INSTALL_PLAN 2003 - Laserfiche WebLink

Home Browse Search

12" DIA. x 2'-0" CONC BURIED BASE (TYP.) 2" U -BOLTS (TYP.) -\ 2" DIA. - 90'_ GALVANIZED ELL 2" GALVANIZED SCH 40 VENT RISER AT 12' ABOVE GRADE (P/V VENT PER LOCAL CODE) 2" DIA, x 8'-0" GALVANIZED SCH 40 SUPPORTS 7'-0" ABOVE GRADE (TYP.) 1/8" x 4" x 18" UNI -STRUTS AT 3' AND 5' ABOVE GRADE 2" FRP GASOLINE VENT SLOPE VENTS DOWN 1/B " PER FT. TO TANKS (TYP. ALL LINES 2" DIA. MALE ADAPTER VENT RISER DETAIL NOT TO SCALE NOTE: ALL DISPENSERS ARE TO BE POSITIONED WITH UNLEADED ON THE LEFT OF THE "A" SIDE OF THE DISPENSER FACE. SIDE "A" OF DISPENSERS ARE TO ALWAYS FACE CLOSEST TO STORE FRONT. IF THE DISPENSERS ARE PERPENDICULAR TO THE STOREFRONT, THE "A" SIDE WILL BE POSITIONED TO THE RIGHT, LOOKING TOWARDS THE STORE. 6 MPD'S 1-10,000 & 1-15,000 GAL. (1) 2 H.P. STP STAGE II "Y" FROM TANK TO FIRST BLENDER DISPENSER WITH 1 1/2" IHLL VAPOR RECOVERY PRIMARY PRODUCT LINE, AND USE 1 1/2" PRIMARY PRODUCT r TANK LINE TO THE REST OF THE BLENDER DISPENSERS. 2" GALV. STEEL. VENT INTERSTIC cXD PIPE & SUPPORT - NOTE: FOR HIGH VOLUME LOCATIONS USE 2-15,000 GALLON TANKS TO BE PAINTED STEEL VENT RISERS 'SOFT WHITE' OR AS AN ALTERNATIVE, USE 3- 15.,000 GALLON TANKS. — PLATE w 1 2 �G TANK MONITOR 2" GALV. 90 N MlN2 FG MIN FG SUB -PUMP 2 FG 'I 7/181 SCOPE S / G F, 1 1/2 y F h Irv, SCOP CLAMPS `\� 2„ FG (TYP.) UNLEADED ,� n - WRAP EXPOSED VENT RISER TANK I G\�P 12" BELOW CONCRETE WITH FLEX CONNECTOR 3M CATHODIC PROTECTION 1 TAPE _1. 2 (TYP.) NOTE: PREMIUM PRIOR TO PAINTING, TANK. ' ?" 2 ALL GALVANIZED METAL MUST BE PREPPED 8 TANks r� o ,M/N3 F.G FREE-STANDINNOT G GAVENT DETAIL LE OPPOSITERsIOKSOF LOCATED ON IOWA&,) LANDSt s pe NOTES: 1, VENT RISER TO EXTEND A MINIMUM OF 12' ABOVE GRADE WHEN LOCATED IN REMOTE AREA. 5 2. ALL STEEL PIPE & CLAMPS ABOVE GRADE PAINTED "SOFT WHITE PIPING SCHEMATIC (SIX ISLAND MPDS) PAINT FURNISHED BY 7 -ELEVEN TO THE CONTRACTOR. NOTE: SEE SITE PLAN FOR PUMP AND VENT LOCATIONS 6" THICK CONCRETE PAVING W/ #3'S @ 18" O.C. BOTH WAYS. APPLY CONCRETE ELECTRICAL SEALANT PER SPEC S:-- CONDUITS SPECIFIED FILL 0 0 0 °0 VAPOR RECOVERY LINE F113ERGLASS PIPING ro)��PRODUCT PIPING SECONDARY PIPING PRODUCT LINE 6"-3/8" PEAG AVEL BEDDING SECTION THRU PIPING TRENCH NOT To SCALE NOTE: IF CONDUIT OR WATER NEEDS TO CROSS FRENCH IT SHOULD DO SO PERPENDICULAR TO PRODUCT PIPE, UMP 2 FG UMP 4 4A 11ry y\�P 1 f� � FC 2 F� F. / OpE I:i SrORf SOF 5� 4" x 2" DOUBLE TAP BUSHING SLAVE TANK END 2" ELL 2" UNION THEN NIPPLE & 90' ELBOW 2" THREADED—� SEE NOTE - STEEL PIPE " U #3 BELOW 3/8 " COPPER FUNCTIONAL ELEMENT OF 2" FIBERGLASS PIPE W/3" SECONDARY CONTAINMENT PIPE 2" ENVIRON BALL VALVE #BSV-2020 OR EQUAL. MUST BE RATED FOR USE WITH ALCOHOL BLEND FUELS. 