|
REVISIONS
<br /> E.Outlet boxes shall be Installed plumb and square with wall face and with front of box or cover located within 118 Inch of face of finish 1.03 Regulatory Requirements A.Panel boards shall be Square D'NQOD/NP,ITE Siemens"S3"or Cutler-Hammer"Pow-R-Line PRL1A,PRL2A and PRL3A". All panel 1.03 Codes and Standards nl !J til t"I
<br /> wall. Boxes in masonry shall be set with bottom of the box tight to the masonry unit. boards shall be of the same manufacturer. (9 0 CO (9A.Methods of installation shall comply with the provisions of applicable sections of NEC Adds 300. A.The specified unit shall be designed,manufactured,tested,and installed in compliance with all of the following standards:
<br /> 3.03 Pull and Junction Box and Gutter Installation PART 2 PRODUCTS W
<br /> PART2 PRODUCTS 1.National Electric Code o p
<br /> A.Pull boxes,junction boxes and auxiliary wiring gutters shall be installed where indicated on Drawings and where required to facilitate 2.01 Panel boards 2.American National Standards Institute and the Institute of Electrical and Electronic Engineers(ANSI/IEEE C62.41-1991 andF ut m M
<br /> installation of the wiring. 2.01 General 062.45-1987)
<br /> A.Bussing Assembly and Temperature Rise: Panel board bus structure and main lugs or main breaker shall have current ratings as 3.Canadian Standards Association(CSA) r m
<br /> B.For concealed conduit,boxes shall be installed flush with ceiling or wail,with covers accessible and easily removable. Where flush A.Products shall be used as described under Part 3. shown on the panel board schedule. Such ratings shall be established by heat rise tests with maximum hot spot temperature on any 4.Federal Information Processing Standards Pub.94(PIPS PUB 94) Z
<br /> boxes are installed in finished ceilings or walls,cover shall be provided which shall exceed the box face dimensions by a sufficient amount connector to bus bar not to exceed 50 degrees C rise above ambient. Heat rise test shall be conducted in accordance with Underwriters' 5.National Electrical Manufacturers Association(NEMA) y O Of
<br /> to allow no gap between box and finished material. PART 3 EXECUTION Laboratories Standard UL 67. The use of conductor dimensions will not be accepted in lieu of actual heat tests. Bus bar connections to 6.National Fire Protection Association(NFPA 70[NEC],75,and 78) U
<br /> the branch circuit breakers shall be the"distributed phase"or'phase sequence'type. 7.Underwriters Laboratories(UL 1449 and 1283) Qd Z
<br /> C.Boxes shall not be located in finished,ocoupied rooms,without prior approval of Owner. 3.01 Installation
<br /> Single phase,three-wire panel board bussing shall be configured such that any two adjacent single-pole breakers are connected to 1.04 Qualifications O IY Q
<br /> 3.04 Hanger and Support Installation A.Suitable installation equipment shall be provided to prevent cutting and abrasion by conduits during the pulling of feeders. Ropes used opposite polarities in such a manner that two-pole breakers can be installed in any location. Three-phase,four-wire bussing shall be W m U fn
<br /> for pulling of feeders shall be made of polyethylene or other suitable non-metallic material. Metallic ropes shall not be used. configured such that any three adjacent single-pole breakers are individually connected to each of the three different phases in such a A.Equipment shall be as manufactured by Cuter-Hammer,Square D and Siemens. Q W W W >
<br /> A.Hangers and supports shall be installed for all conduit and boxes. manner that two or three-pole breakers can be installed at any location. Current-carrying parts of the bus assembly shall be plated.Mains
<br /> B.A#14 galvanized steel fish wire or a plastic line having a tensile strength of not less than 200 pounds shall be installed in each conduit, ratings shall be as described in the panel board schedule. Equipment ground bus shall be provided in each panel. 1.05 Warranty J Z = Z J
<br /> B.Conduit and boxes shall not be attached to or supported from mechanical pipes,plumbing pipes,or sheet metal ducts. except underground conduits,in which installation of conductors is not included in this Section of the Specification. A#10 AWG bare,hard d Q - J Wdrawn copper shall be installed in each underground conduit or dud,in which installation of conductors is not included in this Section of the B.Safety Barriers: The panel board interior assembly shall be dead front with panel board front removed. A.The manufacturer shall provide a limited five-year warranty from date of shipment against failure when installed In compliance with ILF y F
