COMPLIANCE INFO 2001-2004 - Laserfiche WebLink

Home Browse Search

e`i16i26@1 G: 14 80088 00 SHIE_DS,HARP Co. PAGE 65 sed decals to the diapenaerdialgiaaeaa,'.. a. Remove 1/4-inch pipe plug from tank test port in grade,o8 gaaolina upo¢:whir3t-the leak detector-is.�j the Packer (on 6-inch Big-Flo applications, ra- ., ;. beiaglimatallid:.Addrdonai:decals-are available; mak';:- nurse the 114-inchpipe plug$omthe riser/flange - cveCo:a�aervioeatl=tlOff=9fi2:8348ar(913)49&-6708' .- assemhly). ;s 10: Irlspectallthreaded joints toassuretheyaretightand' b. Apply a ALtimaified non-toxic pipe thread seal- not leaking: _ ant to the V4-inch NPT 45-degree elbow and install in tank test port of the packer. On 5-inch Test of the Leak Detector Big-Flo applications,the 1/4-inch NPI'45-degree elbow may be installed into the riser/flange U.S. Environmental Protection Agency(EPA)regulations re- assembly. quire annual verification of operation of leak detector. To C. Install a 1/4-inch NPT tee on the 4"egtee elbow ass13re maintenance of leak detection capability, Red Jacket that is in the teak teat part(or on&inch Big-Flo requires.that.operation of the mechanicaL.lealt,dareear..be. rimer/flange assembly)to accommodate both the verified by.testing upon itart-up sad.tliattestine of:the beak vent tube and snap tap. dete[mr.be peifurmed routinely at leant annually.._...... .._:-_ d. Apply a.UL-classified man-toxic pipe thread seal- ant to the threads of the 1/4-inch NPT 90-degree 11119�[ Tess procedure options for mechanical elbow vent tube fitting and install in the.tee, leak detectors are explained in Red Jacket e. Apply a UL-classified non-toxic pipe thread seal- Engineering Reports,RJ20 and RJ21.The ant to the threads of the 1/4-inch NPr straight Red Jacket Snap Tap tormentors allow vent tube fitting and install is the leak detector the F:Y2V/F=Vleak detoetorto be tested tion vent opening in the cap of the leak detector. with the A Snap Tap Taster as as op. .to thee above test methods- See Rad L Install the vent tubing into both fittings and Jacket literature #042-111-1 for teat in- tig ceu. structions using Snap Tap Connevton. g. To install snap tap connectors in FX2V/MDV models, apply a LTL-classified non-toxic pipe 11. The tap cover an the Red Jacket leak detector is thread sealant to the snap tap connectors and designed to accommodate a sealing wire which can be install one in the body of the FXV leak detector used to di3courage tampering or the unauthorized andthe otherin the tee attached to the 45-degree removal of the leak detector(see Figure 2). elbow installed in the tank test port of the packer. On 6-inch Big-Flo applications, install the two a It should be noted that if the dispensing snap tap connectors — one in the FXV leak system(the solenoid valve and the nozzle) detector and one in the riser/flange assembly. Is opened previous to the completion of the line test, the FXV Series will detect h. Attach and crimp loop of the retaining tether this opening me a leak and restricted flow around the Snap Tap threads. will result. Closing of the nozzles)for a i. Replace the raps over the quick-correct cou- period of time adequate to allow comple- plingn and tighten snugly. tion of the line test will allow the leak DO NO overtighten, detector to open.Once opened,full pump flow can be provided. See technical bulletin #042411.1 for use - of Snap Tap Connector Assembly. 7. Connect power to pump at the load center. PX2V/FX21)v_ -� S. Clear remaining air from system as follows: TETHERED a. Turn on dispenser that is farthest from the leak CAP detector but do not open nozzle.Wait four or five minutes or more. Look for leaks on parts worked on. SNAP TAP b. Shut off the pump and allowitto standfourorfive AS' ELBOW minutes. Than start the pump again and ^ open the nozzle farthest from the leak detector. I/�� C. Continue to dispense enough gasoline, about 20 to 30 gallons(76 to 114 liters), to pump ALL air Figure TI from the system. REMMIf flow is restricted to about 3 gpm (11 Ipm) or less with the nozzle open,the leak detector has not opened.Repeat stop Be with increased running time of pump SEALING WIRE to Insure the purging of all air. All air (provided by contractor) meet be purged from the system or the O leak detector will restrict flow to about 3 gpm (11 Ipm). ® Marley Pump I IV 114-INCH A uneea demwm tenoee T-FITTING I 7401 W. 129 St.• Overland Park, KS 56213 •913-498-5700 •-off Marley Pump reserves the right to make design improvements and pricing mooltirslions as necessary and without notice. VENT TUBE 01994 Marley PUMP Printed In USA Figure 2