Laserfiche WebLink
Document management portal powered by Laserfiche WebLink 9 © 1998-2015 Laserfiche. All rights reserved.
N <br />A <br />u <br />General Conditions of the Contract as contained in either A.I.A. Form <br />A-107 or Shell Oil Company approved Purchase Order Form , whichever <br />utilized, Addenda to Specifications, Asphalt Paving Specifications, <br />and Equipment Schedule ore hereby mode a port of these Specifications <br />to the some extent as if bound herein. The General Conditions, <br />including Modifications and Special Conditions herein, shall opply, to <br />both Prime and Sub -Contractors and all tradesmen. <br />I -I <br />DRAWING <br />Owner will furnish free of charge 6 sets of working drawings <br />and specifications. <br />1-2 PLANS & SPECIFICATIONS <br />General Contractor will check all plans and specifications for <br />compliance with local and state building codes and for errors <br />and omissions. General Contractor will be responsible for <br />notifying Owner's Representative of any discrepancies and when <br />required, adjust bid price accordingly. <br />I-3 IAYING OUT W -BE <br />General Contractor will immediately upon entering project site <br />for purpose of beginning work, locate all general reference <br />points, properly corners, etc., and lake such action as is <br />necessary to prevent their destruction lay out his own work <br />and be responsible for all lines, elevations and measurements <br />of buildings, groding, paving, utilities and other work <br />executed by him under the Contract. No footings or foundations <br />shall be poured prior to field check by Owner's Representative. <br />Any property carriers destroyed, removed or relocated shall be <br />replaced by Registered Land Surveyor at Contractor's expense. <br />General Contractor to meet oil Shell, Slate and Federal Safety <br />requirements. (Refer to section on Safety <br />Guidelines/Requirements.) <br />1-7-4-b. Contractor shall periodically check all machinery and <br />equipment and insure. it is in good operating condition. <br />All Contractor's; Fabricator's equipment is subject to <br />inspection by Company representative, equipment which the <br />Company representative considers hazardous to personnel or <br />facilities must be shut down and/or removed from the <br />premises immediately. Equipment shall be kept at least <br />(25) foot radius away from any operational gasoline <br />dispensing area. <br />1-7-4-c. Contractor's and Fabricator's personnel are directly <br />responsible for "good housekeeping" awareness and assign <br />someone daily for removing clutter from the work areas. <br />Site shall be left in a clean, neat, orderly, and safe <br />condition upon completion of each work day. <br />1-7-4-d. Instruct employees in safe lifting practices which may <br />prevent many injuries. <br />1-7-4-e. Impress upon the workers the need for constant awareness <br />Pven during automatically controlled operations of <br />equipment, etc. <br />1-7-4-f. Contractor, Fabricator or both shall provide his men with <br />proper safety equipment such as goggles, ear plugs, <br />protective clothing, etc., and insure that equipment is <br />used properly. <br />1-7-4-g, Hard Hots will be worn while any overhead work is taking <br />place. (no exceptions) <br />1-7-4-h. Barricades, flags, steel plotes over trenches, including <br />proper sloping and shoring of trench walls, provided by <br />Contractor or Fabricator as necessary to safely secure site <br />and protect all vehicle and' pedestrian traffic on and <br />near fob site. <br />I -7-4-i. Contractor, Fabricator shall protect adjoining properly, <br />earthwork, trees, etc„ from damage and give proper written <br />notice of proposed work to adjoining properly owners. <br />Damage to adjoining properties by Contractor's or <br />Fabricator's activities sholl be repaired at the <br />Contractor's or Fabricator's expense. <br />1-7-4-j. Contractor, Fabricator shall provide all necessary first- <br />aid, ambulance, and hospital services, in case of injury to <br />Contractor's, or