<br /> C.Conduits routed in lay-in grid ceiling plenum shall not be supported from the ceiling hanger iron or ceiling tees. Specification. applicable national/local electrical codes and the manufacturer's Installation,Operation and Maintenance Instructions. In N f (n
<br /> CSECTION 16120 - WIRE & CABLE C.Cabins s and Fronts: Panel board assembly shall be enclosed in a steel cabinet The rigidity and gauge of steel shall be as specified J W W
<br /> .Fish wires and lines shall be free from splices and shall have ample exposed length at each end. in UL Standard 50 for cabinets. Wiring gutters shall be in accordance with UL Standard 67 for panel. Minimum gutter 6 inches each side,5 1.06 Submittals Z
<br /> PART 1 GENERAL Inch top and bottom. Fronts shall Include doors and have flush,brushed stainless steel,cylinder tumbler-type locks with catches and m V V F d W U R
<br /> D.Wire pulling lubricants,if used,shall conform to UL requirements applicable to the several insulation and raceway materials. spring-loaded door pulls. The flush lock shall not protrude beyond the from of the door. All panel board locks shall be keyed alike. Front A.Provide verification that the TVSS device complies wit the required UL 1449(IEEE C62.41 Cat.CI-SkV,31A)Surge Voltage Ratings Q 1..1 n. Z O o rc
<br /> 1.01 Scope of Work shall have adjustable indicating trim clamps which shall be completely concealed when the doors are closed. Doors shall be mounted by (SVR). V W () W (� w to
<br /> E.Cables shall not be bent,either permanently or temporarily during Installation,to radii less than 10 times the outer diameters,except completely concealed steel hinges. Fronts shall not be removable with door in the locked position. A circuit directory frame and card with a B.Provide actual Let-Through voltage test data In the form of oscillograph results for ANSI/IEEE C62.41 Cat.C3(2l 1 Cat.Cl Z N 0 U' m
<br /> A.Under this Section of the Specifications the Contractor shall furnish all labor,materials,tools,and equipment required for the installation where shorter radii are approved for conditions making the specified radius impractical. clear plastic covering shall be provided on the inside of the door. The directory card shall provide a space at least 1/4 inch high by 3 inches (6kV,3kA),and Cat.B3(6kv,SODA @100kHz)tested in accordance with ANSI/EEE C62.45. Ur = Z Z Z 0 O O 1-
<br /> of wire and cable in accordance with the Drawings and Specifications. long or equivalent for each circuit. The directory shall be typed to identify the load fed by each circuit. Fronts shall be of code gauge,full Z V W Il.l " " w
<br /> F.Pulling lines shall be attached to conductor cables by means of either woven basket gaps or pulling eyes attached directly to the finished steel with rust-inhibiting primer and gray baked enamel finish. C.Provide spectrum analysis of each unit based on MIL-STD-220A fest procedures between 50 Hz and 200 kHz verifying the device J ? Z V _ _ w D F m
<br /> B.This Section describes the basic materials and methods of installation for general wiring systems of 600 volts and less. Wiring for a conductors. Rope hitches shall not be used. All cables shall be installed in a single conduit shall be pulled in together. Where noise attenuation exceeds 45 d6 at 100 kHz. J Q y O O w w
<br /> higher voltage rating,if required,shall be as specified in other sections or as called for on the Drawings. polyethylene insulation is used and a pulling lubricant is required,the lubricant shall be certified by the manufacturer to be non-injurious to D.Wiring Terminals: Terminals for feeder conductors to the panel board mains and neutral shall be UL listed as suitable for the type of - J
<br /> polyethylene insulation. conductor specified. Terminals for branch circuit wiring,both breaker and neutral,shall be UL listed as suitable for the type of conductor D.For Integrated or Retrofit applications,elecMcaVmechanical drawings showing unit dimensions,weights,installation instruction details, IL m 0 (1) a J U a a Q a v
<br /> C.Minimum size conductors shall be No. 12 AWG for power and lighting and No.14 AWG for signal and control. SECTION 16140 - WIRING DEVICES & PLATES specified. and wiring configuration shall be supplied. ' ' ' ' ' '
<br /> N CD 1 N O r 0 CO)
<br /> 1.02 General Requirements PART i GENERAL E.Circuit Breakers: Circuit breakers shall be quick-make,quick-break,thermal-magnetic,bop indicating,and have common trip on all E.Provide test report(s)from a nationally recognized independent testing laboratory verifying that the suppresser(s)can survive the N �1' (O h h N O O
