|
GENERAL: >_
<br /> 1 . ALL WORK PERFORMED SHALL BE IN ACCORDANCE WITH ALL LOCAL CODES 20. ALL ROOFTOP CONDENSING UNITS THAT DISCHARGE HORIZONTALLY SHALL BE
<br /> AND ACCEPTABLE TO THE AUTHORITY HAVING JURISDICTION. ORIENTED SUCH THAT THE DISCHARGE DOES NOT BLOW IN THE DIRECTION OF AIR DEVICE SCHEDULE D RAW I N G NOTES
<br /> 2. ALL DIMENSIONS, CLEARANCES AND TOLERANCES SHALL BE VERIFIED PRIOR AN OUTDOOR AIR INTAKE.MK ABBREVIATIONS TAG MANUFACTURER MODEL BORDER SIZE COLOR ACCESSORIES NOTES
<br /> TO INSTALLATION. COMMERCIAL KITCHEN EXHAUST SYSTEMS: 1 . ALL NEW AND EXISTING DUCTWORK SHALL BE RUN BETWEEN OR
<br /> 1. ALL METAL DUCTWORK USED FOR THE CONVEYANCE OF GREASE-LADEN AIR ACM AREA CONSTRUCTION MANAGER S-2 TITUS OMNI LAY-IN 24x24 VARIES 4,6,7 THROUGH THE JOISTS UNLESS NOTED OTHERWISE. CONNECT TO
<br /> 3. ALL MATERIALS, FIXTURES AND EQUIPMENT USED SHALL BE IN ACCORDANCE SHALL BE CONSTRUCTED OF MINIMUM 18 GAUGE STAINLESS STEEL OR 16 PRICE SPD NEW OR RELOCATED DIFFUSERS AS REQUIRED. DUCTWORK
<br /> WITH McDONALD'S SPECIFICATIONS. SPECIFICATIONS ARE CONTAINED WITHIN GAUGE CARBON STEEL (BLACK IRON). S-3 TITUS OMNI LAY-IN 12x12 VARIES 1,2,7 1,3,7 DESIGNATED WITH (B.J.) SHALL BE RUN BELOW THE JOISTS.
<br /> THESE DRAWINGS AND THE McDONALD'S PROJECT MANUAL. ANY CONTRACTOR BSI BEVERAGE SYSTEM INSTALLER PRICE SPD
<br /> IN NEED OF A COPY OF THE McDONALD'S PROJECT MANUAL SHALL CONTACT 2. ALL GREASE EXHAUST DUCTWORK JOINTS SHALL BE EITHER TELESCOPING OR TITUS 23RL 2. DUCT SIZES SHOWN ARE INTERNAL FREE AREA DIMENSIONS
<br /> THE McDONALD'S AREA CONSTRUCTION MANAGER. ANY VARIANCE FROM THE BELL TYPE. BUTT-WELDED JOINTS ARE PROHIBITED. R-1 PRICE 60L LAY-IN 24x24 VARIES 3,7 UNLESS NOTED OTHERWISE.
<br /> McDONALD'S SPECIFICATIONS SHALL BE REVIEWED AND APPROVED BY THE 3. ALL GREASE EXHAUST DUCTWORK SEAMS AND JOINTS SHALL BE EC ELECTRICAL CONTRACTOR TITUS 23RL 3. DIFFUSERS IN DINING ROOM ARE SPECIFIC TO THE DECOR PLAN
<br /> ENGINEER-OF-RECORD. CONTINUOUSLY WELDED WATER-TIGHT ON THE EXTERNAL SURFACE OF THE E-1 PRICE 60L LAY-IN 12x12 WHITE 1,7 SHOWN. DIFFERENT CEILING LAYOUTS MAY REQUIRE A DIFFERENT z
<br /> 0
<br /> DUCT SYSTEM. ALL WELDING SHALL BE PERFORMED BY A CERTIFIED WELDER. DIFFUSER TYPES, QUANTITIES, LOCATIONS AND FINISHES/COLORS.
