Laserfiche WebLink
Nar•25. 20066 4:53PM1916Wr ' ht Environme;ta1, 832-6152 IareFFR ;�. No P• 2E el <br /> 03/25/2005 15:46 FAX 530 654 7740 DIVERSIFIED <br /> Vic. i... <br /> warnings: ��). �egti ir+eta)ia;ir:9n�naeructie+re <br /> izj paaa �n �� S,Fleet <br /> Prior to installation: 43) Use appropriate eye and slob A3te�n <br /> Strep 1 Step 2 - prepare Sump Surfaco : CO <br /> t) Where possible run pipe so as to penetrate the -�- <br /> sump perpendicular to sump surface. I <br /> 1) Olean dry all surfaces " <br /> 2) Sand fiberglass sumps light9l�}po <br /> 2) Where penetrations must enter the sump r5' remove gla2e ?T'.c %0 <br /> Z <br /> rolling style bulkheads are recommended. 3) Sand down all uneven sump yy es <br /> 3) Where sump penetrations are greater than 15% 4) Select threaded or studded bulkilkad <br /> use studded bulk- style. For studded bilkheads go to back <br /> heeds with rolling ?.: page, Step 3-Studded <br /> style reducers. See <br /> installation instruc- Note: Oocaalonally extra product exists causing <br /> Ilona for studded Inconsistam wall thickness. It is common to <br /> bulkheads, find this problem near seams in the sump. <br /> Send down uneven areas until a consistent <br /> wall thickness Is available for the entire sealing <br /> area of the bulkhead. <br /> Step 3 Step 4 <br /> orlil hole pattern for the required 1) install bulkhead body through sump wall <br /> number of entries: 2) Apply Weaver Seal-Tice to O ring pocket of <br /> bulkhead nut. <br /> Threaded hole Min spacing 3) Apply Seal-rite to face of seat (for double <br /> Style saw. batweencentera ended fittings apply Seal-Tits to outside <br /> B2 2" 3" seal in the same manner). <br /> B3 3' 4.5' <br /> B5 5' T' <br /> f <br /> Outalde of <br /> sump01 <br /> _, <br /> Step 5 Step 6 <br /> 1) Thread nut onto body or hold nut and thread 1) Install terminating fittings on bulkhead <br /> body into nut. Tighten bulkhead until snug. 2) Push pipe through boots <br /> Do not exceed the following torque specifications: 3) Tighten band clamps on all <br /> B2 20 Witt surfaces. Do not exceed 60 i1. <br /> B3 20 in/lb Ib. torque <br /> B5 25 In/Ib 4) Duplicate process for <br /> Be 60 fob outside boot on jmdE i V_ <br /> Use Weaver manufactured double sided fittings <br /> wrench for e6 bulkhead. <br /> Water pump pliers and M <br /> sockets may be used on <br /> 82, 83 and B5 bulkheads. ---------------- <br /> ' q <br /> Materials Needed: Hole Saw, additional Seal-Tile for uneven surfaces. <br /> Rev4ftU4 , Diversified Prod=&M%LLC-552JBMW maIryrvllland.--Orovilie,CA95965•uvww.divarrifiedprodndsmCg.cum 5im.2-3 <br /> Cent,Cat, Adsmaistratlyc Pk$30.534-3966,Fx:530.533-3361,Order Fairy 530-534-7404•F!r.-a56-534-7404 <br />