<br /> multiple breakers. Circuit breakers shall be bolt-on e equipped with individual) insulated,braced and protected connectors. The frons published sure current ratio on a per mode and r phase basis. The test wave shall be the ANSI/IEEE 06241,8x20 microsecond r' r r r r cc to to
<br /> P err. Y P P 9 9 P Pe P (,fl (D fp LO to fp CO O
<br /> A.Related and general provisions of Contract,including General and Supplementary Conditions and Division 1 Specification Sections, 1.01 Scope of Work faces of cirwit breakers shall be Bush with each other. Large permanent individual circuit numbers shall be affixed to each breaker in a current wave. r r r r r r r r
<br /> shall apply to this Section. uniform position. Tripped indication shall be clearly shown by the breaker handle taking a position between ON and OFF.Provisions for
<br /> A.Under this Section of the Specifications the Contractor shall furnish all labor,materials,tools,and equipment required for the installation additional breakers shall be such that no additional connectors will be required to add breakers. Circuit breakers shall have an Interrupting 1.07 Electrical Requirements
<br /> 1.03 Regulatory Requirements of wiring devices in accordance with the Drawings and Specifications. rating as Indicated In the panel board schedule. Circuit breakers used for feeding HVAC equipment shall be HACR rated.
<br /> A.Maximum Continuous Operating Voltage(MCOV). The MCOV shall be greater than 115%of the nominal system operating voltage.
<br /> A.Methods of installation shall comply with the provisions of applicable sections of NEC,Article 300. 1.02 General Requirements F.Integrated Equipment Rating: Each panel board,as complete unit,shall have a rating equal to or greater than the integrated equipment
<br /> rating shown on the panel board schedule. B.The device must have directly connected suppression elements between line-neutral(L-N),line-ground(L-G),and neutral-ground(N-G)
<br /> B.Materials shall be in awordance with NEC,Article 310 and shall be UL listed for application intended. A.Related and general provisions of Contract,including General and Supplementary Conditions and Division 1 Specification Sections, in order to provide full protection.
<br /> shall apply to this Section. G.Each panel board shall have a copper ground bus with lugs to accept all grounding and bonding conductors.
<br /> C.All wire and cable installed inside conduits that exit,enter or go through hazardous area must conform to NEC Article 501-13 for C.UL 1449 SVR. The maximum UL 1449(IEEE 06241 Cat C1 6kV,3kA)SVR for the device must not exceed the following: 0
<br /> conductor insulation. 1.03 Submittals PART 3 EXECUTION Z
<br /> Modes 21 4BOY1277 600Y/347 J
<br /> 1.04 Quality Assurance A.Prior to the purchase dwiring devices and plates,Shop Drawings shall be submitted for approval in accordance with the requirements 3.01 Installation _J
<br /> of Section 01300. WYE-L-N;L-G;N-G 400V BOOV 1200V l.L
<br /> A.The material used for the wiring systems shall be the products of a manufacturer regularly engaged in the manufacturing of the A.Panel boards shall be securely anchored to structure and feeder and branch circuit connections made as indicated on the Drawings. Delta-L-L,L-G 800V 1500V 2000V Y
<br /> specified material. Where a manufacturer is named for a particular material,the material of other manufacturers will be acceptable 1.04 Regulatory Requirements U
<br /> provided the material meets requirements of the Specifications. B.An engraved nameplate shall be Installed on front trim of each panel as described in Section 16051 of this Specification. D.ANSI/IEEE Cat.C3 Let Through Voltage. Let Through Voltage based on ANSI/IEEE Cl and C62.45 recommended procedures for Q
<br /> A.Except where oMerwise required by this Section,the following Standards and Codes shall govern: Cat.C3 surges(20 kV, 1OkA)shall be less than: cn In
<br /> PART2 PRODUCTS C.The grounded side of each branch circuit shall be fed directly from the neutral bus. The circuit breaker shall contain the ungrounded 0
<br /> 1. Receptacles;NEC Article 410-L. side of each branch cirou@. Modes 21 480Y/277 600Y/347 O 06
<br /> 2.01 Wire and Cable 2. Wall Switches;NEC Article 380. _ (D
<br /> 3. UL Listed. D.All panel boards shall be tested for cored grounding and check mechanicel operation of all breakers and switches. L-N 500V 900V 1300V Z