<br /> 4. ALL EQUIPMENT SHALL BE INSTALLED IN ACCORDANCE WITH ITS LISTING FAC FIRE ALARM CONTRACTOR ACCESSORIES: NOTES: a_
<br /> AND/OR THE MANUFACTURER'S INSTALLATION INSTRUCTIONS. 1 . COMBINATION DAMPER AND 1. SEE PLAN FOR NECK SIZES
<br /> 4. ALL GREASE EXHAUST DUCTWORK SHALL BE EXTERNALLY INSULATED WITH A
<br /> EQUALIZING GRID 2. FABRICATE 46%22%27"H PLENUM WITH 14"0 SIDE INLET co
<br /> 5. SEE COORDINATION SCHEDULE FOR ADDITIONAL SCOPE OF WORK. ASTM E2336 LISTED AND LABELED GREASE DUCT ENCLOSURE SYSTEM. 2. PLASTER FRAME FOR DRYWALL (SEE DETAIL 10 ON DRAWING M3.0) o
<br /> INSULATION SHALL BE INSTALLED IN ACCORDANCE WITH ITS LISTING AND THE FPC FIRE PROTECTION CONTRACTOR CEILING INSTALLATION
<br /> MANUFACTURER'S INSTALLATION INSTRUCTIONS. 3. SQUARE-TO-ROUND COLLAR 3. PROVIDE 1 " FIBERGLASS INSULATION FOR DIFFUSER KEYED NOTES
<br /> 6. PRIOR TO BUILDING TURNOVER, A COMPLETE START-UP, TEST, ADJUST AND CONNECTION BACKPAINBALANCE SHALL BE PERFORMED ON ALL MECHANICAL SYSTEMS. THIS WORK 4. NOT USED
<br /> 5. ACCESS PANELS SHALL BE PROVIDED AT ALL CHANGES IN DIRECTION OF THE GC GENERAL CONTRACTOR 4. BACKPAN INSULATION
<br /> SHALL BE PERFORMED BY A CERTIFIED TEST AND BALANCE CONTRACTOR. A GREASE EXHAUST DUCTWORK SYSTEM. ACCESS PANELS SHALL BE INSTALLED 5. GENERAL CONTRACTOR SHALL PROVIDE ADDITIONAL 4 FT.
<br /> CERTIFIED TEST AND BALANCE CONTRACTOR CAN BE FOUND BY VISITING: 5. OPPOSED BLADE DAMPER T-BAR FOR DIFFUSER FRAMING M1 ALL SUPPLY AIR DIFFUSERS SHALL BE INSULATED TO PREVENT
<br /> HTTP://WWW.AABCHQ.COM/DIRECTORY IN ACCORDANCE WITH THE INSULATION MANUFACTURERS INSTALLATION 6. BLANK-OFF PANEL AS SHOWN ON 6. DOOR GRILLE SHALL BE INSTALLED BY DOOR CONDENSATION.
<br /> INSTRUCTIONS AND SHALL BE LABELED AS FOLLOWS: ACCESS PANEL - DO 1.D. INSIDE DIMENSION DUCTWORK PLAN
<br /> HTTP://WWW.NEBB.ORG/DIRECTORY.HTM MANUFACTURER. GRILLE SHALL BE LOCATED 12" FROM
<br /> NOT OBSTRUCT". 7. PLASTER FRAME MAY BE ANY DUCTWORK THAT PASSES THROUGH THE INDICATED DRAFTSTOP
<br /> HTTP://WWW.TABBCERTIFIED.ORG/SITE/CONTENT/CONTRACTORS/SEARCH NECESSARY - COORDINATE WITH BOTTOM OF DOOR M2 WALL MUST BE HARD DUCTED THROUGH THE WALL WITH AN AIR
<br /> 6. ALL HORIZONTAL GREASE EXHAUST DUCTWORK SHALL BE INSTALLED WITH A KEI KITCHEN EQUIPMENT INSTALLER DECOR DRAWINGS 7. AIR DEVICE FINISH WILL VARY: TIGHT SEAL AROUND THE DUCTWORK.
