Laserfiche WebLink
B667304 to • <br /> FLASH POINT LEL UEL FLAMMABILITY CLASSIFICATION <br /> Not Applicable N.A. N.A. Not Applicable <br /> EXTINGUISHING MEDIA <br /> Carbon Dioxide, Dry Chemical, Alcohol Foam <br /> UNUSUAL FIRE AND EXPLOSION HAZARDS <br /> Closed containers may explode(due to the build-up of pressure)when exposed to extreme heat. <br /> During emergency conditions overexposure to decomposition products may cause a health hazard. Symptoms may not be immediately <br /> apparent. Obtain medical attention. <br /> SPECIAL FIRE FIGHTING PROCEDURES <br /> Full protective equipment including self-contained breathing apparatus should be used. <br /> Water spray may be ineffective. If water is used,fog nozzles are preferable.Water may be used to cool dosed containers to prevent pressure <br /> build-up and possible autcignition or explosion when exposed to extreme heat. <br /> SECTION 6-ACCIDENTAL RELEASE MEASURES <br /> STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED <br /> •Remove all sources of ignition. Ventilate the area <br /> •Remove with inert absorbent. <br /> SECTION 7 NDLING AND STORAGE <br /> STORAGE CATEGORY <br /> Not Applicable <br /> PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE <br /> Keep container closed when not in use.Transfer only to approved containers with complete and appropriate labeling. Do not take internally. <br /> Keep out of the reach of children. <br /> SECTION 81-EXPOSURE CONTROLS/PERSONAL PROTECTION <br /> PRECAUTIONS TO BE TAKEN IN USE <br /> Use only with adequate ventilation. <br /> Avoid contact with skin and eyes.Avoid breathing vapor and spray mist. <br /> Wash hands after using. <br /> This coating may contain materials classified as nuisance particulates(listed 'as Dust"in Section 2)which may be present at hazardous levels <br /> only during sanding or abrading of the dried film. If no specific dusts are listed in Section 2,the applicable limits for nuisance dusts are <br /> ACGIH TLV 10 mg/m3 (total dust),3 mg/m3(respirable fraction),OSHA PEL 15 mg/m3(total dust), 5 mg/m3(respirable fraction). <br /> VENTILATION <br /> Local exhaust preferable.General exhaust acceptable if the exposure to materials in Section 2 is maintained below applicable exposure limits. <br /> Refer to OSHA Standards 1910.94, 1910.107, 1910.108. <br /> RESPIRATORY PROTECTION <br /> If personal exposure cannot be controlled below applicable limits by ventilation,wear a properly fitted organic vapor/particulate respirator <br /> approved by NIOS W MSHA for protection against materials in Section 2. <br /> When sandi ng or abrading the dried film, wear a dust/mist respirator approved by NIOSWMSHA for dust which may be generated from this <br /> product,underlying paint,or the abrasive. <br /> PROTECTIVE GLOVES <br /> Wear gloves which are recommended by glove supplier for protection against materials in Section 2. <br /> EYE PROTECTION <br /> Wear safety spectacles with unperforated sideshields. <br /> SECTION 9-PHYSICAL AND CHEMICAL PROPERTIES <br /> PRODUCT WEIGHT 8.76 Wgal 1049 g/I <br /> SPECIFIC GRAVITY 1.05 <br /> BOILING POINT 212-500°F 100-260°C <br /> MELTING POINT Not Available <br /> VOLATILE VOLUME 61% <br /> EVAPORATION RATE Slower than ether <br /> VAPOR DENSITY Heavier than air <br /> SOLUBILITY IN WATER N.A. <br /> PH 9.0 <br /> VOLATILE ORGANIC COMPOUNDS(VOC Theoretical-As Packaged) <br /> 1.50 lbrgal 179 gA Less Water and Federally Exempt Solvents <br /> 0.71 Ib/gal 85 9A Emitted VOC <br /> page 2 of 4 <br />