INSTALL_2012 - Laserfiche WebLink

Home Browse Search

5. If your sumps had vacuum,proceed with the installation per the products respective Installation Manual.Yew them HERE. 6. If your sumps did not hold vacuum,call Bravo systems with the results of your testing so we can better help you. If you are shipped replacement gauges:After you install them per the provided instructions, follow the overnight vacuum test outlined in#4 above to conduct a factory test of a re-sealed interstice. 09:What common types of repairs are allowed on Bravo shallow pans? Read installation instructions on Bravo B2000 Shallow pans to see if they clarify how to repair various problems. • For B-18-3'Black Plastic Compression fittings leaking between gasket and pipe. Use WR-3 wrench to loosen seal between nut and doughnut gasket.Apply wet-dry grease between nut and gasket to allow nut to easily make a compression seal. If you can not get grease between nut and gasket spray WD-40 between surfaces to lubricate hard to reach areas. Then compress nut to%to%turns past hand tight. • For Electrical fittings that do not have a seal or are leaking. If possible retrofit a compression fitting that seals to both the conduit and Bravo fitting. Blue Line has a split electrical fitting for this application. If split fittings do not apply, then use adhesive to seal annular space by first cleaning and prepping the area around conduit and fitting to remove all contaminates that will prevent bonding of adhesives. Pack annular space and seal area with one of three recommended adhesives: Bravo Vulkem sealant(VS), PetroSeal or Bravo 8400-Adhesive Kit. • For Shallow Pans with Divider Tabs-Required to electronically monitor each section?You have an option. You are authorized to remove the liquid divider(s)or a portion of them. You need only to remove an area of a few inches from each divider to facilitate unrestricted liquid communication between the previously isolated containment zones. 1. Remove all mechanical float trip mechanisms and their assemblies. 2. Remove any sealant at the divider area you wish to remove. 3. Using Tin-Snips,ship the divider vertically in two places and remove the loose piece. 4. Seal arty metal that was cut,scratched or dinged with Vutkem sealant or PetroSeal to prevent against corrosion. 5. Use water to determine which Float cup qualifies as the lowest point. 6. Remove all liquids from the sump.Clean and dry the sump interior. 7. Install the sensor to that cup(lowest point)and mark sump so future maintenance technicians will rot move the sensor to another Float cup. GUIDELINES: No exposed Steel. No power tools on the dividers. Electronic Sensor must be placed at the lowest point. • How can I clean up the bottom of a Steel Dispenser Containment unit?Follow this procedure: A) Use any solvent or cleaning solution you prefer. B)Scrape the bottom and/or walls with a flat-blade tool. C)Vacuum out any liquids, gunk, etc.. D)Acetone to clean the surfaces so a visual inspection can be made. E) Lightly sand all areas where the factory epoxy-paint is missing. F) Dust, blow out and/or vacuum any debris from the interior. G) Protect any exposed test ports or threads, remove any electronic sensors. H)Coat the interior well with AmerShield, covering all exposed steel. For Product Information on AmerShield, Click Here. For Information on Surface Preparation, Click Here. Note:Always check with you local regulatory authority for additional guidelines and permitting. 010:Can I modify or repair a Bravo Conversion Frame? A:No. Under no circumstances can you modify, repair or add to a Bravo Systems Dispenser Conversion Frame (CONV-B2000)unless authorized in writing by the factory. When authorized, typical allowances include opening a We in the drainage louver panels only to allow conduit to pass through from below. In this specific case,the hole cut must conform to the O.D.of the conduit as closely as possible. Proper surface preparation and cleaning is necessary,followed by a heavy application of Vulkem 116 sealant. If this process is conducted on a site without proof of written authorization from Bravo,that installation is non-compliant and should be replaced or addressed per all local codes,reguations or applicable laws. http://www.sbmvo.com/faq.htrn