COMPLIANCE INFO_PRE 2019 - Laserfiche WebLink

Home Browse Search

2) Insert aerosol can,NOZZLE END DOWN,into ^^�p TT`` s -- - the Aerosold'housing sleave,so that the L�1.R�S�Ll� NILM1V 11;NA CE: rrt shoulder of the can rests on the internal gasket,Be sure to rerrmove cap from When Aerosolv°operations conclude,inspect the gasket and seals for �- aerosol can prior to insertion. deterioration or contamination and replace or remedy as necessary. 3) Lower sliding lop plate over the bottom Puncture Pin:This pin should be inspected and cleaned after punctuing rMn =} of the inverted can and firmly engage500 cans.White Aerosol'unit is attached to the collection drum,.remove against plastic sleeve.Tighten the lock #5010 Large Clovis Pin allowing the entire handle and puncture pin to be knob on the side of the housing.Tighten removed from Aerosolv ap e housing. „ti.•, „y,,.,_•- sealing knob to further depress aerosol 9 can to internal silicon gasket- Inspect g Inspect the(2)0-rings for deterioration and visible wear.Remove worn o o = 4) 200!300 series Cans.-Push handle rings and replace as necessary. N down firmly unfit completely �-•-s{�r v� depressed and hold in place while • Apply liberal coating of Lithium grease prior to assembly. can releases initial pressure and Gasket Replacement:Visually inspect the gasket daily prior to each use.If contents,Allow the contents of the • can to drain into the collection drum the gasket is cracked or deteriorated to the point that it no longer provides (about 20 seconds), an adequate seal, replace it by holding the gasket and lifting out.To insert ^ the new asket into the housing,push downward with the 95019 Poly Sleeve ^ b) When the aerosol can's contents have g g�p Y been completely discharged(about snapping into place. 20 seconds or when can oonlents are`� 'I obviously discharged),turn sealing knob Check Valve Assembly:This assembly should be inspected after punctur- s counter clockwise 3 rotations;unfasten ing 1,000 cans.Remove Aerosolv`unit from collection drum and inspect for the lock knob and lilt the can to the brim seal quality.Clean area thoroughly Inside and out.Apply 3 wraps of Teflon Q Y• g Y PP_YZ ) p of the Aerosoly�housin Some residual tape to 2"threads that attach to the collection drum prior to installation. Iluid may be enlrapped between the lip P P of the can and the hole(s)created by AerosolvO Puncturing Unit:The entire unit should be wiped down after � the puncturing device.Tip the can to each use.Clean the entire unit daily and apply a liberal coating of Lithium allow the residual to dischare into the l r F g grease to all moving parts. unit.A rag may be used to remove any remaining residual from around the can. } Remove the can from the housing, lower �hlten replacing#5016EX puncture pin Follow the I sliding lop plate to rest On plastic sleevemaintenance procedure aborti.Note:Insert pin as `•'' _,., ; to seal the collection drum,and manage pictured to rhe tett and below. the empty can appropriately. 6) Continuously monitor the colormetric indicator to determine when the carbon in the carbon canister is approaching saturation. If the Indicator indicates that "�U �, �aalrq Knnb the carbon is saturated,discontinue puncturing and reptace the carbon r - canister_ am;� 7) When AerosolO operations ark r;n"n sinkv l i complete;the unit should be locked I =�iasrru J + out to avoid unauthorized use.If the ; ±� collection drurn Is more than 701/6 full, I i secure the drum and do trot return it to Me, , use.The unit may also be secured in 0IMS 10ME c n:hrer5iPM-Mga N :d • r: � _ We K,,,S place by inserting a padlock to prevent unauthorized use.The padlock is a inserted in the through-hole located on F Eqi nafo:ftFe the slide bar. I1 VM 0-A k1ive Ommt4f 00 CD _1 N 8 9 .