|
CLIENT:
<br /> to --� GENERAL NOTES
<br /> PIPING LEGEND w 2" INSIDE 3" DOUBLE WALL FIBERGLASS PRODUCT PIPING
<br /> 2" INSIDE 3" OR 3" INSIDE 4" DOUBLE WALL FIBERGLASS VAPOR RECOVERY PIPING
<br /> - - - - - - - - -
<br /> 2" INSIDE 3" DOUBLE WALL FIBERGLASS VENT PIPING 11N pr
<br /> z TANK AND PIPING INSTALLATION NOTES
<br /> PIPING LENGTHS 1 INSTALL ON�(1) OK REGULAR UNLEADED, ONE (1) 10K/12K PREMIUM UNLEADED/DIESEL DUAL COMPARTMENT "XERXES" DOUBLE WALL FIBERGLASS
<br /> HYDROSTATIC ANNULAR SPACES BY "VEEDER ROOT" TLS-3508 TANK AND PIPING MONITOR AND ALARMARC0
<br /> VAPOR LINE 320' 3 YSTEM. ALSUMPS SHALL BE DOUBLE WALL FROM COLLAR TO THE BOTTOM OF TANK SLAB. SUMPS SHALL BE INDIVIDUALLY CONTINUOUSLY
<br /> 91 PROD LINE 300' MONITORED BY "VEEDER ROOT" MINI HYDROSTATIC SENSORS AND STANDARD LIQUID SENSORS TIED INTO THE TLS-35OR TANK & PIPING MONITOR AND
<br /> 87 PROD LINE 312' ALARM SYSTEM PER LG-162-1 REQUIREMENTS. TANKS TO BE SET MIN. 50" BELOW FINISH GRADE. SEE DWG. M.5.3.04 FOR ADDITIONAL INFORMATION. BP WEST COAST PRODUCTS,LLC
<br /> _ TANK INSTALLATION SHALL BE IN ACCORDANCE WITH MANUFACTURER'S INSTALLATION INSTRUCTIONS.
<br /> -II - - - -- - - - - - - - - - -- - - DIESEL PROD LINE 279'
<br /> - - T -�_ - -- - - - - � - �. - .-� - - - -- -. -- - - -- - -- - - -
<br /> COLONY � ---- --- - - -- 91 VENT LINE 76'
<br /> 2 INSTALL A 7" MIN. REINFORCED CONCRETE SLAB OVER TANKS. SURFACE WATER SHALL BE DIVERTED AWAY FROM EACH MANHOLE BY FORMING A
<br /> 87 VENT LINE 58' CONCRETE CROWN WITH A 1-1/2" DROP IN 18" FROM THE EDGE OF THE MANHOLE RING TO THE SURROUNDING SLAB ELEVATION. TANK SLAB SHALL BE
<br /> ACCESSEABEMENT DIESEL VENT LINE 71' THICKENED AT TANK SUMPS TO BE JUST BELOW TOP OF TANK SUMP'S SECONDARY CONTAINMENT TERMINATION PER AB-2481 REQUIREMENTS. CONSTRUCT
<br /> SLAB PER CIVIL SLAB INSTALLATION DETAILS AND SPECIAL REQUIREMENTS SHOWN ON DETAILS.
<br /> INSTALL FOUR (4) 4" EVR PHASE I APPROVED DUAL POINT FILL ADAPTERS AND CAPS. INSTALL STRAIGHT ALUMINUM DROP TUBES. (GAS & DIESEL)
<br /> ❑ Q INSTALL THREE (3) 4" EVR PHASE I APPROVED DUAL POINT STAGE I VAPOR RECOVERY ADAPTERS AND CAPS. (GAS ONLY)
<br /> INSTALL ONE (1) 2 HP VARIABLE SPEED TURBINE IN THE 20,000 GALLON REGULAR UNLEADED TANK (TANK #1).
<br /> - INSTALL ONE (1) 2 HP VARIABLE SPEED TURBINE IN THE 10,000 GALLON DIESEL TANK COMPARTMENT #2.
<br /> INSTALL ONE (1) 2 HP VARIABLE SPEED TURBINE IN THE 12,000 GALLON PREMIUM TANK COMPARTMENT (TANK #3).
<br /> C TURBINE SYSTEMS TO BE EQUIPPED WITH 3 GPH ELECTRONIC LINE LEAK DETECTION. LEAK DETECTORS ARE TO BE TESTED FOR THE 3 GPH LEAK
<br /> DETECTION PRIOR TO START UP. CONTRACTOR TO PROVIDE TEST DATA AT THE TIME OF PUNCH LIST AS WELL AS INCLUDE IN CLOSE OUT BINDER. SET
<br /> PROPERTY UNE MM € TURBINE INTAKES AT 5" FROM BOTTOM OF TANKS. TURBINES TO BE EQUIPPED WITH INTAKE FILTER SCREENS. CONTRACTOR IS TO LABEL TURBINES AND
<br /> CONTROLLERS AS TO WHICH PRODUCT THEY SERVE, GREEN CONTROLLER LIGHTS ARE TO GO OUT WHEN TURBINES ARE OFF OR LOSE POWER.