<br /> A.Wire and cable for power,lighting,control and signal circuits shall have copper conductors of not less than 98 percent conductivity and 4. NEMA Standards W
<br /> shall be insulated In 60OV. Conductors shall be stranded except where specifically noted otherwise. SECTION 16170 - DISCONNECT SWITCHES E.ANSI/IEEE Cat B3 Let Through Voltage. Let Through Voltage based on ANSI/IEEE C62.41 and C62.45 recommended procedures for (� _
<br /> 1.05 Quality Assurance PART 1 GENERAL the ANSI/IEEE Cat.B3 Ringweve(e kV,500 amps)shall be less than: Z O
<br /> B.Type of wire and cable for the various applications shall be as follows: 0 = W fn
<br /> A.Products by Harvey Hubbell,HBL Series, Bryant-Industrial Spec,Pass&Seymour-Industrial Spec Grade,or Levilon-Industrial 1.01 Scope of Work Modes 208Y/120 480YI277 601 fn O2
<br /> its,
<br /> 1.Type THWN or XHHW(75 degrees C)shall be used for branch circupanel and equipment feeders in wet and dry locations. Spec Grade shall be acceptable. Q Z F O � IIJ
<br /> A.Under this Section of the Specifications the Contractor shall furnish all labor,materials,tools,and equipment required for the installation L-N 170V 300V 470V H W
<br /> 2.Type THHN or XHHW(90 degrees C)shall be used for branch circuits,panel and equipment feeders in dry locations only and used PART2 PRODUCTS of fused and non-fused disconnect switches in accordance with the Drawings and Specifications. d _Z fn J z
<br /> where lighting branch circuit conductors are routed through fluorescent Whom channels. F.All units must be tested to the specified surge ratings to ensure the devices)will achieve the required life expectancy and reliability. W EL Z r m z
<br /> 2.01 General 1.02 General Requirements Testing to full ratings also verifies internal construction quality of the suppressor(s). Test data must be provided from an intlepentlent test F k>t$ LL _ Q
<br /> 3.Type AF or SF-2 silicone rubber with heat-resistant glass braid(rated minimum 150 degrees C)shall be used for branch circuit lab capable of producing 20011A surge current wave forms using the ANSI/IEEE C62.41 impulse wave form(8x20 microsecond). Withstand Q JO ;;-
<br /> conductors connecting tufixture conductors within the fixture housing ortoaconnection box attached tothe flztureand subject to A.All wiring devices shall be'Specification Grade"except where higher grade is rolled for. A.Related and general provisions of Carred,including General and Supplementary Conditions and Division l Specification Sections, testing must be provided on a per mode and per phase basis. Ozo�pm
<br /> temperatures equal to the temperatures within the fixture housing. shall apply to this Section. (� W Z (n � zoo$n
<br /> 2.02 Switches G.Branch circuit panel minimum surge current capacity per phase shall be 120kA. Minimum surge current per mode shall be 6OkA. F W Q W w a:d
<br /> 2.02 Conductor Color Coding and Identification 1.03 Submittals fn Z Q. U Z l m-1 S m
<br /> _ o
<br /> A.Wall switches shall be as described in the Symbol Schedule an the Drawings. H.Service entrance minimum surge current per phase shall be 250kA. Minimum surge current per mode shall be 125kA. Q W X 0 o N w 0...4
<br /> A.Wiring systems shall be color coded. Conductor Insulation shall be colored in sizes up through No.8 AWG. Conductors No.6 AWG A.Submittal data shall be standard catalog Information showing necessary technical data and dimensions in accordance with Section m O U I.L. W L) w O
<br /> and larger shall have black insulation and shall be phase color called with 1/2 inch band of colored tape at all junctions and terminations. 2.03 Receptacles 01300. PART 2-PRODUCTS . I I I r r a $u a
<br /> Colors shall be assigned to each conductor as described below and carried throughout all main and branch circuit distribution. r M V O O r O
<br /> 120/208 Volt 277/480 Voll A.Receptacles shall be as described in the Symbol Schedule on the Drawings. 1.04 Regulatory Requirements 2.01 SPDITVSS Design 1.0 Ln LO O CO r N
<br /> 1. Phase'W contludor Black Brown 0 0 0 O O r r
<br /> 2. Phase'S'conductor Red Orange 2.04 Cover Plates A All switches shall be UL listed and so labeled. They shall also meet NEMA enclosed switch standard KS1-1969 for type HD and JIC A.Balance Suppression Platform. The surge current shall be equally distributed to all MOV components to ensure equal stressing and Cr0 CD ID to CD to (0 Z
<br /> 3. Phase'C'conductor Blue Yellow electrical performance specifications. maximum performance. The surge suppression platform must provide equal impedance paths to each matched MOV.
