Laserfiche WebLink
Technical Data Sheet <br /> PF Series 4" (100 mm <br /> Ca <br /> or.... <br /> Submersible Ef fIuent Pumps 800.34 <br /> 800.348-9843 <br /> Applications Features/Specifications <br /> Our 4"(100 mm)Submersible Effluent Pumps are designed to To specify this pump for your installation,require the following: <br /> transport screened effluent(with low TSS counts)from septic • Minimum 24-hour run-dry capability with no deterioration in <br /> tanks or separate dosing tanks.All our pumps are constructed of pump life or performance* <br /> lightweight,corrosion-resistant stainless steel and engineered . 'A-inch(3-mm)bypass orifice(patent pending)to ensure flow <br /> plastics;all are field-serviceable and repairable with common recirculation for motor cooling and to prevent air bind <br /> tools;and all 60-Hz PF Series models are CSA certified to the U.S. <br /> and Canadian safety standards for effluent pumps,meeting UL Liquid end repair kits available for better long-term cost of <br /> requirements. ownership- TRI-SEALT"^floating impeller design on 10,15,20,and 30 gpm <br /> (0.6, and 1.9 Usec)models;floating stack design on 50 and <br /> 75 g <br /> including pressurized drainfields,packed bed filters,mounds,aer- pm(3.2 and 4.7 Usec)models <br /> obic units,effluent irrigation,effluent sewers,wetlands,lagoons, <br /> and more.These pumps are designed to be used with a Biotube'" • Super stainless Franklin Electric motor,rated for continuous <br /> pump vault or after a secondary treatment system. use and frequent cycling <br /> • Type SOOW 600-V motor cable(suitable for Class I,Division 1 <br /> and Division 2 applications) <br /> • Five-year warranty on pump or retrofit liquid end from date of <br /> — Discharge manufacture against defects in materials or workmanship <br /> connection *Not applicable for 5-hp(373 kW)models <br /> Standard Models <br /> — Bypass See specifications chart,pages 2-3,for a list of standard pumps. <br /> orifice For a complete list of available pumps,call Orenco. <br /> Y Nomenclature <br /> PF 30 05 1 1 -❑ <br /> I Cord length,ft(m): <br /> Blank = 10(3) 20' = 20(6) <br /> — Suction 30 = 30(9) 50 = 50(15) <br /> connection <br /> Voltage,nameplate: <br /> 1 = 1152 200 = 200 <br /> 0 2 = 230' 4 = 460 <br /> 0 <br /> E Frequency: <br /> c N 1 = single-phase 60 Hz 3 = three-phase 60 Hz <br /> 0 5 = single-phase 50 Hz <br /> � c <br /> u Horsepower(kq: <br /> 03 = 'h hp(0.25) 05 = %2 hp(0.37) <br /> Q 07 =3/hp(0.56) 10 = 1 hp(0.75) <br /> 15 = 1-%2 hp(1.11) 20 = 2 hp(1.50) <br /> 30 = 3 hp(2.24) 50 = 5 hp(3.73) <br /> Nominal flow,gpm(Use c): <br /> 10 = 10(0.6) 15= 15(1.0) <br /> 20 = 20(1.3) 30 = 30(1.9) <br /> t1 <br /> Powered by 50 = 50(3.2) 75 = 75(4.7) <br /> Ca. —`R� Franklin Electric Pump(PF Series) <br /> cus <br /> LR80980 'Note:20-foot cords are available only for single-phase pumps through 1-%z hp <br /> 21/2-hp(0.37k%only <br /> LR2053896 1220 volts for 50 Hz pumps <br /> ©2012 Orenco SystemO Inc. NTD-PU-PF-1 <br /> Rev.2.0,©01/12 <br /> Page 1 of 6 <br />