Fabricator's employees on Shell premises, <br />1-7-4-k. Shell representative will notify dealer or station manager <br />(24) hours prior to Contractor, Fabricator commencing any <br />minor maintenance work. Dealer or station Manager will be <br />notified a minimum of (3) days prior to Contractor, <br />Fabricator commencing any major maintenance work. <br />1-7-4-I. Contractor, Fabricator shall NOT use Shell,s or Dealers <br />tools. <br />1-7-4-m. Contractor, Fabricator shall have a 20# ABC fire <br />extinguisher readly available for any work at project site <br />which involves use of a sparking device, or open flame, <br />1-7-4-n. No smoking is allowed with twenty-five feet of area where <br />product is being dispensed or released or whenever gasoline <br />vapors are present. Dealer has authority to prohibit <br />smoking on his facility. <br />1-7-5 FIRE CONTROL <br />1-7-5 Incose of fire the following general procedure may be used: <br />Notice: Contractor, Fabricator should consider the <br />specific situation before acting. <br />1-7-5-a. Turn off emergency disconnect switch or main breaker. <br />1-7-5-b. Evacuate area immediately. <br />1-7-5-c. Contact Local Fire Department. . <br />1-7-5-d. Attempt to extinguish only small fires or keep it from <br />spreading to adjacent areas. If fire is out of control <br />leave the area to avoid risk of injury. Notice: Use <br />dry chemical fire extinguisher ABC type to combat small <br />gasoline fires. <br />1-7-5-e. Fueling of running equipment is not allowed. <br />1.6 WELDING <br />1-7-6-a. WARNING - Contractor, Fabricator are responsible at all <br />time to keep personnel alert to potential hazards in the <br />work environment. You are subject to the presence of higly <br />compbustible materials. <br />1-7-6-b, Contractor; Fabricator shall be responsible for furnishing <br />his own equipment and personnel for testing the work area <br />to insure safe conditions prior to and continously during <br />any welding work. <br />1-7-6-c. Contractor; Fabricator shall provide locks to secure all <br />dispensers when equipment is present on construction site. <br />1-7-6=d. Contractor; Fabricator shall provide a Standby Fire Watch <br />person with a 20# ABC fire extinguisher near work area <br />vicinity during entire welding job, <br />1-7-6-e. All welding work should be done in Contractor's; <br />Fabricator's shop or away from gasoline dispensing area if <br />at all possible. <br />1-7-7 ELECTRICAL <br />1-7-7-a. Contractor; Fabricator shall turn off and lock out or <br />disconnect all electrical power isloaling specific circuit <br />or circuits at panel before starting any electrical work. <br />Circuit switch or breaker to be tagged to inform other <br />pro ect workman or station personnel of work in progress <br />an � ovoid accidental startup of power. <br />1-7-7-b. After disabling system and before starting work, <br />Contractor, or Fabricator shall try to activate equipment <br />on that circuit to insure correct system has been locked <br />out. <br />1-7-7-c. Electric panel shall be re-lobelled to reflect any wiring <br />changes by Contractor. <br />1-7-7-d. All electric work shall be in accordance with the latest <br />National Electric Code. <br />1-7-7-e. Special Note: Use only "GFI" or (3) prong plug and socket <br />electrical trouble cords. Cords must be inspected <br />routinely while on job site to ensure safe working <br />conditions. <br />1-7-8 _ GENERAL EQUIPMENT <br />1-7-8-a. All fire extinguishers used by Contractor shall have an <br />occurate-annual inspection be lagged and show when inspections <br />were performed deficiencies found and time corrected. <br />30(1 W. 13E-NJAMIN H61_1 )RING &. TNT[K5T/\TE 5 <br />(91 . SHELL OIL COMPANY <br />HOUSTON, TEXAS <br />GENERAL SPECIFICAITGNS <br />RETAIL FACILITIES <br />SHEET # 1 <br />SCALE DKD/APUD <br />DAtt-- -- vveavtI T <br />EV,L rr A. alflcoN - DR - 9005 <br />LKCK0 it r-TQYf1f�-- .J <br />I N D E X <br />I. <br />General Conditions & Safety Requirements <br />I-4 <br />TEMPORARY UTILITIES <br />II. <br />Clearing Site <br />General