<br /> 4. Neutral conductor White Gray A.Plates for flush devices shall be non-breakable nylon,similar to Hubbell"P"series. Plates shall match device color.
<br /> 5. Grounding conductor Green Green 1.05 Quality Assurance B.Electrical Noise Filter. Each unit shall include a high performance Evil noise rejection filter. Noise attenuation for electric line noise 0B.Plates shall be provided for all switches,receptacles,other outlets and blank plates for all unused outlets. shall be complimentary listed to UL 1283. Products notable to demonstrate noise attenuation of 45dB @ 100 kHz.Asa minimum shall be
<br /> B.Contractor shall take extraordinary care to ensure that phase and bus orientation in each and every panel is identical. A.Disconnect switches shall be Square D,ITE or Cutler-Hammer type"Dill rejected. Z
<br /> C.Plates for outlets for dock areas and other surface mounted locations shall be galvanized pressed steel. (inc ® -
<br /> C.Control wiring shall be color coded such that red is used exclusively for all 120 volt conductors and white for all neutral conductors. All PART2 PRODUCTS C.Internal Connections. All internal components shall be hardwired with connections utilizing low impedance conductors and Ir
<br /> control wiring shall be identified at both ends with permanent wire markers. D.Where two or more devices are set at one point,they shall be covered with a common plate. compression fittings. 0 W
<br /> 2.01 GeGeneral2.03 Connectors E.Where devices are mounted outdoors,deep cover UL listed for wet location while in use"shall be provided as manufactured by D.Safety and Diagnostic Monitoring. Each unit shall be equipped with standard ovemurrent protection: WTaymac Industries. A.Disconnect switches shall be heavy duty type enclosed switches of quick-make,quick-break construction. 2 Z
<br /> A.In-line splices and taps for copper conductor sizes No.a AWG and smaller;3M Company"Live Sprang"insulated rigid nylon wiring style 1.Continuous monitoring o lug system.
<br /> body or 3M"Ranger'or equal. PART 3 EXECUTION B.All switches shall be horsepower and 12t rated. 2.Monitor individual Ml(including neutral to ground). The system must be capable of identifying open circuit failures not monitored U) 'R
<br /> by conventional fusing systems. V
<br /> 3.01 Installation C.The operating handle shall be of the box-mounted a that directi drives the switch mechanism suitable for padlocking In the"OFF"
<br /> B.In-line connectors for copper conductors BOOV or less,sizes#6 AWG through 3 AWG;ILSCO type"CT"circumferential compression p 9 type Y P g 3.Monitor for overheating in all modes due to thermal runaway. F W Z
<br /> sleeves shall be used. Conductors#2 AWG and larger;extra long barrel ILSCO type"CTL"with 3M Brand"PST"silicone cold shrink position with up to 3 padlocks of 5/16 inch diameter shanks. Detestable,front accessible,"coin proofintedocks shall be provided to Z W l O W
<br /> insulators shall be used. Equivalent sleeves by T&B or Buchanan shall be acceptable. A.Wiring devices shall be installed as indicated on the Drawings,and as called for below. prevent the opening of the cover when the switch is in the"ON"position and prevent turning the switch"ON"when the door is open. Agreen/red solid state indicator light shall be provide on each phase. The absence of a green light and the presence of a red light shall W U)
<br /> f Securely fastened metallic nameplate shall include highly visible"ON-OFF'indication. indicate which phase(s)have been damaged. Fault detection will activate a flashing trouble light. Units that can not detect open circuit l }
<br /> C.Taps for copper conductor 600V or less,saes No.6 AWG and larger;use ILSCO"AH"series shall be used. Equivalent sleeves by T& B.Switches and receptacles shall be installed and located as follows,unless noted otherwise on Drawings: damage,thermal conditions,and over current will not be accepted. Y W � W
<br /> B or Buchanan will be acceptable. D.All units shall be supplied with Class R rejection fuse dips. fn
<br /> ,