2" x 3/8" BUSHING FOR COPPER LINE 2" NIPPLE `ELECTRICAL CONDUIT SUBMERSIBLE + I ' 2" NIPPLE I 4", x 2" DOUBLE TAP.. BUSHING I II II 2" THREADED STEEL PIPE �I • II A U PRODUCT LINE 2" UNION THEN NIPPLE & 90' ELBOW \ I1 — 2"x2"x2" TEE h I I I I I I I I I in SUB PUMP END NOTES: 1. ALL FITTINGS TO BE CONTAINED INSIDE RISER. 2. SLOPE`TO TURBINE SIDE. 3. ENVIRON FLEXIBLE ENTRY BOOTS (PART NO. FEB -6300) AT SIPHON PENETRATIONS, WITH 3•X'2 RUBBER REDUCER BOOT (ENVIRON NO. RRB-3030) ON SIPHON SIDE & A 3'X"2 RUBBER TEST REDUCER (ENVIRON NO. RTR-3020) ON THE STP SIDE. SIPHON DETAIL NOT TO SCALE NOTE: SIPHON TO BE USED FOR MANIFOLDING OF TWO REGULAR 10,000 GALLON TANKS AT LOCATIONS WHERE THREE 10,000 GALLON TANKS ARE USED (1-10,000 PREMIUM & 2-10,000 REGULAR) NOTE: ALL SUMPS TO BE WATER TESTED NOTE: FOR VAPOR VAC INSTALLATION, STAGE II VAPOR RECOVERY LINE SHALL BE 2" FIBERGLASS PIPE WHEN THERE ARE TWO DISPENSERS OR LESS, AND 3" FIBERGLASS PIPE WHEN THERE ARE THREE DISPENSERS OR MORE, GENERAL NOTES 1, PIPING TO BE TESTED UNDER PRESSURE DURING BACKFILL PROCEDURE TO ASSURE NO BREACH IN SYSTEM — CHECK OFTEN DURING BACKFILL AND COMPACTION. 2. STAGE II VAPOR RECOVERY PIPING TO BE PRESSURE TESTED FOR DECAY AND BLOCKAGE PRIOR TO BACKFILLING. 3. PIPING TO BE CHECKED FOR CONTINUOUS SLOPE BACK TO THE TANKS. 1� EQUIPMENT SCHEDULE ITEM DESCRIPTION MANUFACTURER, PART NO, FURN. BY 1 FLEX 2QPNNECBTOR MS TITEFLEX PART NO. 110165-242-0180 7-11 ENVIRON ISOLATION TUBE W/DONUT ENVIRON PART NO. FIT -3530, ITR -3020 7-11 2" VAPOR VENT CAP (VAPOR VAC) OPW PART NO. 523V-2253 7-11 O GEODUCT FLEXIBLE CONDUIT ENVIRON PART NO, GDP -4500-1 7-11 4A GEOFLEX—D SUPPLY PIPING ENVIRON PART NO. GFP-2150 7-11 O 3" FIBERGLASS PIPE RED THREAD II OR AMERON G.C. O 2" FIBERGLASS PIPE RED THREAD II OR AMERON G.C. O 12" MANHOLE ASSEMBLY OPW PART NO. 104FG-1200 7-11 O 4" X 4" X 3" X 2" EXTRACTOR ENVIRON PART N0, VEF-4432 7-11 O9 GEOTECH MATERIAL SEE SPEC. SECT. III 2.2 7-11 NOTE: ALL SUMPS TO BE WATER TESTED NOTE: FOR VAPOR VAC INSTALLATION, STAGE II VAPOR RECOVERY LINE SHALL BE 2" FIBERGLASS PIPE WHEN THERE ARE TWO DISPENSERS OR LESS, AND 3" FIBERGLASS PIPE WHEN THERE ARE THREE DISPENSERS OR MORE, GENERAL NOTES 1, PIPING TO BE TESTED UNDER PRESSURE DURING BACKFILL PROCEDURE TO ASSURE NO BREACH IN SYSTEM — CHECK OFTEN DURING BACKFILL AND COMPACTION. 2. STAGE II VAPOR RECOVERY PIPING TO BE PRESSURE TESTED FOR DECAY AND BLOCKAGE PRIOR TO BACKFILLING. 3. PIPING TO BE CHECKED FOR CONTINUOUS SLOPE BACK TO THE TANKS. 1