<br /> 7. UPON COMPLETION OF THE PUNCHLIST, THE MECHANICAL CONTRACTOR AND MINIMUM Y4" PER FOOT SLOPE AND SHALL BE PITCHED BACK TOWARD THE 8. 1" FILTER MEDIA KITCHEN, STORAGE, RESTROOMS - WHITE
<br /> TEST AND BALANCE CONTRACTOR SHALL SUBMIT REDLINED OR AS-BUILT * DINING ROOM, VESTIBULES - WHITE, BLACK OR EXTEND EXISTING SUPPLY AND SUCTION REFRIGERATION LINES TO
<br /> DRAWINGS ALONG WITH THE TEST AND BALANCE REPORT AND ALL EQUIPMENT
<br /> HOOD. 10 9. 120V POWER MODULE WALL-MOUNTED LED DISPLAY PRINTABLE PRIME COAT (COORDINATE FINAL COLOR WITH M3 RELOCATED BEVERAGE BAR ICE MACHINE.
<br /> OPERATION AND MAINTENANCE MANUALS TO THE McDONALD'S AREA KES KITCHEN EQUIPMENT SUPPLIER 1 . DECOR PLANS).
<br /> 7. UPBLAST KITCHEN EXHAUST FANS SHALL BE LOCATED A MINIMUM OF 6 FT. THERMOSTAT w
<br /> CONSTRUCTION MANAGER. A MINIMUM OF TWO (2) COPIES SHALL BE RELOCATE EXISTING FAN/LIGHT COMBO TO RELOCATED JANITOR'S
<br /> PROVIDED, ONE (1) FOR REGIONAL RECORDS AND ONE (1) FOR THE FROM ANY PARAPET WALL OR ADJACENT STRUCTURE AND SHALL TERMINATE A w
<br /> M4 CLOSET. IF REQUIRED REPLACE EXISTING FAN/LIGHT COMBO WITH
<br /> RESTAURANT. MINIMUM OF 40 INCHES ABOVE THE FINISHED ROOFING MATERIAL. MC MECHANICAL CONTRACTOR NEW.
<br /> REFRIGERANT PIPING: EXTEND EXISTING HARD DUCT TO FAN LIGHT IN RELOCATED
<br /> 8. ALL PENETRATIONS OF FIRE-RATED WALLS SHALL BE FIRESTOPPED WITH AN 1. ALL REFRIGERATION WORK SHALL BE PERFORMED BY A CERTIFIED M5 JANITOR'S CLOSET. � w
<br /> APPROVED AND LISTED FIRESTOPPING SYSTEM. REFRIGERATION CONTRACTOR. 0/0 OWNER/OPERATOR ft�
<br /> ❑ EXISTING STEADY STATE SPEED CONTROLLER FOR CEILING MOUNTED
<br /> VENTILATION SYSTEMS: 2. ALL REFRIGERANT PIPING SHALL BE SEAMLESS COPPER TUBING OF TYPE L IN M6 EXHAUST FAN TO BE RELOCATED TO RELOCATED JANITOR'S CLOSET.
<br /> 1 . ALL SHEET METAL DUCTWORK SHALL BE FABRICATED AND INSTALLED IN ACCORDANCE WITH ASTM B 88 AND ALL JOINTS SHALL BE SOLDERED. PC PLUMBING CONTRACTOR STEADY STATE SPEED CONTROLLER SHALL BE INSTALLED OVER paoFess�a
<br /> ACCORDANCE WITH LOCAL CODES AND SMACNA STANDARDS. SUSPENDED CEILING FOR ACCESS. DO NOT INSTALL OVER AREAS
<br /> 3. ALL REFRIGERANT SUCTION LINES SHALL BE INSULATED WITH A MINIMUM WITH DRYWALL CEILINGS.
<br /> 2. ALL DUCTWORK DIMENSIONS ARE INTERNAL FREE AREA DIMENSIONS AND SIZED 1 -1/2" FOAM PIPE INSULATION. PIPE INSULATION INSTALLED OUTDOORS RC REFRIGERATION CONTRACTOR s m
<br /> FOR 0.1" W.C. PER 100 FT. OF DUCT. SHALL BE PROTECTED WITH AN APPROVED WEATHERPROOFING MATERIAL.
