INSTALL 1999 - Laserfiche WebLink

Home Browse Search

r >i� �� Specifying Accessory Components T s ? = zK Flexible Isolation Tube 3 x 2 Reducer Seal If dielectric isolation of the flexible If the Flexible Isolation Tube Is connectors are required order one required to seal,at its lower end, Flexible Isolation Tube.for each directly to 2' pipe instead of 3' pipe entry. This isolation tube pipe,then this rubber reducer seal comes equipped to attach directly is required to make this transition. to the base of the Pipe Entry Boot This rubber seal can be used In at one end and connect to 3-pipe place of a Pipe Entry Boot when at the other end. Incudes a 30- circumstances require 2' rigid rubber lube and two band clamps. pipe entering directly into the pan. Also available in a 42' long tube which has its own air valve stem. Conduit Entry Seals Drain Fitting Kit These rubber seals are used to Should the pan be required to be >. seal conduit which enters the drained into the secondary piping bottom of the pan through the system then the Drain Fitting Kit conduit entry cuffs. Specify the should be installed. This kit size of the conduit when order. includes all the necessary ?<; ing these rubber seals. There _. _ components to connect the pan to :; z@ are three sizes available: ithe Flexible Isoaltion Tube with a 1/2'nylon drain tube. The Petr0- 1/2': -1/2': CES-1550 Trip Kit can not be used in this 3/4": CES-1575 Application. < 1": CES-1510 Flexible Boot Adapter Stage II Entry Boot In the event that a Flexible Entry The Stage 11 Entry Boot used for •'` Boot is required to be installed in "` pans which provide a stage II �;,•,..c> ;N :;;;;. the bottom ofAhe pan, to seal a - entry cuff in the location of the ` stege II vapor recovery pipe entry, "^ stage It pipe entry. The assembly . . then this adapter permits the ^<?#p:i ?:: includes a 7-long rubber entry isolation tube to be connected to boot with air valve stem,a 3-to 1- the outside base of the Flexible cs.:>::z':i rubber reducer and and two band Envy Boot. For more information clamps. This boot is permits a about this application contact your `?': 's`':# Flexible Isolation Tube to be local distributor or Environ. ? zr connected to it's base for isoiation ` '•%'?`r of a flexible connector. Petro-Trip Kit Trip Sensor Switch Should automatic shut-of of the Should automatic shut-off of the shear valves be required, in the electronic dispenser be required event of product collecting in the in the event of a product leak into base of the pan, then specify the the pan, the Trip Sensor Switch Petro-Trip Kit. This device is a should be ordered. This switch is spring loaded sensor which willactivated when the Petro-Tnp . . engage and trip the shear valve engages and will automatically cut lusable link in the presence of the power to the dispenser. gasoline in the pans collection well. Kit accommodates up to four shear valves. Sensor Stabilizer lube Remote Draining System If a electronic leak detection A remote draining system Is >.:•:: sensor is to be installed inside the available for the dispenser pans ry%:��%�r:$i��;::>:::%•`:::y:E:E;•i Pan for monitoring the Sensor which will drain any leaking `•x•;>;•.i.>.;:.;:;:::;•.:;.:.•,;:.: Stabilizer Tube will secure the product away from the dispenser sensor in an upright position to a remote collection sump. This directly over the collection well. system has a number of The sensor should be no larger components, such as, a primary than 2.125' in dia.. The tube is and secondary drain line, drain made of stainless areal wire mesh fittings,tee fittings and a collection and comes with a mounting sump,which are all described in bracket to be secured to the pan's more detail on page 9. stabilizer bar. 2