COMPLIANCE INFO 2006 - 2012 - Laserfiche WebLink

Home Browse Search

r Typical mechanical properties of primary pipe Method Pipe Property' Units Value' ASTM ATM2 Tensile strength GPa 20.7 Longitudinal 103 psi 35.0 D2105 161 f 2 50 75 23 15 13 4 MPa 241 Circumferential 103 psi 70.0 D1599 151 Longitudinal MPa 483 Tensile modulus Longitudinal 106 psi 3.0 D2105 161 Nominal Bending Deflection Length Required GPa 20.7 Circumferential 106 psi 4.2 — — 2 50 75 23 15 13 4 GPa 29.0 Compressive strength 4 100 150 46 7.5 27 8 Longitudinal 103 psi 35.0 — 142 Important notice MPa 241 Compressive modulus lation, changes in operating procedures, or extrapolation of data may cause different results. Longitudinal 106 psi 3.0 — 142 merchantability or fitness for purpose, as to the accuracy, adequacy or completeness of the recom- GPa 20.7 Long-term hydrostatic with this literature or the information or recommendations it contains. AMERON design basis INTERNATIONAL P.O. Box 801148 • Houston, TX 77280 • Tel: (713) 690-7777 • Fax (713) 690-2842 • http://www.ameron.com Static 103 psi 31.5 D2992(13) — Fiberglass Pipe Division Fiberglass Pipe Division Ameron Composites Fiberglass Pipe Division MPa 217 Cyclic 103 psi 8.0 D2992(A) — J.F. Kennedylaan 7 Burkbumett, TX 76354 Newnan, Georgia 30263 600 FM 1195 South MPa 55 Poisson's ratio3 vyx _ 0.16 — — v,Y 0.26 — — 1) Based on structural wall thickness. 2) Ameron test method. 3) The first subscript denotes the direction of contraction and the second that of the applied stress. x denotes longitudinal direction. y denotes circumferential direction. Bending radius Minimum Maximum Minimum Nominal Bending Deflection Length Required Pipe Size Radius' per 20 -ft Joint for 10° Change (in) (mm) _ (ft) (m) (deg) (ft) (m) 2 50 75 23 15 13 4 3 80 125 38 9 22 7 4 100 150 46 7.5 27 8 1) At rated pressure. Sharper bends may create excessive stress concentrations. Do not bend pipe until adhesive has cured. Important notice This literature and the information and recommendations it contains are based on data reasonably believed to be reliable. However, such factors as variations in environment, application or instal- lation, changes in operating procedures, or extrapolation of data may cause different results. Ameron makes no representation or warranty, expressed or implied, including warranties of merchantability or fitness for purpose, as to the accuracy, adequacy or completeness of the recom- mendations or information contained herein. Ameron assumes no liability whatsoever in connection - 1% with this literature or the information or recommendations it contains. AMERON GRouP HEADQuARTERs INTERNATIONAL P.O. Box 801148 • Houston, TX 77280 • Tel: (713) 690-7777 • Fax (713) 690-2842 • http://www.ameron.com FIBERGLASS PIPE GROUP Fiberglass Pipe Division Fiberglass Pipe Division Fiberglass Pipe Division Ameron Composites Fiberglass Pipe Division Asia Europe Americas P.O. Box 71370 Centron International Ameron (Pte) Ltd. Ameron B.V. P.O. Box 878 11 McBride Street P.O. Box 490 No. 7A, Tuas Avenue 3 J.F. Kennedylaan 7 Burkbumett, TX 76354 Newnan, Georgia 30263 600 FM 1195 South Singapore 639407 4191 MZ Geldermalsen TeL (940) 569-1471 Tel: (770) 253-2000 Mineral Wells, Texas 76068 Tel: 65 8616118 The Netherlands Fax: (940) 569-2764 Fax: (770) 253-9234 Tel: (940) 325-1341 Fax: 65 8621302/8617834 Tel: +31345 587 587 Fax: (940) 325-9681 Fax: +31345 587 561 Telex: 40257 bonds nl 01997 Ameron FP737C (12/98) supercedes FP7378 (9/98) Printed in U.SA 5M