<br /> 3. ALL SHEET METAL DUCTWORK SHALL BE CONSTRUCTED IN ACCORDANCE WITH 4. ALL SUSPENDED REFRIGERANT PIPING SHALL BE SUPPORTED AS FOLLOWS: ofAt+f NCAU�-3
<br /> SMACNA TABLES FOR 2" W.C. AND SHALL BE SUPPORTED WITH AN APPROVED MATERIAL MAX. HORIZ. SPACING MAX. VERT. SPACINGtick
<br /> HANGER AT INTERVALS NOT EXCEEDING 10 FT. COPPER TUBING <1Y4" 6 FT. 10 FT. 0 of
<br /> 4. ALL DUCT DROPS INTO THE BUILDING SHALL BE INSTALLED WITH FLEXIBLE COPPER TUBING >1Y2" 10 FT. 10 FT.
<br /> CONNECTIONS TO ISOLATE THE DUCTWORK SYSTEM FROM NOISE AND a j
<br /> VIBRATION. FLEXIBLE CONNECTIONS SHALL BE TESTED IN ACCORDANCE WITH 5. ALL PIPE INSULATION SHALL BE PROTECTED FROM DAMAGE FROM PIPE z
<br /> UL 181 AND LISTED AS CLASS 0 OR CLASS 1. HANGERS. PROTECTION SHALL BE LIGHT GAUGE GALVANIZED STEEL OR W , 0
<br /> EQUAL. w
<br /> 5. ALL DUCT DROPS INTO THE BUILDING SHALL BE OFFSET AS NECESSARY TO °
<br /> ALLOW FOR THE CLEAR INSTALLATION OF THE EXTERNAL DUCTWORK 6. ALL REFRIGERANT PIPING SYSTEMS SHALL BE PRESSURE TESTED FOR LEAKS a
<br /> INSULATION. PRIOR TO START-UP. ALL LEAKS SHALL BE REMEDIED PRIOR TO BUILDING
<br /> 6. ALL DUCTWORK BRANCHES SHALL BE SUPPLIED WITH A VOLUME DAMPER FOR TURNOVER.
<br /> BALANCING. VOLUME DAMPER SHALL HAVE A 2" OFFSET TO ACCOMMODATE CO2 DETECTION EQUIPMENT:
<br /> EXTERNAL INSULATION. 1. THE CO2 DETECTOR SHALL BE HARD-WIRED TO PREVENT TAMPERING AND ILI.
<br /> SHALL BE INSTALLED AT 12" A.F.F. WITHIN A 5 FT. RADIUS OF THE CO2 W
<br /> 7. TAKE-OFFS FROM RECTANGULAR TO ROUND DUCT SHALL BE DUCTMATE STORAGE TANKS. O O } a) E
<br /> STRAIGHT-SIDED OR CENTER HIGH-EFFICIENCY TAKE-OFFS WITH A 2" DAMPER WOMEN'S 0°
<br /> STAND-OFF TO ACCOMMODATE FOR EXTERNAL INSULATION. 2. ONE (1) AUDIBLE AND ONE (1) VISUAL ALARM SHALL BE INSTALLED A 102 o O a
<br /> Of Q u o
<br /> MINIMUM OF 7 FT. A.F.F., IN PLAIN SIGHT IN THE SAME ROOM AS THE CO2 CL
<br /> 8. ALL DUCTWORK JOINTS, LONGITUDINAL AND TRANSVERSE SEAMS SHALL BE STORAGE TANKS. o 3
<br /> SEALED WITH WELDS, GASKETS, MASTICS (ADHESIVES), TAPES, ETC. ALL
<br /> SEALANT MATERIALS SHALL BE LISTED IN ACCORDANCE WITH UL 181A OR 3. ONE (1) AUDIBLE AND ONE (1) VISUAL ALARM SHALL BE INSTALLED A
<br /> 181B. MINIMUM OF 7 FT. A.F.F., AT THE BACK OF THE KITCHEN AND IN PLAIN O O O O O O o �, o
<br /> SIGHT FROM THE MAIN SIDE OF THE PREP LINE.
