INSTALL_2009 - Laserfiche WebLink

Home Browse Search

� 1 Intelligent Submersible Turbine Pump Specifications Liquid Compatibility • . • . - • Max. liquid viscosity: 70 SSU at • 60°F(15 •C). •IST models imply alcohol-gasoline A typical turbine model designation compatibility for fuel mixtures containing has up to five components to define up to 100%ethanol or methanol,and the purnp being supplied as follows: 20%MTBE, 20% ETBE or 17%TAME IST XXXXX Y- A - B B with gasoline. Designation •IST models can also be used with diesel IST= Basic Model Desi g fuels,fuel oils,kerosene,Avgas and jet fuels Note:All IST models include in a non-gelled pourable state. the options of alcohol-gasoline •All wetted elastomers are made of a high compatibility,variable speed and grade,fluorocarbon Viton'compound. variable length as part of the base model. A Standard Features XXXXX = Factory Installed •All IST models include variable Options speed,variable length options and IST model designations may include _ alcohol-gasoline compatibility. one or more of the following 0 •Check valve:2-3/4"diameter fluorocarbon characters in alphabetical order: Vitonv seal constructed on cast aluminum F=Floating suction adapter body and steel backing washer. (I-1/2"NPT female adapter) WW • Pressure relief valve:available in four K=Intake filter screen (IFS,factory pressure relief settings, integral to check installed to PMA) valve.Standard model relieves at 40 psi and M = MagShell- (flow enhancing, For full diagram see page S. resets above 35 psi. expanded PMA shell) •Syphon:venturi-type syphon primer R`=Model R check valve Power Requirements supplied with every submersible.Syphon (24 psi relief/22 psi reset for PLLD) check valve and secondary syphon sold IST models can only be powered by a separately. W' Model W check valve(16 psi MagVFC-controller. relief/13 psi reset for PPM4000) •Air eliminator:every submersible includes 'Note: If not otherwise specified,all IST •2 hp models can operate with single-or tank return path with one-way check valve p three-phase incoming power supply to to provide active air elimination. models are supplied with the MagVFC". standard model check valve •Electrical disconnect: electrical yoke (40 psi relief/3S psi reset for •4 hp models require three-phase incoming for positive contractor disconnect MLD and TS-LS300). power supply to the MagVFC'for during service. proper operation. Y= Pump Motor Horsepower •Incoming power supply to the MagVFC- Approvals Rating" can be 200-250 VAC, 50 or 60 Hz. VS4=4 hp variable speed • Consult factory for applicable approvals. •MagVFC-outputs a three-phase,variable "Note: If not otherwise specified, frequency signal,valid for FE Petro variable 2 hp variable speed is implied. speed pumps only. Quality Certification •2 hp max.motor draw:9 Amps. • Franklin Fueling Systems is an ISO 9001 A= Model Length •4 hp max.motor draw: IS Amps. Certified Manufacturer. I =2 hp variable length,59"-87" • MagVFC-max.line draw: 20 Amps. `Niton")is a registered trademark of DuPont 2 =2 hp variable length, 90"-151" Dow Elastomers. 3 =2 hp variable length, 122"-213" Pump Motor VLI =4 hp variable length, 64"-92" •2 hp or 4 hp,variable speed,two-stage VL2=4 hp variable length,95"-156" (, �L US LISTED centrifugal type pump motor with integral, VL3=4 hp variable length, 127'-218" automatic,thermal overload protection. Note: IST-2 and ISTVS4-VL2 models fit •Max.flow:2 hp= 110 gpm,4 hp= 140 gpm. 94%of all known installations. •Max.pressure:selectable operating B= Riser Pipe Length pressure on MagVFC-between 24 psi and Riser pipe length is expressed as two 42 psi deadhead. numeric characters that indicate the •Available with MagShell-,which results in total length of the riser in inches.Riser 45%increased flow area around motor. pipes are available from 7"to 69"in I"increments (additional charge for risers 31 or longer). 10