Laserfiche WebLink
ULJULC Listed Red Th 0& II A Piping System • <br /> RED THREAD IIA PIPING <br /> RED THREAD IIA Primary Piping RED THREAD IIA Secondary Containment Piping <br /> > Nom.Pipe Pipe Nom.Pipe Pipe <br /> :^; � �� j Size Part Length size Part Length <br /> _kbImm) Number (ft.) (In.lmm) Number (ft.) <br /> 50 011020-069-1 15 3 80 011030-069-4 15 <br /> 2 50 011020-069-2 22-25 3 80 011030-069-5 22-25 <br /> 50 011020-069-3 26-30 3 80 011030-069-6 26-30 <br /> 3 80 011030-069-1 15 4 100 011040-077-5 15 <br /> 80 011030-069-2 22-25 4 100 011040-069-5 22-25 <br /> i 3 80 011030-069-3 26-30 4 100 011040-077-6 26-30 <br /> 4 100 011040-071-1 15 6 150 011060-120-5 15 <br /> 4 100 011040-069-2 22-25 6 150 011060-120-4 22-25 <br /> i 4 100 011040-071-3 1 26-30 6 150 1 011060-120-6 26-30 <br /> j DIMENSIONAL DATA <br /> Nominal Nominal Mill <br /> Pipe Nominal Nominal Wall Nominal Pressure/ Test External Pressure <br /> Size I.D. O.D. Thickness Weight Temperature ' Pressure Max.Rating(psIg/MPa) <br /> (inJmm) (InJmm) (InJmm) (InJmm) (IbsJftAg{n) Max.Rating (psiglMPa) 75°F124°C 150'F/66°C <br /> 2 2.235 2.375 .070 0.5 - 250 psig @ 150-F 375 85 80 <br /> i 0 57 61 1.78 0.74 1.72 MPa @ 66°C 2.59 .57 .55 <br /> ' 3 3.360 3.500 .070 0.7 175 psig @ 150°F 300 36 34 <br /> 0 85 90 2.54 1.04 1.21 MPa @ 66°C 2.07 .25 .23 <br /> 4 4.360 4.560 .085 1.2 125 psig @ 150°F 265 34 30 <br /> 00 111 116 2.16 1.79 0.86 MPa @ 66°C 1.83 .23 .21 <br /> 6 6.408 6.678 .135 2.4 NA 265 22 20 - <br /> 50 163 170 3.43 3.51 NA 1.83 .15 .14 <br /> TY 'ICAL PHYSICAL PROPERTIES(" <br /> PROPERTY RED THREAD'IIA PI a r' Bending Radius,Minimum <br /> psi @ 75°F MPa @ 24°C psi @ 150°F MPa @ 66°C Nominal <br /> Pipe Size 2" 3° 4" 6- <br /> Axial Tensile <br /> "AxialTensile(ASTM D2105) Inches <br /> Ultimate Stress 10,300 71.0 8,200 56.5 <br /> Design Stress 2,575 17.8 2,050 14.1 Ft. 75 110 140 204 <br /> Modulus of Elasticity 1.82 x 10' 12548 1.42 x 10' 9791 <br /> AxialCompression(ASTM D695) 33,300 230.0 25,600 177.0 m 21.3 33.5 42.7 62.2 <br /> Ultimate Stress 8,300 57.2 6,400 44.1 <br /> sign Stress 1.26 x 101 8687 .89 x 101 6136 <br /> ulus of Elasticity <br /> (1)-All values except pressure-temperature <br /> Bea Bending(SFPTM) maximum rating are nominal values.Tolerances or <br /> timate Stress 23,000 159.0 19,200 132.0 maximum/minimum limits can be obtained from Smith <br /> sgn SVess"' 2,900 20.0 2,400 16.5 Fiberoast. <br /> odulus of Elasticity 2.18 x 10° 15031 1.70 x 101 11721 (2) All sizes can accept full vacuum pressures at <br /> (4ong Tenn per ASTM D2925) maximum temperature ratings. <br /> Hydrostatic Burst ASTM D1599 (3) Ultimata and allowable design stresses are <br /> Y ( ) based on minimum reinforced wall thickness.Pipe is <br /> Ultimate Hoop 34,000 234 39,200 271 manufactured in compliance with ASTM D2996. <br /> Tonsils Stress (4) Design bending stress is 1/8 of ultimate to <br /> H drdstatic Design ASTM D2992 2'-3" 2"&3" 2'&3' 213' account far combined stress(i.e.bending and <br /> Y 9 ( ) pressure). <br /> Piocedure A 9,410"' 64.911' 7,400^ 51P1 (5) Design stress Is based on long fano cyclic fatigue <br /> Cyclic 150 x 10° 4'-6- 4"-6" 4'.6- 4'-6- data using ASTM D2992 test method.However,all <br /> Cycles 13,0409°' 89.90' 10,450 72.1 tasting is not complete at time of printing. <br /> Cceft�Gent of Linear 0.88 x 10s in.fln./°F (6) For RED THREAD IIA pipe the hydrostatic <br /> Thermal Expansion SFPTM 1.58 x 10*mm/mml°C cyclic design stress was determined at 150°and <br /> p ( ) 200°F,per ASTM 02992 Procedure A.Based on this <br /> data,the extrapolated value at 75°F is 13,030 psi. <br /> Specific Gravity 1.8 (7) For RED THREAD IIA pipe the hydrostatic cyclic `r <br /> Flow Factor design stress was determined at 75°and 200°F,per <br /> Hazen-Williams Coefficient 150 ASTM D2992 Procedure A.Based on this data,the <br /> extrapolated value at 150°F Is 7,400 psi. <br /> 4 <br />