<br /> N
<br /> 9. ALL SUPPLY AND RETURN SHEET METAL DUCTWORK LOCATED WITHIN THE o 3 0 ° o N o N
<br /> a ° O �� � O0
<br /> CEILING SPACE SHALL BE EXTERNALLY INSULATED. INSULATION SHALL BE 2" NATURAL GAS SYSTEMS (IF APPLICABLE): REEZER ` °
<br /> ° •L d Q _5
<br /> THICK MICROLITE XG-100 BY JOHNS MANVILLE OR EQUAL. 1. ALL GAS PIPING, WATER HEATER VENTS, INTAKES AND FLUES SHALL CONFORM U) J L a L 0 °
<br /> TO THE CURRENT VERSION OF NFPA 54, NATIONAL FUEL GAS CODE, AND ANY ° J
<br /> 10. ALL SUPPLY AND RETURN SHEET METAL DUCTWORK LOCATED OUTSIDE OF THE LOCAL CODE REQUIREMENTS. MEN'S o ., Cc: 3 ° N
<br /> SUPPORT
<br /> BUILDING SHALL BE INTERNALLY LINED WITH A 1 " THICK FIBERGLASS (MIN. 104 0 0 ° a '
<br /> R-4.2) AND EXTERNALLY INSULATED WITH A 1Y2" THICK RIGID POLYSTYRENE, 2. THE NATURAL GAS MAIN PIPE SIZING IS BASED ON THE FOLLOWING: 0 103 Q ° : o N
<br /> POLYURETHANE OR POLYISOCYAN U RATE BOARD (MIN. R-7.5). INTERNAL A. MINIMUM SUPPLY PRESSURE AT THE METER OF 2 PSIG O 0 1 O O O °' o E o ` o
<br /> FIBERGLASS INSULATION SHALL BE LINATEX BY JOHNS MANVILLE OR EQUAL. B. 1 PSIG PRESSURE DROP FROM METER TO FARTHEST APPLIANCE R_1 oN o 04 o o
<br /> EXTERNAL RIGID BOARD INSULATION SHALL BE THERMAPINK BY OWENS C. 1,000 BTU PER CU. FT. OF NATURAL GAS @ ° _ o-0-F
<br /> CORNING OR EQUAL. EXIST. CFM 101 Q) 5 L° ° �, o °
<br /> 3. GAS PIPING RUN-OUTS TO EQUIPMENT ARE SIZED BASED ON THE FOLLOWING: V� �'o °
<br /> EXIST ID ° o,° N E' 0
<br /> 11 . ALL EXPOSED SPIRAL DUCTWORK SHALL BE INTERNALLY INSULATED TO A. SUPPLY PRESSURE AT THE REGULATOR OF 10" W.C. (Y4 PSIG) ;OGLER - - o " o'i- °- °
<br /> PREVENT CONDENSATION (MIN. R-4.3). INTERNAL INSULATION SHALL BE 1 B. 0.5" W.C. PRESSURE DROP FROM REGULATOR TO FARTHEST APPLIANCE (TYP) cn 0_c °
<br /> THICK SPIRACOUSTIC PLUS BY JOHNS MANVILLE OR EQUAL. C. 1,000 BTU PER CU. FT. OF NATURAL GAS 1 10 O O o J w o ° N
<br /> z m 41pe L
<br /> USTO ER q'16IUD
<br /> ° `
<br /> 12. ALL DUCTWORK PENETRATIONS THROUGH FIRE-RATED WALLS, BARRIERS OR 4. ALL NATURAL GAS PIPE SHALL BE SCHEDULE 40 CARBON STEEL PIPE WITH SERVICEEA ° °'
<br /> PARTITIONS SHALL BE PROTECTED WITH A FIRE DAMPER. THE PERIMETER OF MALLEABLE IRON FITTINGS AND SHALL BE COMPLY TO ONE OF THE O O O O a cn o 0
<br /> 100 rn- L.- o o- c
<br /> THE FIRE DAMPER SHALL BE FIRESTOPPED WITH AN APPROVED AND LISTED FOLLOWING STANDARDS: ASME B36.10, 10M; ASTM A 53; OR ASTM A 106. - Q ° o ° a)