<br /> 1.Switches: 48 inches above finished ficom or as noted on Drawings. E.The panel board shall be constructed using a direct bus bar connection(no cable connection between bus bar and SPD/NSS). Panel O W U X O
<br /> D.Copper cable terminations to bus bars,switch studs and terminal blocks:O-Z Manufacturing Company"Shurelug"solder less tugs,or E.The interior shall be easily removable. At least one side wiring gutter shall beclear of any obstructions and moving parts. boards that use a wire connection do not meet the intent of this specification. O Z W Z
<br /> rs
<br /> equivalent shall be used. 2.Receptacles: 18 inches above finished Flooor as noted on the Drawings;36 inches above unfinished floors or 8 inches above O (n J
<br /> counters and work benches in shops,mechanical equipment rooms and similar areas. F.Enclosures shall be NEMA Type l in dry locations and NEMA Type 4(stainless steel)in damp and wet locations and in locations F.All monitoring diagnostics features such as indicator lights,trouble alarms and surge counter(if specified)shall be visible from the front 2 Z U 2 W
<br /> E.Splices and taps shall be Insulated to thickness of conductor Insulation with half-lapped layers of 3M"Scotch"brand No.33 vinyl exposed to weather. of the panel. IX W fn
<br /> electrical tape.. Connectors having Irregular surfaces;voids shall be filled and contours smoothed with 3M"Scolchfil"electrical putty prior to C.In masonry walls,switches and receptacle heights shall be adjusted as required so outlets are at nearest mortarjoinl to specified O W 0 5 LL
<br /> taping. 3M Brand series'PST'silicone cold shrink insulating sleeves are also acceptable. height. G.Current and voltage ratings and number of poles shall be as indicated on the Drawings. 2.02 Accessories LL IX
<br /> PART 3 EXECUTION g j y opening, W W J O W 3
<br /> D.Where light switches are located adjacent to doors,the shall be installed on"knob"side of door o enin unless indicated otherwise. H.Each enclosure shall contain a ground lug to accept incoming and outgoing ground conductors. A.The units must be equipped with an integral audible alarm. F F _J In Z W `<£
<br /> B.Remote Status Monitor. The T/SS device must include Form C dry contacts(one N.O.and one N.C.)for remote annunciation of unit W W z Z Z x Q ��
<br /> 3.01 Preparation E.Where walls have wainscot finish,switch height shall be adjusted as required so switch is either all in wainscot or all in wall above I.Disconnect shall be provided with auxiliary interlock kit where required to discerned external power control wiring. status. The remote alarm shall change state if any of the three monitoring systems described detect a fault condition.
<br /> wainscot. 0 C1 F W O J £
<br /> A.Wiring shall not be installed in the conduit system until the building is enclosed and masonry work is completed. PART 3 EXECUTION C.Push-To-Test Feature. Each suppression unit shall incorporate an integral test feature,which verifies the operational integrity of the Z ZZ IIA
<br /> F.Prior to roughing-in outlet boxes,Contractor shall verify from general construction Drawings door swings,type of wall finishes and unit's monitoring system. O O Q W Q J K rr'+ og
<br /> B.Conduit shall be swabbed free of moisture and debris prior to pulling In wire. locations for counters and work benches. 3.01 Installation Q u>
<br /> p p g SECTION 16450 - GROUNDING U U U N LL li Q LL U z'. a�
<br /> G.This section Contractor shall provide material as required to completely install work indicated on the Drawings which is located in mill r r r J Q id< a2
<br /> 3.02 Installation and casework. A.Anchor disconnect switches shall be securely anchored to structure or equipment housing and make wiring connections as indicated on PART 1 GENERAL r W LL O A
<br /> the Drawings. O O O O O Li (O D M U air
<br /> 3 A.Came for major feeders shall be continuous from origin mmi
<br /> termination. SECTION 16165 BRANCH CIRCUIT PANELBOARDS, CIRCUIT BREAKER TYPE 1.01 Scope of Work r N M O O N V L_ e;� 9
