Laserfiche WebLink
MIR 1M VERIFICATION LABORATORY AN. .'SIS <br />TANK <br />TANK <br />TPH-G <br />TPH-D <br />BTX & E <br />CL HC <br />TOTAL <br />MTBE <br />OXYGEN <br />ATES <br />METAL <br />PCB <br />11 <br />CONTENTS <br />8015 <br />8015 <br />8020 <br />8010 <br />LEAD <br />8020 <br />(MTBE, <br />ICRP/ <br />8270 <br />8260 <br />8260 <br />8260 <br />8240 <br />7420 <br />8260 <br />TBA,DIPE, <br />AES or <br />8080 <br />8260 <br />7421 <br />ETBE, <br />AA <br />TAME) <br />8260 <br />LEADED GAS <br />X <br />X <br />X <br />X <br />UNI, GAS <br />X <br />X <br />X <br />DIESEL <br />X <br />X <br />KEROSENE <br />X <br />X <br />X <br />UNK FUEL.. <br />X. <br />X <br />X <br />..X <br />X <br />PROD. OIL <br />X <br />X <br />X <br />CHLOR. <br />SOLVENTS <br />X <br />X <br />X <br />NONCHLOR <br />SOLVENTS <br />X <br />X <br />X <br />WASTE\ <br />USED OIL <br />X <br />X <br />X <br />X <br />X <br />X <br />X <br />All analysts methods are the designated EPA methods described in EPA SW 846, Third Edition. Those methods not found in SW 846 are <br />specifically noted below. Refer to the "SWRCB LUFT Field Manual", Appendix D (B), Table 3-5 on page A20 for minimum detection <br />limits for motor vehicle fuel (gasoline and diesel). Refer to "Tri -Regional Board Staff Recommendations for Initial Evaluation and <br />Investigation of UST's" for the waste and motor oil minimum detection limits. Detection Limits that remain below the MCL, STLC or <br />Allowable Limit of the contaminant in question will be accepted, however laboratory shall utilize the most conservative method. <br />LABORATORY ANALYSES TERMINOLOGY: <br />TPH-G.. Total Petroleum Hydrocarbon, Gasoline, GC/FID (5030) 8015 mod or GC/MS 8260 . . <br />TPH-D . Totel Petr6leuin Hydr6carbon, Diesel; GC/FII) (3350}, 8015 mod or GC/MS 8260 <br />BTX & Benzene; Toluene, Xylene & Ethyl Benzene, GC/PID 8020 or GC/MS 8260 <br />CL HC Chlorinated Hydrocarbon, GC/HSD 8010, GC/MS 8240 or 8260 <br />TOTAL LEAD Total lead, AA 7420, AA 7421 or ICP -AES 6010 <br />OXYGENATES MTBE, ETBE, TAME, DIPS, & TBA GC/MS 8260 (For MTBE screen only you may use 8020) <br />METALS ICAP or AA Inductively Coupled Plasma Atomic Emission Spectrometry 6010 or Atomic Absorption Spectrometry 7000. <br />Cadmium, Chromium III and V1, Lead, Zinc and Nickel. <br />PCB Polychlorinated Biphenyls, GUMS 8270 or 8080 <br />GC -FID Gas Chromatography, Flame Ionization Detection <br />Method 3050 Acid digestion <br />Method 3540 Soxhlet sample preparation <br />Method 3550 Sonication sample preparation, extraction method <br />Method 5030 Purge and trap sample preparation <br />QA/QC Quality Assurance/Quality Control <br />Metals: <br />Notes: To avoid false positive detection of benzene, benzene -free solvents are to be used. Fused capillary columns are preferred to packed columns; a <br />packed column may be used as a "first cut" with "dirty" samples or once the hydrocarbons have been characterized and proper QA/QC is followed. For <br />drinking water sources, EPA recommends that the 500 series for volatile organic should be used in preference to the 600 series because the detection. <br />limits are lower and the QA/QC is better. Samples exhibiting any level of heavy metal contamination may require further analysis. PHS-EHD <br />recommends holding those samples until disposal is indicated. <br />EH 23 046 (Revised 05/09/00) <br />