COMPLIANCE INFO - Laserfiche WebLink

Home Browse Search

Appendix CC HOW TO LOCATE THE POSITION OF THE 71 SO FOR COMPLETE SHUT- OFF AT A GIVEN TANK CAPACITY Note: This Appendix only applies when AHJ require- EXAMPLE ments call for complete shut-off at a given tank capacity . 1 . For an Owens-Corning Model G- 3 Fiberglass ° Tank See page 4 for standard measurements , Calibration Chart: The length of the upper tube and the placement of the Tank Capacity - 10, 000 gal ., nominal 9,403 gal . 71 SO valve body determine the shut-off point. The sam- NOTE : Use actual capacity only ple calculation below will provide for complete shut- off at 95 % . In all cases, the upper tube length must be a Tape measure minimum of 6- 1 /2 " plus the length of the riser pipe . All length measurements are in inches . ��— INSTRUCTIONS 1 . Find the tank capacity ( in gallons) from the tank cali - bration chart provided by the tank manufacturer . Riser Pipe 2 . Calculate 95 % of capacity. with Face (A) Seal Adaptor To Tank (B ) 3 . Locate the 95 % volume number on the tank calibra - Top (I . D. ) To Tank tion chart . Bottom 4 . Find the dipstick number (X) which corresponds to the 95 % tank volume . And, find the dipstick number (Y) which corresponds to the 100% volume . 5 . Subtract the dipstick number (X) from the tank diam - eter (Y) to find the upper tube reference number (Z) . (Y) - (X) = (Z) 2 . 95 % of actual tank capacity = 0 . 95 x 9403 gal . _ 6 . Add 1 . 5 " to (Z) to find the upper tube depth E . 8933 gal . (Z) + 1 . 5 " = E 3 . The closest number which is less than 8933 gal . Is 7 . Is E less than 6 - 1 /2 " 7 8910 gal . Choosing the closest number less than 95 % of actual capacity ensures that complete NO Upper tube length is E plus the distance from the shutoff will occur when the tank is no more than top of the Face Seal Adaptor installed on the riser 95 % full . pipe to the inside, top lip of the storage tank (A) . Upper Tube Length - E + (A) 4 . The calibration chart reading of 8910 gal . corre - sponds to a dipstick measurement of 82 " . For testable models only, ending in " T" . 5 . Dipstick number (X) = 82 " Upper Tube Length = E + ( A ) - 1 - 1 /2 " Tank diameter (Y) = 92 " (Y) - (X) _ (Z) (92 " - 82 " = 1011 ) = 10 " YES Upper tube length is 6- 1 /2 " plus the riser pipe (Z) measurement (A) . 6 . (Z) + 1 . 5 " = E ( 10 " + 1 . 5 = 11 .5 ") Upper Tube Length = 6- 1 /2 " + (A) E = 11 . 5 " 7 . Is 11 . 5 " less than 6- 1 /2 " ? For testable models only, ending in "T" : NO Measure the distance from the top of the FSA-400 Upper Tube Length - 6 - 1 /2 " + ( A ) - 11 /2 " Face Seal Adaptor installed on the riser pipe to the inside, top lip of the storage tank and obtain measurement (A) . NOTE : You must find the actual tank capacity num - Upper tube length - E + (A) ber that correlates to the 6- 1 /2 " + (A) depth for the station records. This number may also be used or For testable models only, ending in "T" : the purposes of calibrating an electronic tank level Upper Tube Length - E + ( A ) - 1 - 1 /2 " system . 23