COMPLIANCE INFO 2004 - 2007 - Laserfiche WebLink

Home Browse Search

`Mar .24. 2005"10; 13AM"y°W vht Environmental 832-5152 w rcrt a No.8048 P. 18 10 Installation Instructions publeetiore P¢BI-Solo environ Vn Flexible EntryBoots Issue pee: 05.05-01 sup.rxed4a, oe-,o o, Flexible Entry Blkots Those one-piece rubber boots are designed to eaal pipe and conduit entries for both flat and curved surfaces. For proper installation,the appropriate sled fabrication template should be used for accurate hole drilling. The recommended sizes of hole aawa must be used for the given flexible Entry boot size, step#1 Step#2 Locale the canter entry point In Drill out the entry boot opening the flat wan-action of the sump " by using the appropriate size hole bass and drill a 5116"hole. saw. After drilling out opening, Install the Fdtry Boot remplere clean rough edges with a razor to the sump base well using a knife or daburing tool. 114"bolt and fall. Drill out one Hnle fie, ftsxibla EM goon hole of the appropriate bolt holy: rY circle for the size boot to be 1.314• small proala FEe.3e75 installed using the same 6/16" 24/w i{g op 506100. EB-3073157 drill bit. Insert a second 1/4" 3' FE&5150 bolt and nut through this hole to 41w FES-0196,0200,woo aeoure the template. Continue 5.12' FE11-7350,7390,7400 to drill the remaining holes of 5-12' sae-7400 the bolt hole patter_ After 5117• 613841515,45z0,4530, drilling,remove the template Sabre Sew 745) o from the sump base wall Step#3 Step#4 Install the entry boot from out. Using the proper nut driver. aide the sump by Inserting the tighten all 01 the nuts evenly and studs through the holt holes. firmly. To prevent deforming From the inside of the sump, boots,do not over tighten nuts. install the compression ring If a torquo wrench is used,the over the studs and install nuts setting should be 60 In.lbs. by hand, Step#6 Angled Entries Insert the appropriate sized pipe The floxible entry boot is or condelt Into the flexible boot designed to permit angled pipe from the outside of the sump. or conduit entries up to 15-off After the pipe or conduit has the centerline Angles greater been positioned,Inatall the than Wel ld prevent the boot band clamp around the boot fmm%waling around the pipe and tighten to or conduit,and will void the 36 in.lbs. productwarmnty. fiberglass surfaces WARNING Flexible Entry Bouts may be Installed on round surfaces which Keep all fiborgless*leaning solvents away from boots. have a dismeter greater than 301. These types of solvents could cause severe damaga. The installatlon procedures aro the same an described above except extra rare shall be taker, to pprcp*rly hand send the surface to bo bonded.Make sura all raised sections of FAP are minimized and remove alreharp edges.The 5110' IMPORTANT bolt holes should be made slightly The recommended hole saw size must always be used larger atter Initial drilling.This can for proper installation of the flexibN Entry 600tand be accomplished from aid by mile in the Solt bitfrom girt¢to side in ttreh mefntafn the product warranty. bolt hole akar the Entry Boot Tem- plate has been removed. Tighten A hydrostatic test must be performed to down each nut in Reagan so the ensure a positive Boal, boot flange and compression ring can evenly conform to the rounded surface and schleve a positive Real, Environ Products,Inc. 3250 US 70 Business West Smithfield,NO 27577 a Tel: (919)359-34DO Fax: (919)359-3687 • Customer Service: (800)833-1883 • www,envprodtict.com• 0 Copyright 2004