Contractor will make arrangements for and furnish, at <br />his own expense, all water, electricity and other utilities <br />III, <br />Excavation, Backfilling and Grading <br />necessary for construction purposes including telephone and „ <br />temporary toilet. General Contractor directly responsible for <br />IV. <br />Concrete Work <br />obtaining all ELECTRICAL & UTILITY PERMITS INCLUDING FINAL <br />CONNECTIONS. <br />V. <br />Masonry Work <br />1-5 <br />PERMITS <br />VI. <br />Structural Steel & Sheet Metal Work <br />Shell Oil Company will furnish building. permit. General <br />Contractor will secure and pay for all other permits, fees, <br />VII. <br />Carpentry and Millwork <br />licenses, etc., that may be necessary to complete the project <br />unless otherwise specified in addenda. Modular building <br />VIII, <br />Roof Decking <br />fabricator to furnish all necessary fabrication, foundation and <br />IX. <br />Plumbing & Piping <br />detail drawings required by local municipalities as well as <br />provide the required State Product Approval permit for each <br />modular building including State certification and <br />X. <br />Heating, Ventilating and Air Conditioning <br />documentation. <br />Mart and C -Store Refrigeration <br />Mort and C -Store Cooler <br />1-6 <br />REMOVAL. ET <br />ETC, OF UTILITIES <br />Mort and C -Store Fast Food Equipment <br />XI. <br />Equipment Installation <br />General Contractor will arrange for and pay all costs, if any, <br />ncidentol to the removal or relocation, as shown on the General <br />Layout, Grade Plan and/or Survey of utility poles, fire hydrants <br />XII. <br />Electricol <br />,street drains or other municipal and/or utility company service <br />installations, unless otherwise specified in addenda. <br />XIII. <br />Connection to Utilities <br />1-7 <br />JOB I1 ALTH AND SAFETY GUIDELINES <br />XIV. <br />Fiberglass Underground Storage Tanks Installation Specifications <br />Peogrovel Backfill <br />i-7-1 PURPOSE The purpose of these instructions is to acquaint <br />XV. <br />Gasoline Piping Specifications <br />you with some of the general rules & regulations pertaining to <br />your work at Shell's Retail Facility. Your compliance with <br />these regulations is mandatory. Only a Min, requirement and <br />XVI, <br />Finish Grading and Landscaping <br />shall not be construed as complete' or comprehensive. It is the <br />direct resposibilily of the contractor; Fabricator or both to <br />XVII. <br />Paving <br />9 <br />insure that their employees have a safe work place and are <br />performing their work safely. including shell's existing <br />XVIII. <br />Clean Up and Final Payment <br />facility personnel, and costomers. If station is operating, <br />Dealer, and Contractor, must exchange "HAZCON" <br />XIX. <br />Pointing <br />information, perOSHA 1910.1200, .. <br />1-7-2 CONTRACTOR/FABRICATOR The term "Contractor or Fabricator" <br />as used in these instructions, shall be understood to include, <br />the Contractor, Fabricator, their workers and any subcontractors <br />and their workers performing work under the terms of the <br />contract under consideration. Contractor, Fabricator is <br />SCOPE <br />responsible for' its workers and subcontractors and for directing <br />and supervising their work. <br />A. The General will include the furnishing of all labor, <br />"Company <br />-contract <br />materials, equipment and services necessary for the construction of <br />1-7-3 COMPANY The term Representative" used in these <br />a complete operating service station facility, including equipment <br />guidelines shall be any engineer, construction & maintenance <br />as shown on the construction drowinys and listed on General Layout <br />representative, or maintenance person designated by Shell Oil <br />and, hereinafter specified: <br />Company. <br />B. The Fabricator will include the furnishing of all labor, <br />1-7-4 GENERAL <br />materials, equipment and services necessary for the construction of <br />customer covers, and modular buildings as shown on the construction <br />1-7-4—a. Safety grgulations of Shell Oil Company must be followed at <br />drawings and listed on General Layout and hereinafter specified: <br />all limes. Company representatives will hove complete <br />authority to stop work if any violation of the safety <br />guidelines are recognized. <br />General Conditions of the Contract as contained in either A.I.A. Form <br />A-107 or Shell Oil Company approved Purchase Order Form , whichever <br />utilized, Addenda to Specifications, Asphalt Paving Specifications, <br />and Equipment Schedule ore hereby mode a port of these Specifications <br />to the some extent as if bound herein. The General Conditions, <br />including Modifications and Special Conditions herein, shall opply, to <br />both Prime and Sub -Contractors and all tradesmen. <br />I -I <br />DRAWING <br />Owner will furnish free of charge 6 sets of working drawings <br />and specifications. <br />1-2 PLANS & SPECIFICATIONS <br />General Contractor will check all plans and specifications for <br />compliance with local and state building codes and for errors <br />and omissions. General Contractor will be responsible for <br />notifying Owner's Representative of any discrepancies and when <br />required, adjust bid price accordingly. <br />I-3 IAYING OUT W -BE <br />General Contractor will immediately upon entering project site <br />for purpose of beginning work, locate all general reference <br />points, properly corners, etc., and lake such action as is <br />necessary to prevent their destruction lay out his own work <br />and be responsible for all lines, elevations and measurements <br />of buildings, groding, paving, utilities and other work <br />executed by him under the Contract. No footings or foundations <br />shall be poured prior to field check by Owner's Representative. <br />Any property carriers destroyed, removed or relocated shall be <br />replaced by Registered Land Surveyor at Contractor's expense. <br />General Contractor to meet oil Shell, Slate and Federal Safety <br />requirements. (Refer to section on Safety <br />Guidelines/Requirements.) <br />1-7-4-b. Contractor shall periodically check all machinery and <br />equipment and insure. it is in good operating condition. <br />All Contractor's; Fabricator's equipment is subject to <br />inspection by Company representative, equipment which the <br />Company representative considers hazardous to personnel or <br />facilities must be shut down and/or removed from the <br />premises immediately. Equipment shall be kept at least <br />(25) foot radius away from any operational gasoline <br />dispensing area. <br />1-7-4-c. Contractor's and Fabricator's personnel are directly <br />responsible for "good housekeeping" awareness and assign <br />someone daily for removing clutter from the work areas. <br />Site shall be left in a clean, neat, orderly, and safe <br />condition upon completion of each work day. <br />1-7-4-d. Instruct employees in safe lifting practices which may <br />prevent many injuries. <br />1-7-4-e. Impress upon the workers the need for constant awareness <br />Pven during automatically controlled operations of <br />equipment, etc. <br />1-7-4-f. Contractor, Fabricator or both shall provide his men with <br />proper safety equipment such as goggles, ear plugs, <br />protective clothing, etc., and insure that equipment is <br />used properly. <br />1-7-4-g, Hard Hots will be worn while any overhead work is taking <br />place. (no exceptions) <br />1-7-4-h. Barricades, flags, steel plotes over trenches, including <br />proper sloping and shoring of trench walls, provided by <br />Contractor or Fabricator as necessary to safely secure site <br />and protect all vehicle and' pedestrian traffic on and <br />near fob site. <br />I -7-4-i. Contractor, Fabricator shall protect adjoining properly, <br />earthwork, trees, etc„ from damage and give proper written <br />notice of proposed work to adjoining properly owners. <br />Damage to adjoining properties by Contractor's or <br />Fabricator's activities sholl be repaired at the <br />Contractor's or Fabricator's expense. <br />1-7-4-j. Contractor, Fabricator