Laserfiche WebLink
DISPENSER <br /> STABILIZING BAR <br /> e' <br /> SPRING NUT <br /> SUMP SENSOR J-BOX 2-IN-1 SENSOR BOX <br /> DISPENSER SUMP <br /> FRAME .. <br /> PRODUCT SHEAR ' <br /> °i <br /> VALVE : . .. c .........._. <br /> ANCHOR BOLT a r c c h i t e c t u r e <br /> ELBY CAPPED ELBOW L/ MOUNTING FLANGES e n g i n e e r i n g <br /> (TYP.) DISPENSER JUNCTION ANCHOR BOLTS L��Pi & <br /> BOX TYP. 6"THICK RIVE SLAB MINI HYDROSTATIC SUMP ssociates, <br /> (TYP.) ANNULAR SENSOR W/BRINE <br /> RESERVOIR WITH SIGHT GLASS (TYP.) 867 Pacific Street, Suite 120 <br /> San Luis Obispo,CA 93401 <br /> ° ° ph 805.540.5240 <br /> CONDUITS ROUTED fax 805.540.5241 <br /> DISPENSER SUMP FRAME <br /> SEAL-OFF (TYP.) ° THROUGH SLOTS IN www.LHBassoc.com <br /> SUMP FRAME (TYP.) <br /> RUN CONDUITS THROUGH DISPENSER UNDER DISPENSER 1-1/2" MxMS FLEX CONNECTOR (TYP) <br /> "BRAVO" <br /> HOLES IN DISPENSER SUMPQ�pFESS/O <br /> DOUBLE WALL FRP 30" DEEP <br /> FRAME"A"SIDE OR"B" CONTAINMENT SUMP S BF <br /> SIDE O.K. (TYP) <br /> SENSOR MOUNTING w o: No. 78916 A Z <br /> DISPENSER SENSOR MOUNTING KIT of e <br /> MONITORING CONDUIT HANGER KIT (TYP.) LIQUID SENSOR <br /> O 3"OVER 2" D.W. Op CA �F <br /> DISPENSER POWERSUMP MONITOR FRP PRODUCT PIPING <br /> & DATA CONDUIT LIQUID SENSOR <br /> CONSULTANTS <br /> 1-1/2"90' ELBOW (TYP) 3 <br /> 1-1/2"x2" BELLxFEMALE FRP ADAPTER (TYP) <br /> NOV FIBERGLASS D.W. CUFF <br /> 2" FRP TERMINATION FITTING WITH TEST ENTRY <br /> PORT AND VACUUM TUBING ROUTED TO <br /> VAC SENSOR ASSEMBLY (TYP.) <br /> CONDUIT ROUTING DETAIL PRODUCT PIPING AT DISPENSER <br /> 3 SCALE N.T.S. SECTION SCALE NTS. <br /> DISPENSER VAPOR PRESSURE SENSOR (1 PER SITE) <br /> STABILIZING BAR <br /> SPRING NUT REVISIONS <br /> DISPENSER SUMP VAPOR FLOW SENSOR (1 PER DISPENSER) PLAN CHECK#16-3684 <br /> FRAME 1 07 DECEMBER 2016 <br /> 1"STREET 90°WITH 1" NPT NIPPLE ENGINEERING PLAN CHECK <br /> ANCHOR BOLT (SUPPLIED BY CONTRACTOR) zi #16-3684,3685 29 MARCH 2016 <br /> MOUNTING FLANGES VAPOR SHEARSJC EHD PLAN CHECK <br /> 3 VALVE 3 #SR0076222 8 NOVEMBER 2017 <br /> 6"THICK RIVE SLAB ANCHOR BOLTS <br /> ° o <br /> a ° SUBMITTAL DATES <br /> OWNER: <br /> UNDER DISPENSER 1-1/2" MxMS FLEX CONNECTOR (TYP.) 03/29/2016 <br /> "BRAVO" REG. AGENCIES <br /> DOUBLE WALL FRP 30" DEEP <br /> FLANGE W/1"NPT CONTAINMENT SUMP <br /> THREADED INLET O.T.B.: <br /> 1/2"x 1"THREADED -- <br /> MALE ADAPTOR INLET SCREEN <br /> VAPOR FLOW PROJECT NO. <br /> SENSOR CABLE TO JUNCTION 15-13-001 <br /> BOX 3"OVER 2" D.W. DRAWN BY: <br /> I"SHORT NIPPLE FRP VAPOR PIPING AFS <br /> ''r,------ <br /> 1"90°STREET OUTLET O-RING <br /> CHECKED BY: <br /> � JRB <br /> ELBOW FLANGE W/1"NPT <br /> STABILIZER ASSEMBLY THREADED OUTLET 1-1/2"90° ELBOW (OR TEE WHEN <br /> TOP of ISLAND r'PLUG CONNECTING TO ISD PRESSURE SENSOR) <br /> 1-1/2"x2" BELLxFEMALE FRP ADAPTER NOV FIBERGLASS D.W. CUFF <br /> ENTRY <br /> 2" FRP TERMINATION FITTING WITH TEST <br /> PORT AND VACUUM TUBING ROUTED TO NOTE: <br /> VAPOR SHEAR VALVE VAC SENSOR ASSEMBLY CONDUIT AND SENSORS NOT <br /> NOTES SHOWN IN THIS DETAIL FOR <br /> 1. (1)VAPOR FLOW SENSOR REQUIRED PER DISPENSER.SENSOR SHALL BE <br /> MOUNTED ABOVE SHEAR VALVE. CLARITY. <M <br /> W < <br /> W 6) <br /> ISD VAPOR FLOW SENSOR VAPOR PIPING AT DISPENSER 'U U) z <br /> 4 SCALE NTS 2 SECTION SCALE NTS O W Q <br /> J <br /> Z � 0 <br /> � Q <br /> oW <br /> CF) Q <br /> V <br /> VAPOR PRESSURE SENSOR <br /> CABLE TO JUNCTION <br /> MOUNT SENSOR TO DISPENSERS BOX <br /> INNER FRAME WITH SUPPLIED <br /> BRACKET <br /> PRESSURE SENSING 1/4"OD COPPER TUBING. <br /> PORT AVOID ANY TRAPS!(BY <br /> LID.. <br /> CONTRACTOR) a SHEET TITLE <br /> 1/4"TUBE W/114"NPT MALE M <br /> ADAPTER FITTING INTO TEE o <br /> FITTING.#CA68-4-4 <br /> CAP REDUCE THREADS FROM 1-1/2" PIPING INSTALL <br /> TO 114"WITH DOUBLE TAP <br /> BUSHING(S).APPLY APPROVED a DETAILS AT <br /> 2-WAY CALIBRATION PIPE DOPE AT ALL THREADS FOR N <br /> VALVE A TIGHT SEAL. v_ <br /> v <br /> PRODUCT <br /> DISPENSERS <br /> N <br /> U <br /> O <br /> VAPOR RETURN o <br /> BACK TO TANK `o <br /> U <br /> c <br /> NOTES `> <br /> L ONLY(1)VAPOR PRESSURE SENSING DEVICE REQUIRED PER SITE. t <br /> SENSOR SHALL BE MOUNTED AT ONLY DISPENSER LOCATED CLOSEST <br /> TO TANKS. <br /> 2. CONTRACTOR SHALL PITCH ALL 1/4"TUBING AS REQUIRED TO AVOID SHEET NO. <br /> ANY LIQUID TRAPS <br /> 0 <br /> VEEDER-ROOT ISD VAPOR PRESSURE N FS <br /> 5 '66 <br /> SENSOR CONNECTION SCALE NTS 16 <br /> i <br />