COMPLIANCE INFO_2006 - 2010 - Laserfiche WebLink

Home Browse Search

0 0 ffffCON 'v Franklin Fueling Systems TS-VFM Installation Guide This install guide provides necessary installation instructions for the mounting of the INCON Vapor Flow Meter inside a dispenser or inside a dispenser sump. Information regarding the cabling and the connection to the Tank Sentinel Console is found in the Tank Sentinel Installation Guide(pin 000-2150). All documentation relating to operability,maintenance,and testing of the Vapor Flow Meter is found in the Vapor Recovery Monitor Operator's Guide(pin 000-2058). Important: See the Vapor Recovery InstalllOperatom Manual or Tank Sentinel Installation Manual for Important Safety Messages. Required Tools Related Documents • Pipe joint tape(Teflon Tape) • 000-2058: Vapor Recovery Mondor Operators Guide • Pipe Wrench • 000-2150: Tank Sentinel Installation Guide-TS-5X)D(Series • Small screwdriver(terminal block connection) • 000-2142: Tank Sentinel Programming Guide-TS-5)=Series • Slip joint pliers(crimping splice connector) • 000-2151 : Tank Sentinel Operator's Guide-TS-5XXX Series Preoaration Only use approved pipe joint tape(Teflon Tape)for joints connecting to the Vapor Flow Meter. The use of non hardening,"pipe-dope,"thread sealant is strictly prohibited and will void the warranty. 1. Perform a site inspection.Determine how the Vapor Flow Meter will be installed.The preferred installation method for this.product is to install above the vapor shear valve. If there is not enough room between the vapor shear valve and the vapor pump,installation below the shear valve maybe needed. 2. If the Vapor Recovery equipment is going to be installed on an existing service station,verify that there is a run at intrinsically safe conduit going back to the console.Vapor Flow Meter wiring can share the same space with other intrinsically safe cables,but cannot be run with non-intrinsically safe cables. 3. Make sure that all contractor-supplied piping materials are compatible with California fuels and meet all local codes. Parts List and Materials Needed Table 1 -Above Shear Valve Table 2-Below Shear Valve r- - F-TIMM -' Vapor Flow Meter,TS-VFM INCON 1 Vapor Flow Meter,TS-VFM INCON 1 Sensor Installation Kit,020-1509 INCON 1 Sensor Installation Kit,020-1509 INCON 1 Weatherproof Junction Box Contractor 1 Weatherproof Junction Box Contractor 1 1.5"to 1"reducing bushingContractor 1. 1.5"pipe nipple Contractor. 2 1.5"to_"reducing bushing` Contractor 1 1.5"pipe union Contractor 1 1"pipe nipple Contractor 1 _"pipe nipple" Contractor 1 "-piping size is dependent on vapor piping size inside the dispenser.Typically the connection to a Healy VP1000 is a%"NPT. Thus,the bushing size will be Pipe Union Contractor 1 1.5"to 0.5". Installation Steps Above Shear Valve Below Shear Valve 1. Lock and tag out power to the dispenser and the console before 1. Lock and tag out power to the dispenser and the console before attempting attempting any work on the dispenser. any work on the dispenser. 2. Refer to Figure 1 for reference. 2. Refer to Figure 2 for reference. 3. Do not remove the protective raps on the Vapor Flow Meter until 3. Do not remove the protective caps on the Vapor Flow Meter until you are ready you are ready to thread the nipples into the Flow Meter. to thread the nipples into the Flow Meter. 4. Begin by connecting the two 1.5"to 1"reducing bushings to the 4. Begin by connecting two 1.5"NPT pipe nipples to the Vapor Flow Meter's Vapor Flow Meter's body.Be sure to use only Teflon tape when body.Be sure to use only Teflon tape when sealing these threads.Take special sealing these threads.Take special precaution not to let any precaution not to let any foreign material fall inside of the Vapor Flow Meter. foreign material fall inside of the Vapor Flow Meter. 5. Next,prepare the piping inside of the dispenser sump to connect to the Vapor 5. Next,start assembling the hardware from the bottom up.Connect Flow Meter.If flexible piping is currently installed,make sure,when adding a short,1"NPT threaded nipple to the top of the vapor shear the Vapor Flow Meter,that there are no bend radii that are too sharp,kinks, valve and to the 1.5"to V reducing bushing on the flow meter. or traps.The contractor may need to replace the existing flexible piping with a 6. Connect another 1"pipe nipple to the lop reducing bushing shorter length in order to avoid potential flow restrictions. followed by a 1"pipe union.The existing dispenser piping can 6. Add the Vapor Flow Meter between the existing piping in the sump and the now conned to the top of the union. bottom of the vapor shear valve.In most cases the vapor shear valve will need 7. If there is not already a watertight junction box for the intrinsically to be temporary removed in order to assist with making the connection.Add a safe cables,then install one as described earlier in Tools union to either the top of the shear valve or below the shear valve. Required. 7. If there is not already a watertight junction box for the intrinsic safe cables,then 8. Pull the black Vapor Flow Meter cable through the supplied install one as described earlier in Tools Required. cable grip and into the junction box.Using the supplied 8. Pull the black Vapor Flow Meter cable through the supplied cable grip and into crimp connectors,splice the flow meter cable to the field the junction box.Using the supplied crimp connectors,splice the flow meter cable.The color codes on the black flow meter cable are: cable to the field cable.The color codes on the black flow meter cable are: Red=+(plus)and Black=-(minus) Red=+(plus)and Black=-(minus) Page 1 of 2