shall provide all necessary first- <br />aid, ambulance, and hospital services, in case of injury to <br />Contractor's, or Fabricator's employees on Shell premises, <br />1-7-4-k. Shell representative will notify dealer or station manager <br />(24) hours prior to Contractor, Fabricator commencing any <br />minor maintenance work. Dealer or station Manager will be <br />notified a minimum of (3) days prior to Contractor, <br />Fabricator commencing any major maintenance work. <br />1-7-4-I. Contractor, Fabricator shall NOT use Shell,s or Dealers <br />tools. <br />1-7-4-m. Contractor, Fabricator shall have a 20# ABC fire <br />extinguisher readly available for any work at project site <br />which involves use of a sparking device, or open flame, <br />1-7-4-n. No smoking is allowed with twenty-five feet of area where <br />product is being dispensed or released or whenever gasoline <br />vapors are present. Dealer has authority to prohibit <br />smoking on his facility. <br />1-7-5 FIRE CONTROL <br />1-7-5 Incose of fire the following general procedure may be used: <br />Notice: Contractor, Fabricator should consider the <br />specific situation before acting. <br />1-7-5-a. Turn off emergency disconnect switch or main breaker. <br />1-7-5-b. Evacuate area immediately. <br />1-7-5-c. Contact Local Fire Department. . <br />1-7-5-d. Attempt to extinguish only small fires or keep it from <br />spreading to adjacent areas. If fire is out of control <br />leave the area to avoid risk of injury. Notice: Use <br />dry chemical fire extinguisher ABC type to combat small <br />gasoline fires. <br />1-7-5-e. Fueling of running equipment is not allowed. <br />1.6 WELDING <br />1-7-6-a. WARNING - Contractor, Fabricator are responsible at all <br />time to keep personnel alert to potential hazards in the <br />work environment. You are subject to the presence of higly <br />compbustible materials. <br />1-7-6-b, Contractor; Fabricator shall be responsible for furnishing <br />his own equipment and personnel for testing the work area <br />to insure safe conditions prior to and continously during <br />any welding work. <br />1-7-6-c. Contractor; Fabricator shall provide locks to secure all <br />dispensers when equipment is present on construction site. <br />1-7-6=d. Contractor; Fabricator shall provide a Standby Fire Watch <br />person with a 20# ABC fire extinguisher near work area <br />vicinity during entire welding job, <br />1-7-6-e. All welding work should be done in Contractor's; <br />Fabricator's shop or away from gasoline dispensing area if <br />at all possible. <br />1-7-7 ELECTRICAL <br />1-7-7-a. Contractor; Fabricator shall turn off and lock out or <br />disconnect all electrical power isloaling specific circuit <br />or circuits at panel before starting any electrical work. <br />Circuit switch or breaker to be tagged to inform other <br />pro ect workman or station personnel of work in progress <br />an � ovoid accidental startup of power. <br />1-7-7-b. After disabling system and before starting work, <br />Contractor, or Fabricator shall try to activate equipment <br />on that circuit to insure correct system has been locked <br />out. <br />1-7-7-c. Electric panel shall be re-lobelled to reflect any wiring <br />changes by Contractor. <br />1-7-7-d. All electric work shall be in accordance with the latest <br />National Electric Code. <br />1-7-7-e. Special Note: Use only "GFI" or (3) prong plug and socket <br />electrical trouble cords. Cords must be inspected <br />routinely while on job site to ensure safe working <br />conditions. <br />1-7-8 _ GENERAL EQUIPMENT <br />1-7-8-a. All fire extinguishers used by Contractor shall have an <br />occurate-annual inspection be lagged and show when inspections <br />were performed deficiencies found and time corrected. <br />30(1 W. 13E-NJAMIN H61_1 )RING &. TNT[K5T/\TE 5 <br />(91 . SHELL OIL COMPANY <br />HOUSTON, TEXAS <br />GENERAL SPECIFICAITGNS <br />RETAIL FACILITIES <br />SHEET # 1 <br />SCALE DKD/APUD <br />DAtt-- -- vveavtI T <br />EV,L rr A. alflcoN - DR - 9005 <br />LKCK0 it r-TQYf1f�-- .J <br />