Laserfiche WebLink
UL/ULC Listed Red Three II A Piping System <br /> RED THREAD IIA PIPING <br /> RED THREAD IIA Primary Piping RED THREAD IIA Secondary Containment Piping <br /> Nom. Pipe PipeNom.Pipe Pipe <br /> .`i Size Part Length Sb:e Part Length <br /> -t -kil Number (ft.) (InJmm) Number (ft.) <br /> 50 011020-069-1 15 3 80 011030-069-4 15 <br /> 2 50 011020-069-2 22-25 3 80 011030-069-5 22-25 <br /> 50 011020-069-3 26.30 3 80 011030-069.6 26-30 <br /> 3 80 011030-069-1 15 4 100 011040-077-5 15 <br /> 80 011030-069-2 22-25 4 100 011040-069-5 22-25 <br /> 3 80 011030-069-3 26-30 4 100 011040-077-6 26-30 <br /> 4 100 011040-071-1 15 6 150 011060-120-5 15 <br /> 4 100 011040-069-2 22-25 6 150 011060-120-4 22-25 <br /> 4 100 011040-071-3 1 26-30 6 150 1 011060-120-6 1 26-30 <br /> DIMENSIONAL DATA <br /> Nominal Nominal Mill <br /> PI a Nominal Nominal Wall Nominal Pressure/ Test External Pressure <br /> S e I.D. O.D. Thickness Weight Temperature Pressure Max.Rating(psIglMPa) <br /> (in m) (inJmm) (in./mm) (InJmm) (IbsAL/kgan) Max.Rating (psIglMPa) 75°F/24°C 1509F/66"C <br /> 2 2.235 2.375 .070 0.5 - 250 psig @ 1 50'0 375 85 80 <br /> 50 57 61 1.78 0.74 1.72 MPa @ 66'C 2.59 .57 .55 <br /> 3 3.360 3.500 .070 0.7 175 psig @ 150'F 300 36 34 <br /> Bp 85 90 2.54 1.04 1.21 MPa @ 66'C 2.07 .25 .23 <br /> °4 4.360 4.560 .085 1.2 125 psig @ 150'F 265 34 30 <br /> 100 111 116 2.16 1.79 0.86 MPa @ 66'C 1.83 .23 .21 <br /> 6 6.408 6.678 .135 2.4 NA 265 22 20 <br /> 150 163 170 3.43 3.51 NA 1.83 .15 .14 <br /> I <br /> N TYP CAL PHYSICAL PROPERTIEW) <br /> PROPERTY RED THREAD'IIA Pipe r' Bending Radius,Minimum <br /> psi @ 75•F MPa @ 24"C psi @ 150'F MPa @ 66'C Nominal <br /> Pipe Size 2° 3" 4" 6" <br /> Axialensile(ASTM D2105) Inches <br /> UI mate Stress 10,300 71.0 8,200 56.5 <br /> Design Stress 2,575 17.8 2,050 14.1 Ft. 75 110 140 204 <br /> Modulus of Elasticity 1.82 x 10° 12548 1.42 x 117 9791 <br /> Axial Compression(ASTM D695) 33,300 230.0 25,600 177.0 In 21.3 33.5 42.7 62.2 <br /> Ultimate Stress 8,300 57.2 6,400 44.1 <br /> Design Stress 1.26 x 10' 8687 .89 x 101 6136 <br /> Modulus of Elasticity <br /> I (i)*All values except pressure-temperature <br /> i Beam Bending(SFPTM) maximum rating are nominal values.Tolerances or <br /> Ultimate Stress 23,000 159.0 19,200 132.0 maximumlminimum limits can be obtained from Smith <br /> Design Stress') 2,900 20.0 2,400 16.5 Fibercast. <br /> Modulus of Elasticity 2.18 x 10° 15031 1.70 x 101 11721 (2) All sizes can accept full vacuum pressures at <br /> (Long Term per ASTM D2925) maximum temperature ratings. <br /> (3) Ultimate and allowable design stresses are <br /> Hydrostatic Burst(ASTM D1599) based on minimum reinforced wall thickness.Pipe is <br /> Ultimate Hoop 34,000 234 39,200 271 manufactured in compliance with ASTM D2996. <br /> 'y Tensile Stress (4) Design bending stress is 118 of ultimate to <br /> 1 <br /> Hydrostatic Design ASTM D2992 2"-3' 2"&3" 2"&3" 2"&3" account far combined stress(i.e.bending and <br /> yd g ( ) pressure). <br /> Procedure A 9,410°i 64.90' 7,400m -6 (5) Design stress is based on long term cyclic fatigue <br /> Cyclic 150 x 10' 4"-6 4"-6" 4"-6" 4°" 6' data using ASTM D2992 test method.However,all <br /> Cycles 13,040'°' 89.9101 10,450 72.1 testing is not complete at time of printing. <br /> (6) For RED THREAD IIA pipe the hydrostatic <br /> ' <br /> Coefficient of Linear 0.88 x 104 in.lin./'F cyclic design stress was determined at 150'and <br /> H Thermal Expansion(SFPTM) 1.58 x 10'Omm/mml'C 2007,per ASTM D2992 Procedure A.Based on this <br /> data,the extrapolated value at 75'F Is 13,030 psi. <br /> S ' cifc Gravity 1.8 (7) For RED THREAD IIA pipe the hydrostatic cyclic <br /> N FI w Factor design stress was determined at 75'and 200'F,per <br /> f Hazen-Williams Coefficient 150 ASTM D2992 Procedure A.Based on this data,the <br /> ka9 extrapolated value at 150'F Is 7,400 psi. <br /> 4 <br />