COMPLIANCE INFO_2019 - Laserfiche WebLink

Home Browse Search

waste. If the leak cannot be corrected the spill contain- Height Adjustment Bolt er or bellows should be replaced . As an alternate to a hydrostatic test a vacuum test can be performed on the spill container. Using OPW DW-VAC- TEST and SC-TEST, perform a vacuum test on the spill con- tainer. An initial vacuum of 15" of water should be attained e� and the spill container must retain a vacuum of at least 12 " f\ Shims of water after 5 minutes. (See DW-VAC-TEST Instructions.) Cap Step 9: (See Figures 2 & S) Before pouring concrete, place plastic over the cover and Mounting Ring protecting them from concrete splash . Adaptor Double check that the unit is level and at proper grade height. Pour concrete per Figure 5 . Ramp or dome the Figure concrete away from the mounting ring . There should be a minimum of 1 " slope to finish grade. Slope V Down From Top of Mounting Ring NOTE: Do not stand on spill container before concrete sets UP* Finish Grade Remove plastic from cover after concrete has dried . Remove adjustment system . Re-test the spill containers for leaks as described in Step 8, after the concrete has setup. ��®° • '.epItit Operation and Maintenance: > • : '> <•. p — 01 .1 Y ' 'e 1 0. It IY i Y Y e Y After each fuel delivery, the operator must remove any stand- ` •` ` •Q • o` :`�.." ' ; : :':`. .. a ` • ' e • ing fuel from the container. Fuel can be removed by actuat- A .:. . . > . . . :ji > ; .ami. : f e t++. ° a • 1,.d. . " Q, o •. e+•y. ing the drain valve or with a gasoline absorbing disposable � . , � • ° ` . Y �. . t ; vY towel . If access to drop tube or overfill valve is required re- e , t a . . aIt a move Nipple Adaptor from primary bucket. ,a r `� o a " ;3 .• 6,4110i > r kit " b i�!•.: 4 a , �`a • .t,'.8`. . p . 1 'fo',Q., Weekly* Perform a visual inspection of the interior of the con41 - tainment bucket for water or other contaminants . If water or Figure s other contaminants are found they must be disposed of with disposable towels. Dispose of towels safely and per all appli- cable local, state and federal codes. Check that cover is in z good condition and properly identified . Replace cover and seal as necessary. Inspect the bucket walls for cracks, bulges i , _ or holes . If any exist, have that spill container barricaded and 4 Min Clearance contact maintenance personnel immediately for repairs. o T , 0 a PNOTE: The bellows and base on the spill container can be o replaced if damaged, It � i Semiannually: Follow all state and local required hydrostatic ft , or vacuum testing on the buckets . Inspect and clean the inte- .:`' - t ! rior of the spill container and drain valve screen . Remove acr ' 4 A cumulated dirt and grit. Where applicable, test the drain valve using CARB procedure TP-201 . 1 C or TP-201 . 1 D. if the 171 " drain valve passes testing no further maintenances required . If Ref 5 the drain valve fails testing, remove the valve, soak in water frJ}{ and use high-pressure air, if needed, to clean . Reinstall the �fL- ---•I - p �` i a -" drain valve to its proper position and where applicable, test �� tr f the valve with CARB procedure TP-201 AC or TP-201 . 1 D. If problems persist, replace the drain valve with P/N 1 DK-2100 .r� EVR (specified torque 11 .5 ft-lbs min to 13 .5 ft-lbs max, 5/16- —' �- 18 UN thread) . The sealable cover 0 SC) adjustment nut is set i 4 at the factory, but due to environmental conditions it may be necessary to adjust it to either improve sealing or ease cover Length of Nipple = Dimension A - Dimension B - Dimension C - 2" Min removal . Figure 6 IMPORTANT: Leave these instructions with the Station Operator.