WORK PLANS - Laserfiche WebLink

Home Browse Search

Protective&Marine Coatings PRODUCT DATA SHEET • MACROPDXY° 646 FAST CURE EPDXY nI ' 1i I _ APPLICATION APPLICATION CONDITIONS Temperature: Airless Spray* Tem p Air: 35°F 1.7°C minimum, 120°F 49°C))maximum Pump..............................30:1 Surface': 35°F 1.7°C minimum, 250°F 120°C)maximum Pressure.........................2800-3000 psi(193-206 bar) ° ° Material: 40 F 4.5 C minimum Flose...............................1/4" ID 6.3 mm) ° Tip 017"-.0 3"(0.43-0.58 nim) At least 5°F(2.8'C)above dew point Filter...............................60 mesh o Relative humidity: 85% maximum Reduction.......................As needed up to 10% by volume y Conventional Spray* 'When spraying a surface above 120°F(49°C),reduce material 10%with Gun................................DeVilbiss MBC-510 Reducer#100,R71<100.Spray .apply only. Product will produce an oraDue Fluid Tip.........................E peel appearance when applied at elevated temperatures_.___ A,ir Nozzle.......................704 - - APPROVALS Atomization Pressure.....60-65 psi 4.1-4.5 bar - Fluid Pressure................10-20 psi �0.7-1.4 bar; % uitable for use In USDA inspected facilities Brush* Acceptable for use in Canadian Food Processing facilities, Brush..............................Nylon/Polyester or Natural Brise categories: D1,D2, D3(Confirm acceptance of specific part numbers/rexes with your SW Sales Representative) Roller* • Conforms to AWWA D102 OCS#5 Cover.............................3/8"woven with solvent resists t core • Conforms to MPI#108 • This product meets specific design requirements for non-safety Plural Component Spray..Acceptable related nuclear plant applications in Level II, III and Balance of Plant,and DOE nuclear facilities* *RE duction.........................As needed up to 10%b,t volum Meets Class A requirements for Slip Coefficient,0.36 @ 6 mils/ If specific application equipment is not listed above equival nt 150 microns dit(Mill White only) e:ILipment may be substituted. --- *Nuclear qualifications are-N&,Glicense specific to the facility RECOMMENDED SYSTEMS Diy Film Thickness/ct. Mils- Microns ADDITIONAL NOTES Steel,smooth masonry/concrete, Immersiofl &Atmospheric Tint PartAwith Maxitoners at 150%strength.Five minutes minimum 2 Cts. Macropoxy 646 5.0-10.0 (125-250) mixing on a mechanical shaker is required for complete mixing of Steel, Oroanic Zinc Primer,Atmospheric color. 1 Ct. Zinc Clad IV(85) 3.0-5.0 75-125) Tintin is not recommended for immersion service. 1 Ct. Macropoxy 6 36 5.0-10.0 (125-250) g Steel, Inorganic Zinc Primer,Atmospheric Quik-Kick Epoxy Accelerator is acceptable for use.See data page 1 Ct. Zinc Clad II 85) 2.0-4.050-100)) for details. 1 Ct. hAacropoxy 46 5.0-10.0 (125-25b) Steel,Oroanic Zinc/Epoxy/Urethane Topcoat Acceptable for concrete floors. 1 Ct. Zinc Clad IV(85) 3.0-5.0 �75--125) When spraying a surface above 120'F (49°C), reduce material1 Ct. Macropoxy 3.0- 75250 1 Ct. Acrolon 7300 2.0-4.0 50-100) 10%with Reducer#100.Spray apply only.Productwill produce an orange peel appearance when applied at elevated temperatures. Steel, Inorganic Zinc/Epoxy/Urethane Topcoat 1 Ct. Zinc Clad 11 (85) 2.0-4.0 (50-100) Topcoating:It is recommended to apply a thinned-down,low wet film 1 Ct. Macropoxy 646 3.0-10.0 75-250)) thickness mist coat over zinc rich primers to help avoid outgassing. 1 Ct. Acrolon 7300 2.0-3.0 50-100 Allow it to tack up and seal the surface. Then apply a full wet film Steel,Organic Zinc/Eoxy/Polysiloxane Topcoat,Atmosphenc thickness coat as directed. 1 Ct. z.inc Clad IV�85) 3.0-'i.0 �75-125 Mix contents of each component thoroughly with lows speed ower 1 Ct. Macropoxy 646 3.0-10.0 75-250 p g y p p 1-2 Cts. Sher-Loxane 800 2.0-4.0 50-100 agitation. Make certain no pigment remains on the bottom of the can.Then combine one part by volume of Part A with one part by Concrete/Masonry,Smooth, Immersion &Atmospheric volume of Part B.Thoroughly agitate the mixture with power agita- 2 Cts. Macropoxy 646 5.0-10.0 (125-250) tion.Allow the material to sweat-in as indicated prior to application. Re-stir before using. The systems listed above are representative o`the product's HEALTH AND SAFETY u_e, other systems may be appropriate. --- Refer to the SDS sheet before use. _ WARRANTY Published technical data and instructions are subject to change without notice.Contact your Sherwin-Williams representative for additional technical data and instructions. TI1e Sherwin-Williams Company warrants our products to be free of manufacturing defects in accord with applicable Sherwin-Williams quality control procedures.LiabilityDISCLAIMER for products proven defective,if any,is limited to replacement of the defective product or the refund of the purchase price paid for the defective product as determined by The information and recommendations set forth in this Product Data Sheet are based Sheiwin-Williams. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS upon tests conducted by oron behalf of The Sherwin-Williams Company.Such informa- MADE BY SHERWIN-WILLIAMS, EXPRESSED OR IMPLIED, STATUTORY, BY tion and recommendations set forth herein are subject to change and pertain to the OPERATION OF LAW OR OTHERWISE, INCLUDING MERCHANTABILITY AND product offered at the time of publication.Consult your Sherwin-Williams representative FITNESS FOR A PARTICULAR PURPOSE. to obtain the most recent Product Data Sheet. Ref:1101-1 www.sherwin-williams.com/protective Page 2 of 2