COMPLIANCE INFO 2008 - 2015 - Laserfiche WebLink

Home Browse Search

UL/ULC Listed Red ThrTo II A Piping System RED THREAD IIA PIPING RED THREAD IIA Primary Piping RED THREAD IIA Secondary Containment Piping Nom.Pipe Pipe P Nom,Pipe Pipe 1 Size Part Length Size p Imm) Number g, Part Length � . ( ) (In./mm) Number 50 011020-069-1 15 3 80 011030-069-4 15 2 50 011020.069-2 22-25 3 80 011030-069-5 22-25 I 50 011020-069-3 26-30 3 80 011030-069-6 26-30 3 80 011030-069-1 15 4 100 011040-077-5 15 ( 80 011030-069-2 22-25 4 100 011040-069-5 22-25 3 80 011030-069-3 26-30 i 4 100 011040-077-6 26-30 4 100 011040-071-1 15 6 150 011060-120-5 15 4 100 011040-069-2 22-25 6 150 011060-120-4 22-25 4 100 011040-071-3 2630 6 150 011060-120-6 26-30 DIMENSIONAL DATA No ninal Nominal Mill pe Nominal Nominal Wall Nominal Pressure/ Test Sze I.D. O,D. Thickness Weight Temperature ' Pressurexternal Pressure (in mm) (InJmm) (InJmm) (InJmm) (IbsJBJkgirl) Max.RatingMax.MRating(psi 50OF16 (psig/MPa) 75°F124°C 750°FI66°C 2.235 2,375 .070 0.5 - 250 psig @ 150'F 375 85 80 57 61 1.78 0.74 1.72 MPa @ 66°C 2.59 .57 3.360 3.500 .55 0 .070 .7 175 psig @ 150°F 300 36 34 85 90 2.54 1.04 1.21 MPa @ 66°C 2.07 .25 4.360 4.560 .085 1.2 125 si 23 P 9 @ 150°F 265 34 30 1 0 111 116 2.16 1.79 0.86 MPa @ 66°C 1.83 6.408 6.678 .135 2,4 NA .23 .21 265 22 20 1 163 170 3.43 3.51 NA 1.83 15 .14 TYPICAL PHYSICAL PROPERTIES(') PROPERTY RED THREAD°IIA PI a �' Bending Radius,Minimum psi @ 75°F MPa @ 24°C psi @ 150°F MPa @ 66°C pipe Size 2" 3' q' 6" ominal Axial T nsile(ASTM D2105 Inches Ulbmate Stress 10,300 71.0 8,200 56.5 Design Stress 2,575 17.8 2,050 14.1 Ft. 75 110 140 204 Modulus of Elasticity 1.82 x 101 12548 1.42 x 1g' 9791 Axial Compression(ASTM D695) 33,300 230.0 25,600 m 21.3 33.5 42.7 62.2 Ultimate Stress 8,300 57.2 6,400 44.1 171.0 Design Stress Modulus of Elasticity 1.26 x 10° 8687 .89 x 10° 6136 Beam Bending(SFPTM) (1)-Allvalues except pressure-temperature Ulb' 'ate Stress 23,000 159.0 19,200 132. Nm0 maximum rating are nominal values.Tolerances or Des' n Strei 2,900 20.0 2,400 16.5 meximurinimum limits can be obtained from Smith Mod Jus of Elasticity 2.18 x 10° 15031 1.70 x 101 11721 FJberrast. (Lor I Term per ASTM D2925) (2) All sizes can accept full vacuum pressures at maximum temperature ratings. Hydrost tic Burst(ASTM D1599) (3) Ultimate and allowable design stresses are Ultin ate Hoop based on minimum reinforced wall thickness.Pipe is Tensile Stress 34,000 234 a7,400m5lo) manufactured In compliance with ASTM 02996, ' (4) Design bending stress is 1IS of ultimate to Hydrostatic Design(ASTM D2992) 2'-3' 2'8 3" 3' account for combined stress(i.e.bending and Procedure 9,410' 64.901 pressure). Cyclic 150 x 10° 4'-6" 4"-6° " (5) Design stress Is based on long term cyclic fatigue Cycles 13,040'°' 89.9"1 data using ASTM D2992 test method.However,all testing is not complete at Uma of printing. Cceffid t of Linear 0.88 x 10 . . (6) For RED THREAD IIA pipe the hydrostatic The al Expansion(SFPTM) 1.58 x 104mm/mm/°C cyclic design stress was determined at 150°and 201 per ASTM D2992 Procedure A.Based on this Spec c Gravity 1.8 data,the extrapolated value at 75°F is 13,030 psi. Flow actor (7) For RED THREAD IIA pipe the hydrostatic cyclic Hen-Williams Coefficient 150 design stress was determined at 75°and 201 per ASTM D2992 Procedure A.Based on this data,the extrapolated value at 150°F is 7,400 psi. 4