INSTALL 2019 TANK TOP UPGRADE - Laserfiche WebLink

Home Browse Search

' - ITEM #38 Submersible T • •s Franklin Fueling - t Intelligent Submersible Turbine Pump Specifications - Liquid Compatibility . . • • • Max.liquid viscosity: 70 SSU at • F�+4 a*C 60°F (15 'C). •IST models imply alcohol-gasoline A typical turbine model designation has u to five components to define compatibility for fuel mixtures containing p p - diesel fuel with up to 20%biodiesel,100% the pump being supplied as follows: biodiesel,up to 85%ethanol with gasoline, IST XXXXX Y - A - B ' • ' Band 20% MTBE, 20%ETBE or 17% TAME t_ I with gasoline. IST= Basic Model Designation •IST models can also be used with diesel Note: All IST models include fuels,fuel oils, kerosene, Avgas and jet fuels alcohol gasoline compatibility, in a non-gelled pourable state. ' variable speed and variable • All wetted elastomers are made of a high length as part of the base model. grade,fluorocarbon compound. ' A XXXXX=Factory Installed »a Standard Features Options :J- •~ IST model designations may include `= " • All IST models include variable one or more of the following _ speed,variable length options and characters in alphabetical order: alcohol-gasoline compatibility. F = Floatinpsuction adapter 1�/2" NP1 • Check valve:23/4" diameter fluorocarbon female adapter) P seal constructed on cast aluminum body Rc� and steel backing washer, K = Intake filter screen (IFS,factory • Pressure relief valve:available in four installed to PMA) M = MagShell'" (flow enhancing, pressure relief settings,integral to check expanded PMA shell) For full diagram see Ordering Guide. valve.Standard model relieves at 40 psi and resets above 35 psi. R' = Model R check valve (24 psi Power Requirements •Syphon:venturi-type syphon primer relief/22 psi reset for PLLD)W• = Model W check valve 16 si supplied with every submersible. ( P IST models can only be powered by a Syphon check valve and secondary relief/13 psi reset for PPM4000) MagVFC" controller: syphon sold separately. Note:If not otherwise specified,all IST • 2 hp models can operate with single-or • Air eliminator: every submersible includes models are supplied with P 9 P supply tank return path with one-way check valve standard model check valve 40 three-phase incoming ower su I to ( the Ma VFC' psi relief/35 psi reset for MLD, 9 to provide active air elimination. TS-LS300,and TS-LS500). 4 hp models require three-phase incoming • Electrical disconnect:electrical yoke power supply to the MagVFC' for for positive contractor disconnect Y= Pump Motor Horsepower proper operation. during service. Rating— Incoming power supply to the MagVFC" VS4 =4 hp variable speed ' can be 200-250 V A C, 50 or 60 H z. Approvals -Note:If not otherwise specified,2 hp • MagVFC" outputs a three-phase,variable • Consult factory for applicable approvals, variable speed is implied. frequency signal, valid for FE Petro variable speed pumps only. A= Model Length ' Quality Certification •2 hp max. motor draw: 7 Amps. 1 = 2 hp variable length,59"-87" •4 hp max. motor draw: 15 Amps. Franklin Fueling Systems is an ISO 9001 Certified Manufacturer. 2= 2 hp variable length,90%151" • MagVFC- max.line draw:20 Amps. 3 = 2 hp variable length,122"-213" ' UL1 = 4 hp variable length,64"-92" Pump Motor VL2 = 4 hp variable length,95"-156" • 2 hp or 4 hp,variable speed,two-stage (; U� US LISTED VL3 = 4 hp variable length,127"-218" centrifugal type pump motor with integral, Note:IST-2 and ISTVS4-VL2 models fit ' automatic,thermal overload protection. 94%of all known installations. • Max.flow:2 hp = 110 gpm,4 hp = 140 gpm. B= Riser Pipe Length • Max.pressure:selectable operating Riser pipe length is expressed as two ' pressure on MagVFC' between 24 psi and numeric characters that indicate the 42 psi deadhead. total length of the riser in inches. Riser • Available with MagShell",which results in pipes are available from 7"to 69" in 45%increased flow area around motor. 1"increments(additional charge for ' risers 31" or longer). 16 '