COMPLIANCE INFO_PRE 2019 - Laserfiche WebLink

Home Browse Search

2) Insert aerosol can,ng sl F.Erie south ince h EROS �T� @ MAINTENANCE.INTE�TAt�T(',E. � i'° -m�..� the Aerosoly�housing sleeve;so that#hE3 Lll: Ll vLY tY111,11 V 1'f 1V L.,l shoulder of_the can re"sis on the internal. in gasket.tae sure to remove cap fro Ylfhen.Aeroso[+ir'operatlons.concludei inspect the gasket and seals for a aerosol Can prior to inserlion. deterioration of contamin8tion and replace or remedy as neCes$ary. 3j* Lower diding lop plate oder the bottorn Puncture.Pin:This pin should be inspected and cleaned after punctu"ing of the inverted can antl firmly:engage 500 cans.While Aeresoiva unit is attached to the collection drum remove against plastic sleeva.Tighten.thelock #50.10 Large CleVis Pin allov�ing the entire handle and puncture pin to be knoll on the side of the housing.Tighten � removed from Aernsal+lr'Housing. sealing knob-to further depress aerosol _72 _ "" Can to Into silicon gasket. • Ins ect the 2 Oris for deterioration and visible wear.Remove worn 4- °' l 4) 20013005eries Cans,Push handle rings afld replace as necessary. down firmly until taihp[Blely lie reseed and hold in face while Apply liberal coatis of Lithium rease rior to assembly . .� . -. P p g .. 9 P Y can releases initiatpressureand Gasket Replacement:Visually ins bet the gasket daily riorto each use.If = Contents.Allow the contents of the P y P 9 y p can to drain lrrto the collection druin the gasket is cracked or deteriorated-to the ppint that it no longer provides • (about 2t)setond§). an adequate seal, replace it by holding the gasket and lifting out_To insert 5} When the aerosol cari's.contents have the new gasket into the housing,push downward with the#5018 Poly Sleeve been completely discharged(about snapping into place. 20 secoinds or when Can contents are till�; • Cheek-Valve Assen'ibly:This assembly should be inspected after punctur ;r I obviously discharged),tum sealing knob t `3 taunter-clockwise 3 rotations,unfasten ing 1,000 cans.Remove Aerosch0 unit from collection drum and inspect for f`r/ ''•l i t the lock knob and lilt the can to the brim seal quality..Clean area thoroughly inside and out.Apply(3)wraps of Teflon Z. of the Aerosnl,+3 housing Some residual tape to 2°threads that attach to the collection drum prior to installation. ra i l fluid rhay be entrapped between the lip f.` of the can and the linte(s)created by • Aerosols"Puncturing Unit,The entire unit should be wiped down after f£ +1,•,�' the puncturing device.Tip the can each use.Clean the entire unit daily and bpply a liberal oaating of Lithium x'- ailow the residual to discharge into the grease t0 all moving rts_ g pa s unit.A r3 rag maybe used to remove any` = 9 .:.. ... ... . ��,.� r��`- ;.;;,:, �•-�-- remaining residual from arouhd the can. I. Reinove the tat!from lhe then to 66nS#5016EX uncmie hi foiltnv thesd eir sliding lop plate to rest on plastic sleeve inaiiFcenauce prpceduieabe-e.Note:Insei�Cpiri as to seal the collection drum,and manage pictured to the left and below. l the empty can approtiriateiy 6) Continuously morlRor.the colerriietric indicator to determine when the carbon -in the carbon canister is approaching saturation:11 the indicator indicates that Baling Fo_b the carbon is saturated,discontinue •,�`��,a t puncturing and replace the carbon canister. ►soli t 7) When AsrosohPoperations are l` complete,the unit should be locked out to avoid unauthorized use.If the collection drum is more than 70%full, I, seciire the.drurn and do not return it to asei use.The unit may also be secured in o Po'm soisx dwrePbdLhC-eiogs cv i = sb:9�xb place by Inserting;i padlock to prevent unauthorized use.The padlock is. >. inserted in the through=hole located on C comss_v_�o,ru the slide bar. U. - N r� . 00 O O _ - O N $ 9.