COMPLIANCE INFO 1985 - 2004 - Laserfiche WebLink

Home Browse Search

04/03/2001 07:00 4441735 If you have any questions, please contact your Snaith Fiberglass Products' representative. I?. Bonding surfaces must be dry, so be sure all solvent has evaporated before applying adhesive. 2. Adhesive mixing -Thoroughly mix the adhesive. Complete information and safety precautions are pack- aged with each adhesive kit. When the weather is cool or the ad- hesive has been stored in a cool environment (60'F/16'C or be- low), prewarm the adhesive kits. Do not heat above 807 (27'C)1 See fig. 1.6.6. In some cases, hard- eners may crystal- lize. If this occurs, refer to the instructions provid- ed in each kit. b. Empty all of the contents of the hardener bottle into the can of base adhesive (see Fig. 1.6.7). Mix all of the ad- hesive with all of the hardener. NEVER SPLIT A KR Do not spill hardener during the mixing process. Cut through the adhesive with the edge of the mixing stick to assist In mixing the two components. Mix until the ad- hesive has a uni- form color and a consistent flow off the mixing stick (see Fig. 1.6.8). Wipe down the sides, bottom, and under the rim of the can with the mixing stick to as- sure complete mixture. A. Adhesive working Iffe-Working life or pot life is the (.iine It takes for the adhesive to harden in the mixing RED THREAD 11A Pipe & Flrtings LC SERVICES PAGE 09 a.-TIONId • Installation can. This time is measured b and hardener are first mixed. temperatures above 70'11 (21" the temperature drops below is affected by the quantity of by temperature. Use the folly crease the working life of adt a. Occasionally stir the cation. b. Cut the carton in which the adhe- sive kit is fur- nished so that the height of the car- ton is the same as the adhesive can. Line the inside of the box with rags or paper towels, and wet the rags or towels with sol- vent. Nest the can In prepared carton (see inate the adhesive with the time the adhesive orking life is shorter at tnd becomes longer as F (21'C). Worki!w life red adhesive as x.• 11 as ng methods to in - mixture dut:ing appli- .6.9). Do not contain - Caution: If adhesivebeco s warm and starts to set up in the container, di rd immediately. DO NOT USE THIS ADHESIVE BOND A JOINT! When adhesive is allowed container, the container n 4007 (20S'C). Do not ha out heavy gloves. This ex generate a dense smoke. " tainer outdoors in an ooei 1.6.4 Joint Assembly I. Bell and Spigot joint -THE SI ALIGNED AND LOCKED IN 7 misaligned joint will result in ble joint failure either during a. When the temperature is It warm the bonding surface cleaned and the cleaner ha Evaporation may be slow atures. Use a hot air blow formly to the bell and spilt to the touch (see Pig. 1.6.1 on the Job site (check loci burning propane torch. C touching outside of the be to avoid contact with cleaj hot to the touch, let cool 1 If an electric heating collas place the Joint together dr set up in the mete reach approximately 2 hot containers wit:h- ermic reaction will refore, place the con - ea until it cools. OT MUST BE BELL. A cocked or se lock-up and possi- ting or at a later date. )w 70'F (21'C), pre. ifter the joint has been vaporated). Caur -i. xtremely low ten ,er- nd apply heat u - until warm (not hot) If torches are allowed ides), use a clean - :k temperature by nd inside of the spigot onding surfaces. If are applying adhesive. used to prewarm, hen heat the O.D. of 11