is so listed.
<br />X -1—c. iring to heating system components will be by the licensed
<br />electrical contractor.
<br />f ITi
<br />The foregoing enerol clauses will apply, as will the pertinent
<br />sections of the above specifications for heating system. The
<br />installation will in general conform to the requirements of
<br />NFPA Standard 90A (Latestedition). Contractor will adjust and
<br />balance system under severe operating conditions and if it is a
<br />combine.0heating n cooling system, will post chop e—over
<br />instructions. Warranty documents and opera (ion/ointenonce
<br />manuals to be delivered to Owner (namely roc ct Engineer)
<br />upon final revi und acceptance of installed equipment.
<br />I A A
<br />Entire heating installation will be completely adjusted and
<br />tested after completion and left in a satisfactory operating
<br />condition' and owner be given by the contractor, o written
<br />manufactures guarantee covering oil material and workmanship
<br />against failure for a period of one year after acceptance.
<br />Refer to bldg. drawings and specifications for further details.
<br />Refer to building design drawings and specifications for
<br />details .
<br />X-5,
<br />Refer to building design drawings and specifications for
<br />details.
<br />X A T T R VRI FiP -NT
<br />Refer to building design drawings, specifications and Convience
<br />Store uipment Standards Manual for details.
<br />XI I N I A Ti
<br />XI_
<br />Properly install all equipment as shown on the attached
<br />"Equipment Schedule's in strict accordance with manufacturer's
<br />details which ore considered c port of these specificotions.
<br />Equipment will be tested and left in a clean' and satisfactory
<br />operating condition.
<br />The contractor will be responsible for 'the receipt, storage and
<br />security of all equipment furnished by Owner from the time a
<br />notice of delivery is received or the item is delivered to the
<br />job site until the final acceptance of the completed unite
<br />Any charges accrued dueto refusal of delivery at the sight
<br />ill be the responsibility of the contractor. Since I.C.C.
<br />regulations require filing of cloirns within o 15—doy period
<br />�"Ull W. L3FNTAMA �01_-T Pg_"iVf X .LrNTEr6;rAi -,
<br />after delivery, it will be the contractor's responsibility to
<br />TcJ' , Cp\L.i FOr�N iA
<br />notify er within this period of any damages or shortages
<br />noted in shipments received. Failure to notify Owner will
<br />------- --- -�
<br />require the contractor to satisfy any or ail claims.
<br />WK DAic REYIS rr
<br />Xi -2 TAN
<br />Underground tanks and piping will be installed and tested
<br />"Submerged
<br />SHELL OIL COMPANY
<br />strictly in accordance with details and notes on the
<br />HOUSTON, TEXAS
<br />Pump and Underground Storage Tank" drawing, a part of the
<br />contract drawings. All local ordinances regarding tank instal
<br />lotions must be observed and it will be the contractor's
<br />GEl"N'ER P E IF ICA T
<br />responsibility to obtain inspections and final approvals.
<br />1"N'
<br />Refer to Sections XIV & XV for further details and Tank
<br />R FACILITIES
<br />InstallationDrawings,
<br />IE T 4 3
<br />-
<br />sr.c� onrvo
<br />°Arc NTM o
<br />
|