<br /> ° a� Qoi L i E
<br /> FIRESTOPPING MATERIAL. 0 0 0 0 3° a
<br /> 5. NATURAL GAS PRESSURE REGULATORS SHALL BE MAXITROL 325 SERIES OR CONTRACTOR TO PROVIDE LO VERED O 0
<br /> 13. ALL EXTERIOR SHEET METAL DUCTWORK SHALL BE EXTERNALLY WRAPPED WITH EQUAL. RETURN BEHIND EACH MENU BOARD. rng 2-° rn aO
<br /> AN APPROVED WEATHERPROOFING MATERIAL TO PROTECT AGAINST WATER REFERENCE ARCHITECTURAL PLAINS FOR o o L o-T•�0 0
<br /> PENETRATION AND CORROSION. SIDES AND TOP OF EXTERNAL 6. ALL SUSPENDED STEEL PIPING SHALL BE SUPPORTED AS FOLLOWS: SECTION VIEW OF LOUVER INSTALLATION. O o ® , 3 0 °
<br /> -0
<br /> WEATHERPROOFING
<br /> WEATHERPROOFING SHALL BE ALUMAGUARD 60 MIL UV BARRIER BY MAX. HORIZ. SPACING MAX. VERT. SPACING Q N a o 0 N o
<br /> POLYGUARD OR EQUAL. BOTTOM OF EXTERNAL WEATHERPROOFING SHALL BE 6 6 w � o� o o� L
<br /> VAPORGUARD 5 MIL MEMBRANE BY POLYGUARD OR EQUAL. 3 „ O O O O 0 � ~ 3 w
<br /> /4 TO 1 8 FT. 8 FT.
<br /> 14. ALL FLEXIBLE DUCTWORK, METALLIC AND NONMETALLIC, SHALL CONFORM TO 10 FT. 10 FT. RELOCATE DIFFUSERS AS REQUIRED TO AVOID w
<br /> THE FOLLOWING: a - m w o °' O N
<br /> CONFLICTS WITH NEW LIGHTING. } o � w
<br /> A. 2" THICK INSULATION (R-6.0) 7. GAS PIPING SHALL NOT PENETRATE ANY FIRE-RATED CHASE OR SHAFT, 00 w O 0 � � __3 cc
<br /> B. INTEGRAL VAPOR BARRIER DUCTWORK OR PLENUM.
<br /> Z N w - N O N
<br /> aU c�i� � wJ ui a I
<br /> C. LISTED AND LABELED UL 181 , CLASS 0 OR CLASS 1 S-2 _
<br /> O 0 0 0 o � w � oo v �
<br /> D. INSTALLED IN ACCORDANCE WITH: 8. ALL NATURAL GAS PIPING INSTALLED OUTDOORS SHALL BE COATED WITH A OFFICE EXIST. CFM o v'
<br /> i. SMACNA STANDARDS, CORROSION RESISTANT PAINT. PAINT COLOR SHALL BE ORANGE OR YELLOW. 1108 KITCHEN
<br /> ii. AIR DIFFUSION COUNCIL INSTALLATION GUIDELINES, AND/OR Lff)- EXIST. "0iii. MANUFACTURER'S INSTALLATION INSTRUCTIONS 9. ALL INTAKE AND VENT PIPING FOR SEALED-COMBUSTION WATER HEATERS (TYP.)
<br /> SHALL BE PVC OR ABS, SHALL BE SIZED AND INSTALLED IN ACCORDANCE _
<br /> 14. FLEXIBLE DUCTWORK SHALL NOT PENETRATE WALLS. SHEET METAL DUCTWORK WITH THE MANUFACTURER'S INSTRUCTIONS AND SHALL BE INSTALLED BY THE
<br /> IS REQUIRED AT ALL FIRE-RATED AND DRAFTSTOP WALL PENETRATIONS. PLUMBING CONTRACTOR. o
<br /> M1
<br /> 15. ALL COVERINGS, LININGS AND ADHESIVES (TAPES, ETC.) SHALL HAVE A 10. ALL WATER HEATER VENTS SHALL BE LOCATED A MINIMUM OF 10 FT.
