Laserfiche WebLink
SERVICE PRO• <br />CONTROL CENTER <br />°-llVfJ11-°' NOTE <br />TIME CLOCK <br />ALARM IS FACTORY <br />LIGHT PRESET TO <br />RUN 30 MIN <br />TP) II 11 PER HOUR <br />W W W.S ERV ICE PROMCD.COM <br />SWITCH 71­__� ON <br />NORWECO, INM- <br />NORWALK, OHIO <br />U.S.A. <br />OFF <br />SERVICE PRO® CONTROL CENTER <br />Prewired controls are supplied in a sealed NEMA rated <br />enclosure for your safety and the protection of components <br />and wiring. The controls should be located so the alarm <br />light can be seen and the audible alarm heard, while <br />minimizing exposure to harsh weather or conditions that <br />might prevent routine access. If an issue with the aerator is <br />detected, the red alarm light will flash and the control center <br />will attempt to restart the aerator every five minutes for <br />two hours. For an open motor or under current condition, <br />the alarm light will display two short flashes followed by a <br />pause. For an over current condition, the alarm light will <br />flash evenly. If the aerator does not restart after two hours, <br />the audible alarm will sound. To silence the audible alarm <br />and attempt to restart the aerator, push the reset button. If <br />the alarm condition is not resolved, the audible alarm will <br />be silenced for 48 hours, but the alarm light will continue <br />to flash. In this case, contact your service provider. Model <br />960 systems are supplied with a time clock adjustable in <br />five minute increments up to continuous run. This clock is <br />factory preset to run 30 minutes per hour and should only be <br />adjusted by an authorized Singulair service provider. Model <br />TNT systems are supplied with a non-adjustable time clock. <br />SERVICE PRO® MONITORING CENTER <br />An optional Service Pro MCD control center is available <br />for use with the Singulair system. Designed to connect <br />to a standard telephone line or internet connection, this <br />control center provides MONITORING, COMPLIANCE <br />and DIAGNOSTIC functions complete with telemetry for <br />communication with the Service Pro monitoring center. <br />Once your Service Pro MCD control center is connected to <br />a telephone line or internet connection, commissioned, and <br />covered by a remote monitoring agreement, your service <br />provider will be immediately notified of any alarm condition. <br />The Service Pro monitoring center will automatically log <br />the time and date of alarm conditions, as well as service <br />performed, and store them in your system history record <br />for viewing at www.servicepromcd.com. <br />NOTE: The control center regularly communicates with the <br />Service Pro monitoring center using your telephone line or <br />an internet connection. If the control center is using the <br />telephone line when you attempt to place a call, a high <br />pitched digital communication signal will be heard. Hang <br />up all telephones sharing the line and wait a few seconds. <br />This will automatically disconnect the control center and <br />make the line available for use. <br />BIO -STATIC® SLUDGE RETURN <br />Each Bio -Static sludge return is installed in the aeration/ <br />clarification chamber wall. Aeration chamber hydraulic <br />currents enter the sludge return(s) and transfer solids from <br />the clarification chamber back to the aeration chamber <br />for additional treatment. The Bio -Static sludge return <br />accomplishes resuspension and return of settled solids <br />without disturbing the contents of the clarification chamber. <br />BIO -KINETIC® SYSTEM <br />Bio -Kinetic systems provide non-mechanical flow <br />equalization through all plant processes. The Bio -Kinetic <br />system contains 3 separate filtration zones, 8 independent <br />settling zones, optional chlorination and dechlorination <br />tablet feed systems and serves as its own chlorine contact <br />chamber. When used with Blue Crystal disinfecting tablets, <br />the performance of the Bio -Kinetic system as a disinfection <br />device is certified to NSF/ANSI Standard 46, Section 11. <br />All components are manufactured from plastic or rubber. <br />Your service provider has the necessary training, tools and <br />equipment for removal and cleaning. If your Bio -Kinetic <br />system is in need of service, contact your service provider. <br />During each semi-annual service inspection, your service <br />provider will remove and clean the Bio -Kinetic system or <br />replace it with a unit from their service stock. <br />BIO -KINETIC SYSTEM OPTIONAL BLUE CRYSTAL <br />MOUNTING CASTING COVER CHLORINATION SYSTEM <br />GIRADE D \..\..�\..\. QI / I F' ..�\..�\..�\..�� FINISHEDGRADE <br />DESIGN FLOW LINE <br />BIO -STATIC /_ II I \ OUTLET COUPLINCE <br />G <br />SLUDGE RETURN <br />COMPARTMENTED-_ FILTER MEDIA <br />SETTLING ZONE RETAINER <br />VE <br />