<br /> o B.An engraved nameplate shall be installed on front of each switch enclosure to identify load served,in accordance with the identification CO Cl) M f-- O O NO J Q ,r ;;6
<br /> 0 B.Splices in branch circuit wires shall be made only in accessible junction boxes. PART 1 GENERAL requirements of Section 16051. A.Under this Section of the Specifications the Contractor shall furnish all labor,materials,tools,and equipment required for the installation O O O O O r r R -
<br /> SECTION 16171 - SURGE SUPPRESSION of grounding conductors and fittings in accordance with the Drawings and Specifications. ~
<br /> m C.Power feeder cable shall be pulled with the use of approved pulling compound or powder,and per the requirements of Section 16125. 1.01 Scope of Work 0 Eco
<br /> SECTION 16125 - PULLING CABLES PART t -GENERAL 02 General Requirements
<br /> m A.Under this Section of the Specifications the Contractor shall furnish all labor,materials,tools,and equipment required for the installation L,n^bo
<br /> PART 1 GENERAL of branch circuit panel boards in accordance with the Drawings and Spedfcations. 1.01 Related Dowmentsr A.Related and general provisions of Contract,including General and Supplementary Conditions and Division 1 Specification Sections, vJ rico
<br /> shall apply to this Section. Z
<br /> 3 $U
<br /> -o B.Panel boards described in this Section shall be dead-front safe a furnished with bolton thermal-magnetic molded case circuit A.The other Contract Documents complement there uirements of this Section. The General Requirements apply to the work of this
<br /> 1.01 Scope of Work safety it b g p q q pp y
<br /> breakers for lighting,receptacle and branch circuit applications. Circuit breakers shall have frame and trip ratings as scheduled on Section. 1.03 Regulatory Requirements J O_a8
<br /> M' A.Under this Section ofthe Specifications the Contractor shall furnish all labor,materials,tools,and equipment required for the installation Drawings. 1 1 1 ® L€
<br /> U of wire and cable in raceways in accordance with the Drawings and Specifications. 1.02 Summary A.Except where otherwise required,the following codes shall govern: W O
<br /> C.Refer to Section 16171 for NSS requirements. Q X 7 Q£$
<br /> 1.02 General Requirements A.The following specification describes the requirements fora Surge Protection Device(SPD)rrmnsient Voltage Surge Suppresser 1. NEC,Article 250. Z r"1 U o0
<br /> 1.02 General Requirements (NSS)protection system indicated on the drawings and schedules. 2. NFPA 101. ' O ri
<br /> A.Related and general provisions of Contract including General and Supplementary Conditions and Division 1 Specification Sections, 3. UL Listed. L
<br /> t j shall apply to this Section. A.Related and general provisions of Contract,including General and Supplementary Conditions and Division 1 Specification Sections, B.NSS units shall be integral with the 208/120 vo8 branch circuit panels and switchboard 4MD where noted on the plans. Off`
<br /> shall apply to this Section. PART 2 PRODUCTSZ Z (n U a
<br /> W
<br /> O W W LLI9a�
<br /> 1.03 Submittals 2.01 General ��/)
<br /> V
<br /> U) W �a a
<br /> Of
<br /> N '^
<br /> ty A.Shop Drawings shall include fabrication details,lug and bus arrangement,ampere and voltage rating,breaker frame sizes,and A.Service ground conductors and grounding conductors installed below slab on grade shall be bare stranded copper. O 0 z F. vJ¢tto_
<br /> interrupting ratings in accordance with Section 01300. Q O Z Ej
<br /> _ W Q W
<br /> E
<br /> 1.04 Regulatory Requirements 06 W Z U SCALE:
<br /> w Ur Z O W W N.T.S.
<br /> A.Fabrication and installation shall comply with applicable Sections of NEC,Article 384. Equipment shall bear UL labels.
<br /> 0 1.05 Quality Assurance Z Y - W U ¢ DRAWN BY:
<br /> U Ofof ¢ fn � mQ
<br /> M- } W pn cLz
<br /> QO
<br /> J W af O Z J DATE:
<br /> OfZ
<br /> W ofZ Q2' m W PROJECT NO.
<br /> U W W (n (n Q 7 LL CA-1098
<br /> W ' ' ' ' ' ' ' DRAWING NO.
<br /> ^ 0 0 0 0 0 0 0
<br /> Ll CO O I-- M O N V
<br /> N MM (n O ri n C-6
<br /> N N N N N N N J lJ
<br /> 0 0 0 0 0 0 0
<br />
|