INSTALL INSTALL PLAN 1998 - Laserfiche WebLink

Home Browse Search

48' Ir NOTE' HIGH HOSE RETRACTOR 1. SUPREME NOZZLE MUST ALWAYS BE ON THE LEFT. 2. PRODUCT PIPING (HARD) MUST ALWAYS PENETRATE THE DISPENSER SUMP FROM THE OPPOSITE SIDE OF THE HOSE BREAKAWAY 68 CONDUIT. 3. PLUG ON VAPOR SHEAR VALVE MUST BE ACCESSIBLE. 4. USE RIGID PIPE (INSTEAD OF HOSE) FOR VAPOR INSIDE ALL DISPENSERS. 5. INSTALL VAPOR SHEAR SUPPORT FROM TOP OF SHEAR VALVE TO DISPENSER. DISPENSER g OR 67 6. PULL BACK REDUCERS IN DISPENSER BOXES AFTER SECONDARY PIPE HAS BEEN TESTED. EXPLOSION PROOF JUNCTION BOX c DO e FILTER o SEAL OFF 1 1/2"0 SCH. 40 BLACK IRON PIPE RISER PIPE CAP NTH HOLE FOR i 1 2' N.P.T. INLET UNION CONTAINMENT PROBE WIRE DISPENSER NOZZLE 68 (BY DISPENSER MFG.) SEAL ALL OPENINGS WATER TIGHT p DISPENSER NOZZLE SWIVEL FILTER CHANGE TRIP TRAY SLOPE CONCRETE (BY DISPENSER MFG.) _ 1 1/2' PER FOOT TESTING: DPW DUAL POPPET IMPACT VALVE _ AWAY FROM (SHEAR SECTION TO BE FLUSH DISPENSER MID.) HATH TOP OF DISPENSER ISLAND) 71 • 4 - 'e4, 4 1. FILL DISPENSER SUMP WITH WATER UP TO HIGHEST PENETRATION. C' . •' • • 4 REMOVE WATER WHEN DIRECTED BY CHEVRON PROJECT MANAGER. .d ' .i. " , ' : . 4a ' • e NOTE, • ° . • �. ' 2. WHEN TESTING PRODUCT LINES, INSTALL STEEL CAP ON OPEN 4 1 TOP HOSE MOUNT AVAILABLE. MOUNT. I � • .. . , .4. SHEAR VALVES TO AVOID DAMAGE TO THE VALVE, 3/4' P.V.C. PUMP OUT PIPE • STABILIZER BAR 73 2.SUPREME SIDE OF DISPENSER MUST ALWAYS BE ON THE LEFT. WITH THREADED FITRNG BRACKET EXTENSION F.R.P. DISPENSER CONTAINMENT SYSTEM 89 SUMP FOR CONDUIT IRON BOOT 99 1 DISPENSER ELEVATION — DRESSER WAYNE XV590 sfi 45' BLACK IRON ELBOW 1' CONDUIT TO CONTROL I1/2' PANEL (POWER) 1' CONDUIT TO PANEL (DATA) CONTROL SIDE 'B' (PRODUCT AND VAPOR PIPING SIDE) o _ I 3/4' CONDUIT TO CONTROL 48' PANEL (SPEAKER) 24" 24" 3/4' CONDUIT FOR CONTAINMENT 0 2 1[2' MINIMUM CLEARANCE BOX PROBE TO MONITOR PANEL 21" 21° BE7TWWEEEN FITTING do PIPE I BRACKET 9" 10 1/2" 10 1/2" 9" 2"0 F.R.P. PIPE 18 (DO NOT PENETRATE SUMP) 3/4" x 1 1/2' � Tr 3" P.V.C. PIPE OPEN AT BOTTOM. SLOTS �8) 2 1/2" I 18" VID ATTACH TO CONTAINMENT BOX PROD 3'0 F.R.P. PIPE 19 AS NEEDED FOR SUPPORT. FOR' ANCHOR — DISCRIMINATING SENSOR _ BOLTS 6 1/2" SUMP PENETRATION BOOT 0 1 1/2"M SWIVEL x YF x 24" MINIMUM FLEXIBLE CONNECTOR, ALTERNATE — CLEARANCE3" TO 2' REDUCER BOOT FLEXIBLE CONNECTOR WITH ELBOW 1/2" NPT 3 3/e" BETWEENIWITH TEST PORT NOTE, CONDUIT I 10 3/8° � (ROLL BACK BOOT AFTER TESTING) 74 USE APPROVED NON—HARDENING (SPEAKER OPT.) r 2 4 o JOINT COMPOUND - FOR THREADED CONNECTIONS. M — — {� +'— — —}— _ tv n 4 1 4, N PRODUCT 2" BELL h MALE F.R.P. p — — THREADED ADAPTOR ao I I Y.. 1' N.P.T. VAPOR 1 1/2' N.P.T. INLET (2) 13 1/2" RECOVERY OUTLET NOTE: X SIDE 'As 1' N.P.T. CONDUIT 1. CONTRACTOR TO FIELD VERIFY DISPENSER BASE DIMENSIONS. (CONDUIT SIDE) 2.PRODUCT ORDER SHOWN IS TYPICAL, NO OTHER VARIATIONS ARE ACCEPTABLE. DISPENSER GENERAL CONTRACTOR TO PROVIDE 2 DISPENSER BASE — DRESSER WAYNE XVW0 RIGID PIPING TO EACH VAPOR RECOVERY MANIFOLD 1 1/2' x V DPW DUAL POPPET VAPOR SHUTOFF VALVE (SHEAR SECTION TO BE FLUSH WITH TOP OF DISPENSER ISLAND) 72 a . •. .4 9 • 45' BLACK IRON ELBOW 6" MINIMUM PEA GRAVEL COVER OVER F.R.P. PIPE i 1 1/2"M SWIVEL x 2"FX 24" FLEXIBLE CONNECTOR NOSE, f USE APPROVED NON—HARDENING , JOINT COMPOUND FOR THREADED CONNECTIONS. 2'0 F.R.P. VAPOR RECOVERY PIPE 20 2' BELL & MALE F.R.P. SUMP PENETRATION BOOT 96 THREADED ADAPTOR Chevron U.S.A. Inc. ("Chevron) owns the copyright rights to the design of the herein described fueling ; system as embodied in any tangible or electronic medium of expression Including all building NOTE; designs, architectural plans and drawings. The copyrighted material Includes the overall form as well as 1. MOUNT VAPOR SHUTOFF VALVE USING PHIL—PTE the arrangement and composition of space, and elements In the design, but does not include Individual VAPOR IMPACT VALVE SUPPORT KIT. VAPOR RECOVERY standard features. Anyone who wishes to copy, distribute or sell this drawing or any derivative works based hereon must have the prior written consent of Chevron, except for copies made for the sole purpose of preparing construction drawings for Chevron branded facilities and all such copies shall be Q returned to Chevron upon request. ©1995 Chevron U.S.A. Inc. All rights reserved. The drawings, calculations, and any specific reference to equipment, materials or components. W if included herein, are generic and not designed for site specific applications. Chevron does not warrant ¢r or guaranty the accuracy, completeness, merchantabllty, Intended use or applicability of such drawings, calculations, and any referenced equipment, materials or components, to the requirements or Q 3 needs of your site or local area. Consult a registered architect or professional engineer to determine any alta specific design, applicability, accessibility, building code, municipal requirements and any and DISPENSER CONNECTION AND PIPING (HARD) all applicable federal, state and local statutes, rules and regulations which may affect your site. NO SCALE Chevron does not provide these services. LL Q DIBPBJBBi BUM'AND PPM DETAILS = Chevron - Marketing Revklar SCALS 1/4'-f-0' DATB 02/27/98 DR CH. APP. SHEET F-6