ARCHIVED REPORTS XR0007814 - Laserfiche WebLink

Home Browse Search

TYPICAL SEWAGE INSTALLATION-RECOMMENDED INSTALLATION (1) Eiectncal wrong and protection must be in accordance with National Electrical Code and any other applicable state and local electricat requirements (2) Install proper Zoeller unicheck(combination union and check valve),preferably lust above the basin to allow easy removal of the pump for cleaning or repair On sewage effluent or dewatenng,if high 2 e head or below cover Installation Is required use 30-0152 on i%2"and 2'pipe and 30 0160 on 3"pipe See(6)below 9 (3) All Installations require a basin cover to prevent debris from falling Into the basin and to prevent accidental Injury 4 a (4) Gas tight seals are required in all sewage Installations to contain gases and odors 4 (5) Vent gases and odors to the atmosphere through vent pipe (6) When a Unicheck Is Installed,drill a 3116"dra hole in the discharge pipe even with the top of the pump NOTE THE HOLE MUST ALSO BE BELOW THE BASIN COVER AND CLEANED PERIODICALLY (High Head unit see#3 under'Caution"on front page) Water stream will be visible from this hole • , during pump run periods ruNN (7) Securely tape or clamp power cord to discharge pipe a (8) Locate float switches as shown in sketch to left The best place for the off paint is above the motor • housing and positioned 180°from the inlet Never put'afF point below discharge on pump o e NOTE FOR AUTOMATIC PUMPS,USE DEWATERING INSTALLATION SKETCH BELOW � (9) Use full-size discharge pipe " (10) Basin must be in accordance with applicable codes and spectfications (11) Pump must be level and float mechanism clear of sides of basin before starting pump (12) Basin must be dean and free of debris after installation (13) Gate Valve or Ball Valve to be supplied by installer and mstailed according to any and all codes SK290 NOTE,Alleys refer to Zoeller FMO551 anNor SSPMA Recommended Sewage Pump Insteilatim and Maintenance TYPICAL EFFLUENT INSTALLATION-RECOMMENDED INSTALLATION TOL°w PRESSURESYSTEM (1) Electrical wrong and protection must be in accordance with National Electrical Code and any other MOUND SYSTEM{swaa FILTEp, LEACHING Re.°°n°THER applicable state and local electrical requirements GNO'JNa UNE '2 z ON SMIE DISPOSAL SYSTEM (2) All installations require a basin cover to prevent debris from falling into the basin,and to minimize 1 accidental injury AC 3 MM i (3) Wire pump to power through a Zoeller watertight junction box or watertight splice ax TYPE� NOTE Watertight endosure is a must in damp areas See FM0732 See No 8 on front page (4) Use full-sized discharge pipe 5 (5) Install proper Zoeller umcheck(combination union and check valve) preferably lust above the basin to allow easy removal of the pump for cleaning or repair On sewage effluent or dewatenng,if high head or below cover installation is required use 30.0152 on 1 112"and 2"pipe and 30-0160 on 3' ' pipe See(6)below n (6) When a Unicheck is Installed drilla 3116"d1a hole in the discharge pipe even with the top of the pump ALARM FLOAT The 50 and 90 Series pumps have a built in vent hole NOTE THE HGLE MUSTALSO BE BELOW TURN THE BAS[N COVER AND CLEANED PFR10D1CALLY(High Head unit see#3 under Caution on ON T front page) Water stream will be visible from this hole during pump run periods WIN FILTER TURN ° (7) Securely tape or damp power cord to discharge pipe °FE (8) Refer to SSPMA Effluent Sizing Manual for oeterminlng'on" - ofr switches a (9) Install blocks or bricks under pump to provide a settling basin 9 F9 a O o (10) Basin must be dean and free of debris after Installation (11) Gate Valve or Ball Valve to be supplied by Installer and Installed according to any and all codes (12) Septic tank risers must be used for easy pump and filter access SEPTIC Twat DOSING aHAMeEn SK291 NOTF.Sea FM0531 FM0732&FM1420 fwAiamm rontmis&Junmon Bcxe& TYPICAL DEWATERING INSTALLATION-RECOMMENDED INSTALLATION „ Q (1) Electrical wiring and protection must be In accordance with National Electrical Code and any other applicable state and local electrical requirements (2) Install proper Zoeller unrcheck(combination union and check valve),preferably lust above the basin Z - to allow easy removal of the pump for cleaning or repair On sewage effluent or dewatenng d high head or below cover installation is required use 30-0152 on 1-1#2"and 2"pipe and 30 0160 on 3" pipe See(6)below (3) All Installations require a basin cover to prevent debris from falling Into the basin and to prevent 2 accidental injury (4) Securely tape or damp power cord to discharge pipe clear of the float mechanism (5) Minimum 18"dia x 24"deep basin Larger depths may be required (6) When a Unicheck 1s Installed drilla 3116"dia hole in the discharge pipe even with the top of the pump The 50 and 90 series pumps have a built in vent hole NOTE THE HOLE MUST ALSO BE BELOW 4 THE BASIN COVER AND CLEANED PERIODICALLY(High Head unit see#3 under Caution'on I front page) Water stream will be visible from this hole during pump run periods d (7) Use a full-size discharge pipe 5 ,um (8) Pump must be level and float mechanism clear of sides of basin before starting pump C8 ON (9) Install blocks or bricks under pump to provide a settling basin (10) Basin must be dean and free of debris after Installation 9 NP" (11) Gate Valve or Ball Valve to be supplied by installer and Installed according to any and all codes OFF ,o (12) Gas tight seals are required In all sewage installations to contain gases and odors (13) Vent gases and odors to the atmosphere through vent pipe SK292 NOTE See FMo531 FMO732&FM1420 far Atamm Caritrals&Junadon Boxes All installabons must comply with all applicable electrical and plumbing codes,including, but not limited to,National Electrical Code,local,regional,andfor state plumbing codes,etc Not intended for use in hazardous locations ©Copyright 2003 Zoeller Co AN nghts reserved a