INSTALL 2003 - Laserfiche WebLink

Home Browse Search

~ ble Entry Positive Seal Quality Materials Corrosion Resistance sump Entry The exterior studded metal Flexible entry boots have been compression ring that provides tested to withstand a minimum the positive sealing pressure is of 6' of liquid head pressure. encapsulated within rubber to These seals provide a studded protect it from corrosion. More flange connection to create a than a 1/8"of rubber isolates the positive and secure seal where metallic studded ring from the the rubber contacts the sump ground environment. All studs wall and also around the pipe or are made of 401 stainless steel conduit. Tightening down on a and are only exposed on the series of stud fasteners with a inside of the containment sump. compression ring provides a high compression mechanical seal compared to screw on type Chemical Compatibility bulkhead seals. All seals are made of specially formulated Buna-N rubber compound which has been Angled Entries independently tested to insure its Pipe and conduit entering compatibility with a wide the containment sumps may assortment of chemicals. These not be perpendicular with tests include measuring the the sump wall. Angled entries material's retention of properties ` are generally a result of as well as the physical directional plumbing restrictions characteristics of the seal after on the inside of the exposure. containment chamber due to space limitations. Flexible entry UL/ Listed boots are flexible enough to angled pipe or conduit Environ flexible entry boots are Listed with Underwriters permit tries an two axises) into the Laboratories, Inc., (UL). The scope of the tests include broad en si tries ( of a containment compatibility testing for both petroleum products and burial environments as well as physical testing to confirm the entry boots chamber. All flexible entry structural integrity and liquid tightness. boots permit angled entries up to a 15 degree angle off the Sizes Available perpendicular center line in any Application direction without leaking or �. i ��,. > putting undue stress on the pipe �•`� � or conduit seal. i � _ to,wal3l91 ngK 9,,, Designed to seal1.051 3/4'.tigid NcoL:.�«y Universal Alignment 1.32" 3100 Designed to sea{1 rigid conduit. These seals are also capable of �. _. universal pipe alignment either4.25" FEB-3150 Des9 µ ned to seal 1-1/2'standard rigid PIPs. up and down or side to side. Thisfle�obie pipe feature allows accommodation of ,� 1.81" 4.75" FEB-5150 Designed to seal 1-1R"Gwaax 6:25' FEB-6150 Designed to seal1-1/2"GsoAexflexiblepim pipe entry holes which are 1.81" installed slightly off exact center G --7 2,37, 625• FEB-5200 Designed to seal 2"GeoRaKfle)dblepipe. alignment in the chamber wall. Designed to seal 3"standard rigid pipe. This movement will prevent the \ _-� 3.50" 6.25" FEB g chamber wall from putting C 3.50" 6.25" `FEB-6350 Designed to seal 3'rigid ducting. undue stress on the pipe coupling/fitting joint and the 3.90" 7.75" FEB 7390 Designed to seal 3-1/2"custom pipe. entry boot as well. For flexible t f ': 4.50" 7.75" FEB-7400 Designed to seal 4"standard rigid pipe. piping applications within dispenser sumps, the stresses 4.50" 7.75" `FEB-7450 Designed to seal 4"GeoDuctfle>uble ducting. 9 FEB-8600 Designed to seal 6"standard rigid pipe. on the pipe fittings below the 6.50" product inlets are minimized by •ThesenoorsreauireaSun Reaucer0onrnsdaseoaraterv.ornncruaeanavum emauowrorauP'°mirie Msm° the boot's flexibility. ■ Patent claims allowed. ��r�n EP;0090 620 Pennsylvania Drive•Exton,PA 19341 •Tel:(610)321-0200•customer Service 18001 833-1883 a y � < J.,,,r99x,5Mr.G Fax:16101 321.0406•http://www.envproduct.com•U.S.Patent 5263794.527151859199�67 5366318. 5346625,5398976,Other U.S.and Worldwide Patents Pending•m Copyright