Laserfiche WebLink
A tight or driving fit will forme the drive shaft Note: For 11rowers using the external lube <br /> out of its normal position and cause internal system, the oil sump capacity is 71/2 gallons and <br /> damage. A loose fit will probably result in shaft oil change interval can be 4-6 months. <br /> damage or breaking. The motor sheave must 11@Rt <br /> Ga1)CM00 Cf/1C <br /> 4O <br /> also fit correctly and be properly aligned with <br /> the blower sheave. <br /> Adjust motor position on its sliding base so t <br /> that belt tension is in accordance with drive <br /> manufacturer's instructions. Avoid excessive <br /> belt tension at all times. Recheck tension after <br /> the first ten hours of operation and periodical- <br /> ly thereafter to avoid slippage and loss of periodical- <br /> OIL LM C ' <br /> (1I GCI CND/Cw1C <br /> MINt�IN OIC U� <br /> blower speed. """'N"°`°" "� <br /> MAKTIC OIC DAMN KNR <br /> I l)[/01[MD lu1C <br /> Check blower after installation and before ap- <br /> plying power by rotating the drive shaft by hand. VERTICAL AIR FLOW ' <br /> If it don not rotate freely, look for uneven INDI' .,al<FILL <br /> (11 teal 00 COV"mounting, piping strai , excessive belt tension, <br /> or coupling misalignment. Check blower at this • <br /> —71 <br /> time to insure oil was added to reservoirs. rAIN®Q <br /> _r_ _ .uN <br /> Lubrication I WHIG <br /> Oil D AA <br /> V((NIN W(Om ANCA <br /> REvery M D Pneumatic Blower is factory E"�0QA"`�' <br /> I ae e(at elleec <br /> tested, oil drained, and shipped dry to its 1LTEANATC OIL LVM K11C <br /> (21 Ga IND/MIC <br /> installation point. Both independent oil reser- ,n tna$Tom a1Aa Nh otc INION KIOC <br /> (1 101O C Ex (I 1 GCI G•M <br /> 01 CIIt <br /> voirs must be filled to proper level before SNINTNINOIL LM <br /> "(THIN NDTCICN MG <br /> operation. <br /> Shaft bearings at the gear end of the blower HORIZONTAL AIR FLOW <br /> are splash lubricated by one or both gears dip- <br /> ping into an oil reservoir formed in the end plate <br /> and cover. Shaft bearings at the free end of the i Nn Flu,CNN <br /> blower are lubricated by a slinger assembly dip- G0100 <br /> ping into an oil reservoir. Before starting the 1 <br /> blower, fill sumps as instructed below: QQ - GILL CC(.,T. K 11 GCI oo MAN - <br /> I <br /> 1. Remove fill plugs or breathers from gear IN <br /> end and free end covers. :=F �TM�:'»M 4 MEN <br /> 2. Pour oil through fill hole slowly until oil `-� -1- "`"""""'(" <br /> If AGID S K <br /> appears in oil sight glass. Slowly bring oilLI IN WI'C COIL/�M'TN PLUS <br /> up to proper level. See figure 4. <br /> 3. Replace plugs or breathers in end covers <br /> (64/67 series does not have breathers.) GAS SERVICE <br /> M D Pneumatics recommends a good grade <br /> �"•"a"`R� <br /> industrial type non-detergent oil (heavy duty <br /> type). Recommended oil viscosity as follows: <br /> Ambient Temperature 1 <br /> A. Winter Aeroshell65 I o <br /> B. Summer Aeroshell 80 <br /> DK CCM.ACTIONS CDT- <br /> (11 C/GI CSN/MIC <br /> Lubrication should be checked every 24 I <br /> hours of operation. Time lapse between oil BLOWER W/ EXTERNAL <br /> changes will have to be determined for each in- LUBE CONNECTIONS <br /> dividual installation and normally will be be- <br /> tween 250-1000 operating hours. FIGURE 4 <br /> 5 <br />