Laserfiche WebLink
i • <br /> UUULC Listed Red Thread® II A Piping System <br /> RED THREAD IIA PIPING <br /> RED THREAD IIA Primary Piping RED THREAD IIA Secondary Containment Piping <br /> Nam.Pipe Pipe Nom.Pipe Pipe <br /> Size Part Length Size Part Length <br /> (In.1mm) Number (ft.) (In./mm) Number (ft.) <br /> 2 50 011020-069-1 15 3 80 011030-069.4 15 <br /> 2 50 011020-069-2 22-25 3 80 011030-069-5 22-25 <br /> 2 50 011020-069-3 26-30 3 80 011030-069-6 26-30 <br /> 3 80 011030-069-1 15 4 100 011040-077-5 15 <br /> 3 80 011030-069-2 22-25 4 100 011040-069-5 22-25 <br /> 3 80 011030-069-3 26-30 4 100 011040-077-6 26-30 <br /> 4 100 011040-071-1 '15 6 1150 011060-120-5 15 <br /> 4 100 011040-069-2 22-25 6 150 011060-120-4 22-25 <br /> 4 100 011040-071-3 26-30 6 150 011060-120-6 26-30 <br /> DIMENSIONAL DATA <br /> Nominal Nominal Mill <br /> Pipe Nominal Nominal Wall Nominal Pressure/ Test External Pressure <br /> Size I.D. O.D. Thickness Weight Temperature Pressure Max.Rating(psig/MPa) <br /> (in.fmm) (10m m) (inimm) (In1mm) (IbL1ft.hsg-m) Max.Rating (psig/MPa) 75°F/24°C 150°F/66°C <br /> 2 2,235 2.375 .070 0.5 250 psig @ 150°F 375 85 80 <br /> 50 57 tl 1 1.78 0.74 1 72 MPa @ 66°C 2 59 1W55 <br /> 3 3.360 3.500 .070 0.7 175 psig @ 150°F 300 36 34 <br /> 80 85 90 2 54 1 04 1 21 MPa @ 66°C 2 07 23 <br /> 4 4.360 4.560 .085 1.2 125 psig @ 150°F 265 34 30 <br /> 100 111 1 I rd 2 16 1 79 0.86 MPa @ 66°C. 1 83 _. 21 <br /> 6 6.408 6 678 .135 2.4 NA 265 22 20 <br /> 150 163 1 7 n 34.3 3.51 NA 1 83 .15 14 <br /> TYPICAL PHYSICAL PROPER11ESM <br /> PROPERTY RED FHRP-AD°IIA PI a Bending Radius,Minimum <br /> psi 75°F MPa @ 24°C psi @ 160°F MPa 66"C Nominal <br /> P � � PIpe5lze 3" 4" 6" <br /> Ax al Tensile(ASTM D2105) inches <br /> Ultimate Stress 10,300 71 0 8,200 56.5 <br /> Design Stress 2,575 17.8 2,050 14.1 Ft. 75 110 140 204 <br /> Modulus of Elasticity 1.82x 106 12548 1.42 x 104 9791 <br /> Awal Compression(ASTM D695) m 21 3 <br /> 33,300 230.0 25,600 177,0 <br /> Ultimate Stress 8,300 57.2 6,400 44.1 <br /> Design Stress 1.26 x 106 8687 .89 x 104 6136 <br /> Modulus of Elasticity <br /> (1) A1lvalues except pressure-temperature <br /> Beam Bending(SFPTM) 159 0 19,200 132.0 maximum rating are nominalvalues.Tolerances or <br /> Ultimate Stress 23,000 maximumlminimum limits can be obtained from Smith <br /> Design Stress() 2,930 20.0 2,400 16.5 Fibercast <br /> Modulus of Elastic/ 2.18 k 104 15531 1 70 x 106 11721 <br /> Elasticity (2) All sixes can accept full vacuum pressures at <br /> (Lang Term per ASTM D2925) maximum temperature ratings. <br /> (3) Ultimate and allowable design stresses are <br /> Hydrostatic Burst(ASTM D1599) based on minimum reinforced wall thickness.Pipe is <br /> Ultimate Hoop 34,000 '2;q 39,200 '1171 manufactured in compliance with ASPM D29!i <br /> Tensile Stress (4) Design bending stress is 118 1ultimate to <br /> 2"-3" 2"&3" 2°$3" 2 3 account for combined stress(i.e.bending and <br /> Hydrostatic Design(ASTM D2992) pressure). <br /> Procedure A 9,410°1 64.9F° 7,4000 510 (5) Design stressis based on longterm cyclic fatigue <br /> Cyclic 150 x 106 4'-6" 4"-5' 4"-6" 4"-6" data using ASTM D2992 test method.However,all <br /> Cycles 13,0400 81.90 10,450 72 1 testing is not complete attime of printing. <br /> (6) For RED THREAD IlA p ipe the hydrostatic <br /> Coefficient of Linear 0.88 x 10`in lin!°F <br /> Thermal Expansion SFPTM 1.56 x 10$rrrnlrri-VC cyclic design stress was determined at 750°and <br /> p ( ) 2D0°F,per ASTM 02992 Procedure A-Based on this <br /> data,the extrapolated value at 75°F is 13D30 psi <br /> Specific Gravity 1.8 (1) For RED THREAD 11A pipe the hydrostatic cyclic <br /> Flew Factor design stress was determined at 75°and 2D0°F,per <br /> Hazen-Williams Coefficient 150 ASTM D2992 Procedure A Based an this data,the <br /> extrapolated value at 150°F is 7,4W psi. <br /> 4 <br />