Laserfiche WebLink
'For Red Thread IIA pipe, the hydrostatic cyclic design stress was determined at 1501 and 200°F per ASTM D2992, <br />Procedure A. Based on this data, the extrapolated value at 75°F is 13,073. <br />Bending <br />RED THREAD IIA PIPE <br />PROPERTY <br />psi @ 75°F <br />p <br />MPa @ 24°C <br />° <br />psi @ 150 F <br />MPa @ 66 <br />Axial Tensile (ASTM D2105) <br />Meters <br />15.5 23.2 29.6 43.3 <br />Ultimate Stress <br />10,300 <br />71.0 <br />8,200 <br />56.5 <br />Modulus of Elasticity <br />1.82 x 108 <br />12,548 <br />1.76 x 101 <br />12,135 <br />Axial Compression (ASTM D695) <br />Ultimate Stress <br />33,300 <br />230.0 <br />25,600 <br />176.4 <br />Modulus of Elasticity <br />1.26 x 101 <br />8,687 <br />0.89 x 101 <br />6,159 <br />Beam Bending (SFPTM) <br />Ultimate Stress <br />23,000 <br />159.0 <br />19,111 <br />131.8 <br />Long Term per ASTM D2925 <br />2.18 x 101 <br />15,031 <br />1.19 x 101 <br />8,181 <br />Hydrostatic Burst (ASTM D1599) <br />Ultimate Hoop <br />Tensile Stress <br />34,000 <br />234 <br />39,200 <br />271 <br />Hydrostatic Design (ASTM <br />2"-3" <br />2" -3" <br />2"-3" <br />2"-3" <br />D2992) <br />9,410 <br />64.9 <br />7,400 <br />51 <br />Procedure A <br />4"-6" <br />4"-6" <br />4"-6" <br />4"-6" <br />Cyclic 150 x 101 <br />13,073" <br />90.1 <br />10,500 <br />72.4 <br />Cycles <br />Coefficient of Linear <br />0.88 x 10-5 in/in/°F <br />Thermal Expansion (SFPTM) <br />1.58 x 10-1 mm/mm/°C <br />Specific Gravity <br />1.8 <br />Flow Factor <br />Hazen -Williams Coefficient <br />150 <br />'For Red Thread IIA pipe, the hydrostatic cyclic design stress was determined at 1501 and 200°F per ASTM D2992, <br />Procedure A. Based on this data, the extrapolated value at 75°F is 13,073. <br />Bending <br />Radius, Minimum <br />Nominal <br />2" 3" 4" 6" <br />Pipe Size <br />15/4.57 22-25/6.7-7.62 <br />Feet <br />51 76 97 142 <br />Meters <br />15.5 23.2 29.6 43.3 <br />ASTM D2996 <br />Designation Codes <br />2"-3" RTRP-11AF1-2111 <br />4" RTRP-11AH1-2111 <br />6" RTRP-11AH1-2112 <br />Pipe Lengths Available <br />Size <br />(in) <br />Feet/Meters <br />Standard Random <br />2-6 <br />15/4.57 22-25/6.7-7.62 <br />�7 <br />Testing: <br />NOV 17 2016 <br />Installed pipe systems should be tested prior to use to assure <br />soundness of all joints and connections. Locate pressure gauge ENVIRONMENTAL HEALTH <br />in close proximity to the pressurizing equipment, not directly on <br />the piping system. A pressure gauge with the test pressure at mid- DEPARTMENT <br />scale is recommended. <br />National Oilwell Varco has produced this brochure for general information only, and it <br />is not intended for design purposes. Although every effort has been made to maintain <br />the accuracy and reliability of its contents, National Oilwell Varco in no way assumes <br />responsibility for liability for any loss, damage or injury resulting from the use of information <br />and data herein nor is any warranty expressed or implied. Always cross-reference the <br />bulletin date with the most current version listed at the web site noted in this literature. <br />North America South America &= Asia Pacific Middle East <br />17115 San Pedro Ave. Suite 200 Estrada de Acesso A Zona P.O. Box 6, 4190 CA No. 7A, Tuas Avenue 3 P.O. Box 17324 <br />San Antonio, Texas 78232 USA Industrial Portu3ria de Suape, s/no. Geldermalsen, The Netherlands Jurong, Singapore 639407 Dubai, UAE <br />Phone: 210 477 7500 Recife, PE, Brazil 55.590-000 Phone: 31 345 587 587 Phone: 65 6861 6118 Phone: 971 4881 3566 <br />Phone: 55 31 3501 0023 <br />www.fgspipe.com fgspipe@nov.com <br />MW Fiber Glass Systems <br />©2012 National Oilwell Varco. All rights reserved. <br />FH1200 - September 2012 <br />