INSTALL 1990 - Laserfiche WebLink

Home Browse Search

IIII■1111. III Extractor Fiffngsi �r 0 MAY 19PW 233 series 9? 233 Series Extractor fittings allow foot valves and ball float vent ' I NMENTAL HT les to be removed from under- RMIT/SERVICEoround tanks without breaking upthe —� concrete. See pg. 12 for OPW extractor wrench selection. s - Dimensions OPW 233-E 1'/2"Size OPW 233-E ®PW .233-P Top thread 4" The 0 P 233-E Extractor f itting is for The OPW 233-P Extractor fitting has Outlet thread 1'/2" use with any 11/2' foot valve with a internal threads to accept a cohnecting Inlet male thread 4" maximum outside diameter of 23/4". nipple between the extractor and the Inlet female thread 1'/2" The 233-E has 4"male thread for con- tank flange, which provides an option Maximum clear I.D. nection to 4"tank flange and is gas- to adjust the elevation of the 233-P in through valve 27/8 ket-sealed to prevent loss of prime, relation to the tank. The cage of the caused by air being sucked in through 233-P is easily replaced because it is OPW 233-P 2"Size the top fitting. threadless-it is simply lifted out like a bottle cork. Top thread 4" Materials Outlet thread 2" Body: cadmium plated cast iron Materials Cap and suction stub adaptor:bronze Body: cast iron Inlet thread 4'" Gasket: chromed tanned leather Cage: bronze Cage thread 2"' SIZE: 1 I/2 WT.: 20.22 lbs. Seals: buna-N O-ring Maximum clear I.D, 233-E-4040 SIZE: 2 WT.: 18.00 lbs. through valve 31/2" 233-P-6050 ®PW 233-V ®PW 233-VMP and The OPW 233-V Series Extractors are used to hold and - 233-VP Test Plugs posit'Qn the OPW 53-V Series Float Vent Valves in the OPW Test Plugs are used to isolate the underground storage tank.It is furnished complete with tank from the vent piping system during an extractable cage.The entire Float Vent sub-assembly tank testing. can be extracted from the tank by using either an OPW The 233-VP plug is used on: 52 or 89 Extractor Wrench, for tank testing. 233-V-4420 (4" x 2"). The OPW 233-V extractor is a single outlet extractor used 233-VM-4422 (4" x 2" x 2") in non-manifolded vapor recovery systems, or systems The 233-VMP plug is used on: such as shown on p. 7. 233-V-4420 (4" x 2") Materials: 233-VM-4422 (4" x 2" x 2") Body: cast iron w/Duragard" coating 233-VM-6045 (4" x 2" x 3") Extractor: bronze SIZE: 4" x 2" WT.: 15.33 lbs. 233-V-4420 233-VP-6046 WT.: 78 lbs. 233-VMP-6047 WT.: 1.24lbs. ®PW 233-VM Dimensions The OPW 233-VM extractor is a multi-outlet extractor, 233V 233VM 233VM available in 2 sizes; used in direct manifolded systems, 4420 4422 6045 vapor recovery, or where provision for Stage 11 Vapor (Tee) (Cross) (Cross) Recovery is needed. Top Thread 4 4 4 SIZES:4" x 2" x 3" WT. 18.73 lbs. 233_VM_f�0_45 Outlet Thread 2" 2" 2" 4" x 2" x 2" WT. 16.62 lbs. 233-VM-4422 j 2„ 3"" All OPW 233-V series extractors are specially coated with black Duragard'" coating, for improved corrosion TanThread c- 4 resistance and easier cage removal, tion Thread 4" 4"