COMPLIANCE INFO - Laserfiche WebLink

Home Browse Search

waste. If the leak cannot be corrected the spill contain- Height Adjustment Bolt er or bellows should be replaced. � As an alternate to a hydrostatic test a vacuum test can be performed on the spill container. Using OPW DW-VAC- TEST and SC-TEST, perform a vacuum test on the spill con- tainer. An initial vacuum of 1 S" of water should be attained and the spill container must retain a vacuum of at least 12" 4• Shims of water after 5 minutes. (See DW-VAC-TEST Instructions.) Cap -- Step 9: (See Figures 2 & S) Before pouring concrete, place plastic over the cover and Mounting Ring protecting them from concrete splash . Adaptor Double check that the unit is level and at proper grade height. Pour concrete per Figure 5 . Ramp or dome the Figure concrete away from the mounting ring . There should be a minimum of 1 " slope to finish grade. Slope 1 " Down From Top of Mounting Ring NOTE: Do not stand on spill container before concrete sets up• Finish Grade Remove plastic from cover after concrete has dried . Remove adjustment system . Re-test the spill containers for leaks as � `' +,+: +;• : . described in Step 8, after the concrete has set up Operation and Maintenance: y . . • �1:�. • +tea . r iii . t '��:��. After each fuel delivery, the operator must remove any stand- ` Ni Now ` 4i` ` ` •` ` •` ' • ` •' Ing fuel from the container. Fuel can be removed by actuat- Z a .z ing the drain valve or with a gasoline absorbing disposable , .,�`� , i .1 . � `tiw, . ` tti++` ' .. `y'i`IN towel. If access to drop tube or overfill valve is required re- . � . 3 � ,•, .t � move Nipple Adaptor from primary bucket. a Z . . . .: a v . ,�>•,, � • � � �.,. + • . ty'a•; . .a��. ,I NI I IL IN Weekly: Perform a visual inspection of the interior of the con- tainment bucket for water or other contaminants. If water or Figure s other contaminants are found they must be disposed of with disposable towels. Dispose of towels safely and per all appik cable local, state and federal codes. Check that cover is in NIN good condition and properly identified . Replace cover and s seal as necessary. Inspect the bucket walls for cracks, bulges lip or holes. If any exist, have that spill container barricaded and r" Min Clearance contact maintenance personnel immediately for repairs . ; , NOTE: The bellows and base on the spill container can be ® "c�t ` o x C replaced if damaged. } a 1 IT �" Semiannually: Follow all state and local required hydrostaticB or vacuum testing on the buckets. Inspect and clean the inte- rior of the spill container and drain valve screen . Remove ac- =fx � . A cumulated dirt and grit. Where applicable, test the drain valve using CARB procedure TP-201 . 1 C or TP-201 . 1 D. If the 17a7" drain valve passes testing no further maintenances required . If Ref r } d the drain valve fails testing, remove the valve, soak in waterYY JY and use high-pressure air, if needed, to clean . Reinstall the i - -- drain valve to its proper position and where applicable, test INA the valve with CARB procedure TP-201 . 1 C or TP-201 . 1 D. if �� I problems persist, replace the drain valve with P/N 1 DK-2100- If EVR (specified torque 11 .5 ft- lbs min to 13 .5 ft-lbs max, 5/ 16- - ---� --� 18 UN thread) . The sealable cover 0 SC) adjustment nut is set 1 at the factory, but due to environmental conditions it may be 7 necessary to adjust it to either improve sealing or ease cover Length of Nipple = Dimension A - Dimension B - Dimension C - 2" Min removal . Figure 6 IMPORTANT: Leave these instructions with the Station Operator.