Laserfiche WebLink
IN <br />® <br />r� <br />Multi-9yncInstallation Instructions <br />�DPM <br />For Blueline Medium Fittings - - - — <br />MrM.rn <br />jq10)This <br />'PE'= <br />kitovides the Multi <br />pr 9�rncRapairforapplicatiortswherethelHpeisoomingthruthe <br />r.rm� <br />sump wall straight or at an angle. <br />WARNING Prepare all surfacesto be bonded prior to completing installation steps below. <br />Failure to follow each step will void warranty & may result in premature failure of penetration fitting. <br />Page I <br />This Kt apnliesfor repairing Sueline Medium Fittings <br />General Instructions for: Cl.F.ANING dray all surfaces to be bonded with DBCCleaner and allow to air dry or wipe excesswith a dean dry <br />doth. Sirfacesmust bedry before applying bonder. <br />General Instructions for. BONDINGTO POLY SUM PSOR R BE131GLASSSUM RR Clean, sand and rough up sump surfaces. Clean fitting and <br />apply aRTITEor DSII between Bonding fang & sump wall. <br />SUP 1: Felmave Old Boot <br />• Remove damps <br />b'TB'2: dean all Fbpair Components <br />clean all repair components with DBC <br />3: Race & Dry Fit Cuff Rrig,9eeve & Insert <br />- Wrack the split cuff ring over the oldfitting <br />• Cut away old boot <br />prior to installation <br />Wrack the split insert over the pipe <br />• dean & sand fitting <br />flit <br />Wrack the split sleeve over the pipe & up to the <br />= <br />(leaner *lit <br />CLff Seeve <br />bonding ring with the fill port up <br />EooerRrlclrtsert Muttkw <br />Insert Fbducer <br />If everything fits continue with <br />SfEIR5. Install The Seeve, O.rff Fang& Insert <br />STEP 6: Instalf & Bond Eccentric lnsed & Multi -Sync <br />the install. If there isa problem <br />Apply 21p-Titetothe outer surface ofIhe <br />PeduoerBaekTogether <br />with the fit & function of these <br />parts, either adjust to make fit if <br />insert and fully seat inside of cuff <br />• Apply Zp-Tile to the inner surface of the cuff <br />Wrack Eboentric Insert aroundthepipe <br />Wradk Multi -Sync Peducer around thepipe <br />possible, or call the factory (530- <br />ring and slide all the way onto the cuff <br />Position the sleeve with the fill port at the top <br />Apply Zip -Tate to split area on Eccentric Insert, press <br />ends together & damp <br />534-3966) for additional help <br />Oneeyou have the sleeve tined up correctly, <br />1. Apply a bead of Zip-Tite all around the <br />Apply Zp-Tite to split area on Multi -Sync Ibducer, <br />press ends together & damp <br />Sr4: Bond 31eeve,Qjff Fong& Insert <br />• Apply Zip Trte to split cuff ring. Use 1 of <br />outer surface of the cuff ring <br />2. Side sleeve over cuff ring & snap in place <br />thedampsto hold in place while airing. <br />(fill port at top) <br />• Apply 21p-Titeto the split insert and use 1 <br />3. Sat the Clamp the around thesleeve & <br />of the dampstohold inplacewhile <br />wring. <br />over the cuff ring and tightenrtiJ ; <br />_ , .— <br />- J - <br />• Apply ZpTitetothe split sleeveanduse2 <br />damps to hold in place while curing. <br />�, <br />• leave these damps in place for approx 30 <br />minutesfor acing before proceeding to <br />11 <br />the nerd step <br />'4 4fta <br />{ <br />Le <br />qIF <br />