INSTALL 2019 - Laserfiche WebLink

Home Browse Search

SUBMERSIBLE PUMPING SYSLMS ;FranklinFuelingSystems I SUBMERSIBLE TURBINE PUMPS Specifications • Variable speed models are available in variable lengths only. • Check valve: 23/4" diameter fluorocarbon seal constructed with cast aluminum body and steel backing washer. • Pressure relief valve: available in four pressure relief settings, integral to check valve. Standard model relieves at 40 psi and resets above 35 psi. • Syphon: venturi-type syphon primer supplied with every submersible. Syphon check valve and secondary syphon sold separately. • Air eliminator: every submersible includes a tank return path with one-way check valve to provide active air elimination. • Electrical disconnect: electrical yoke for positive contractor disconnect during service. Pump Motor • 2 Hp or 4 Hp, variable speed, two-stage centrifugal type pump motor with integral, automatic, thermal overload protection. • Max. flow: VS2 = 110 gpm, VS4 = 140 gpm. • Max. pressure: selectable operating pressure on MagVFC" between 24 psi and 42 psi deadhead. • Available with MagShell'" which results in 45% increased flow area around motor. Approvals • cULus listed. • Consult factory for applicable approvals. 2 hp Variable Speed Turbine Performance Chari 140 30 !. __. i_._.. 1 - - Two MV52, Manifoltled 2 hp 120 - - .i -. - Mag5hell"Variable Speed Pumps 110 ._.. ----- ---- loo -- - ___100--- ------- r,..- 90 ._. y c80 ..... -. -.. _. -.�. .. 0 70 .... One .1112. 2 lipMagShell'" ...i...... _. _ ,s. • Variable Speed Pump n 60 .. 50 _ .. 40 .. •.� 30 20 . ......._ it 10 -... - 0 0 20 40 60 80 100 120 140 160 180 200 220 Flow In Gallons per Minute (gpm) Power Requirements • Variable speed pumps can only be controlled by a MagVFC`" variable frequency controller: • VS2 models can operate with single- or three-phase incoming power supply to the MagVFC'". • VS4 models require three-phase incoming power supply to the MagVFC'" for proper operation. • Incoming power supply to the MagVFC" can be 200-250 VAC, 50 or 60 Hz. • MagVFC— outputs a three-phase, variable frequency signal, valid for FE Petro" variable speed pumps only. • VS2 max. motor draw: 9 Amps. • MagVFC'" max. line draw: 20 Amps. Liquid Compatibility • Max. liquid viscosity: 70 SSU at 60 IF (15 IC). • STP variable speed models are UL and cUL listed for fuel mixtures containing up to 10% ethanol, and 20% MTBE, 20% ETBE or 17% TAME with gasoline. • IST variable speed models are UL and cUL listed for fuel mixtures containing diesel fuel with up to 20% biodiesel, 100% biodiesel, up to 85% ethanol with gasoline, and 20% MTBE, 20% ETBE or 17% TAME with gasoline. • All variable speed (non -AG) models can also be used with diesel fuels, fuel oils, kerosene, Avgas and jet fuels in a non -gelled pourable state. • All wetted elastomers are made of a high grade, fluorocarbon compound. Quality Certification • Franklin Fueling Systems is an ISO 9001 Certified Manufacturer. 4 hp Variable Speed Turbine Performance Chart 140 - I - -_ i ..__ ____ 130 ._ i I ._ .... L - _ _i .._....1.. .. Two MVS4. Manilolded 4 hp 120 - r Ma9$heA"' Variable Speed 1 -) i Pumps 110 .... 100 ;. \ '....... _� 90 .. -,.. t' V • 70 x One MV54 4 hp MagShell"- o 60 o Variable Speed Pump _..; . 5040 I I I J 30 I r to 0 0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 Flow in Gallons per Minute (gpm)