<br /> FLAME-SPREAD INDEX NOT GREATER THAN 25 AND A SMOKE-DEVELOPED HORIZONTALLY FROM ANY OUTDOOR AIR INTAKE. WHERE A WATER HEATER (TYP.)
<br /> INDEX NOT GREATER THAN 50. VENT IS LOCATED WITHIN 10 FT. OF AN INTAKE, THE FLUE OR VENT SHALL
<br /> TERMINATE A MINIMUM OF 2 FT. ABOVE THE INTAKE. Q
<br /> 16. DUCT-MOUNTED SMOKE DETECTORS SHALL BE INSTALLED IN SYSTEMS WITH u
<br /> DESIGN CAPACITY GREATER THAN 2,000 CFM. SEE MECHANICAL DRAWINGS
<br /> 11. UPON COMPLETION OF INSTALLATION, THE GAS PIPING SYSTEM SHALL BE
<br /> PURGED OF DELETERIOUS MATERIAL AND SHALL BE PRESSURE TESTED. U a o
<br /> FOR LOCATIONS OF SMOKE DETECTORS. DUCT-MOUNTED SMOKE DETECTORS Q z
<br /> ARE NOT REQUIRED WHEN THE BUILDING IS PROTECTED THROUGHOUT BY PRESSURE TESTING SHALL BE PERFORMED WITH THE EQUIPMENT SHUT-OFF m CD o z m
<br /> AREA SMOKE DETECTORS CONNECTED TOA FIRE ALARM SYSTEM WHERE THE VALVES IN THE CLOSED POSITION TO PROTECT EQUIPMENT FROM DAMAGE DUE z U w w
<br /> FIRE ALARM SYSTEM IS DESIGNED TO SHUT DOWN THE ROOFTOP UNITS. TO EXCESSIVE PRESSURE. - w
<br /> Q D vii
<br /> 17. ALL SUPPLY AIR DIFFUSERS SHALL BE INSULATED TO PREVENT CONDENSATION. 12. AFTER THE PRESSURE TEST HAS BEEN COMPLETED AND ANY LEAKS ORRFR (n o w o 3
<br /> REMEDIED, THE INSTALLING CONTRACTOR SHALL MEASURE AND VERIFY THE 07 w z 0 0
<br /> FOLLOWING GAS PRESSURES WHILE EQUIPMENT IS IN OPERATION: m ~ a
<br /> 18. ALL AIR DEVICES LOCATED IN DRYWALL CEILINGS SHALL BE SUPPLIED WITH AN z U- W
<br /> INTEGRAL VOLUME DAMPER ACCESSIBLE FROM THE AIR DEVICE FACE TO A. GRILL - 6" W.C. NATURAL, 14" W.C. L.P. U U J o
<br /> FACILITATE BALANCING. B. FRYER - 6" W.C. NATURAL, 14" W.C. L.P. LLJ z z o
<br /> C. WATER HEATER - 6" W.C. NATURAL, 14" W.C. L.P. o z °O
<br /> w o
<br /> 19. ALL OUTDOOR AIR INTAKES SHALL BE LOCATED A MINIMUM OF 10 FT. D. HVAC UNIT - 6" W.C. NATURAL, 14" W.C. L.P. un w o
<br /> HORIZONTALLY FROM ANY SOURCE OF CONTAMINATION SUCH AS EXHAUST � O >< vvi o X _
<br /> ui
<br /> FANS, PLUMBING VENTS, WATER HEATER FLUES, ETC. WHERE A CONTAMINANT 13. IF THE MINIMUM PRESSURES ARE NOT MET, THIS SHALL BE IMMEDIATELY N Wo
<br /> " `'� N o
<br /> SOURCE IS LOCATED WITHIN 10 FT. OF AN INTAKE, THE INTAKE OPENING REPORTED TO THE MCDONALD'S AREA CONSTRUCTION MANAGER.
<br /> SHALL BE LOCATED A MINIMUM OF 2 FT. BELOW THE CONTAMINANT SOURCE.
<br /> 1 MECHANICAL CEILING PLAN
<br /> w M100
<br /> mi .0 SCALE. 1/4" - V-0"
<br /> =
<br /> `n MECHANICAL CEILING PLAN
<br />
|