<br /> Ar5C13C COM
<br /> ' © INSTALL 3" INSIDE 4" DOUBLE WALL FIBERGLASS STAGE II VAPOR RECOVERY HEADER FOR "HEALY VAC ASSIST" ORVR/PHASE II EVR COMPATIBLE VAPOR
<br /> 2 wtFIAu a rrm ( RECOVERY SYSTEM. SLOPE 1/8" PER FOOT MINIMUM TO TANKS. LAYOUT TANKS & STAGE II VAPOR RECOVERY PIPING SUCH THAT THE STAGE II PIPING 0
<br /> mAND 1CKIIOVkEOCE BYL'E DRAINS & ENTERS INTO REGULAR UNLEADED TANK FIRST W/ 3" CONNECTIONS, AND CONTINUES 3" TO OTHER TANKS. Z
<br /> 2 I° INSTALL 3" TO 2" REDUCING TEES WHERE HEADERS BRANCH TO DISPENSERS. CONTRACTOR TO INSTALL TRACER WIRE WITH VAPOR PIPING. TESTING OF z
<br /> 3 4 I3WO BVLIARO' PER CITY IW. VAPOR LINES SHALL BE PERFORMED PRIOR TO BACKFILL, PRIOR TO PAVING AND BEFORE STATION OPERATION. THE VAPOR LINE'S INTERSTITIAL SPACE
<br /> BOUAM Ta If PL/DED{ FEET SHALL BE CONTINUOUSLY VACUUM MONITORED PER LG-162-1 REQUIREMENTS. THE CONNECTION FOR THE VACUUM MONITORING SHALL BE LOCATED IN w
<br /> Duk Has HWM EDW OF 1315PESISER Cm.a) 6 7 19 ^aRICL€ nLYT� PE)1 SIDE F
<br /> BDE 3+1 M F 340MR THE 20,000 GALLON TANK FILL SUMP AND THE VACUUM TUBING LOOPED BACK TO THE TURBINE SUMP WHERE THE VACUUM SENSOR IS LOCATED. 0.
<br /> I \ 17 17 Lu
<br /> FH Lam" /0 (a) INSTALL (3) 2" INSIDE 3" DOUBLE WALL FIBERGLASS GASOLINE & DIESEL SUPPLY LINES TO DISPENSERS. PIPING SHALL BE INSTALLED PER 0
<br /> 4fT - MANUFACTURER'S SPECIFICATIONS AND INSTRUCTIONS. PIPING SHALL BE INSTALLED WITH A SLOPE OF 1/8" PER FOOT FROM THE FURTHEST
<br /> N f - - = i REG- - DISPENSER SUMP DOWN TO THE TURBINE SUMPS. CONTRACTOR TO INSTALL TRACER WIRE WITH PRODUCT PIPING. TESTING OF PRODUCT LINES
<br /> �10 \ SHALL BE PERFORMED PRIOR TO BACKFILL, PRIOR TO PAVING AND BEFORE STATION OPERATION. PRODUCT LINES INTERSTITIAL SPACES SHALL 0
<br /> Z
<br /> + I! r
<br /> r BE CONTINUOUSLY VACUUM MONITORED PER LG-162-1 REQUIREMENTS AND TIED INTO THE "VEEDER-ROOT" TLS-350 PLUS CONSOLE. SEE (�
<br /> 1 1 �lts DETAILS FOR CONNECTION LOCATIONS AND VACUUM ZONING DATA.
<br /> +I ® INSTALL "VEEDER ROOT" TANK AND LINE ALARM CONTROL PANEL MODEL # TLS-350 PLUS IN BUILDING AT NORMALLY OCCUPIED LOCATION IN z
<br /> II ) I �I BUILDING. SEE ARCHITECTURAL AND ELECTRICAL DRAWINGS FOR EXACT LOCATION. 0
<br /> 12 II I I I I II O
<br /> I � Q9 INSTALL THREE (3) 2" INSIDE 3" DOUBLE WALL FRP VENT LINES. SLOPE 1/4" PER FOOT (1/8" PER FOOT MINIMUM) TO TANKS AS SHOWN. CONTRACTOR W > N o
<br /> TO INSTALL TRACER WIRE WITH VENT PIPING. THE INTERSTITIAL SPACE OF EACH OF THE VENT LINES SHALL BE CONTINUOUSLY MONITORED VIA A VACUUM m o o rn
<br /> 33 ® BUULMMG EM 9OMbkom H SENSOR TIED INTO THE "VEEDER-ROOT" TLS-350 PLUS CONSOLE PER LG-162-1 REQUIREMENTS. THE DOUBLE WALL VENT PIPING SHALL BE TERMINATED r v
<br /> IN A DOUBLE WALL VENT TERMINATION SUMP THAT WILL BE HYDROSTATICALLY MONITORED AND WILL ALSO HAVE A LIQUID SENSOR INSTALL PER
<br /> PLNP 3H j1 I] LG-162--1 REQUIREMENTS. V p L)
<br /> �I FIX�RIIDOF �� I, I ( 10 TERMINATION POINT OF TANK VENTS TO BE A MINIMUM OF 12' ABOVE GRADE AND NOT WITHIN 5' FROM ANY BUILDING OPENING OR PROPERTY LINE 0 00
<br /> J r• Y m ro
<br /> �I THAT CAN BE BUILT UPON. VENT RISERS SHALL BE INSTALLED IN ACCORDANCE WITH UNIFORM FIRE CODE REQUIREMENTS. INSTALL TWO (2) SPARE Q C� M Q
<br /> a III L ALlw
<br /> 0-9 *...Q �� I ( 1" CONDUITS W/ PULL ROPE FROM GASOLINE VENT RISER TO BUILDING FOR FUTURE TANK DIAGNOSTIC REQUIREMENTS. INSTALL HEALY CLEAN AIR Z W m 6
<br /> I AM 20 1 Z SEPARATOR AND ASSOCIATED PIPING AND FITTINGS PER NEW CARE EVR PHASE II STANDARDS AND E.O. INSTALLATION SHALL BE PER CARB E-0 0 ~ o X
<br /> II nr�w 1 AND MANUFACTURERS INSTRUCTIONS. SEE DETAILS ON SHEET G.0.6.2 M m a Lco
<br /> D MV43E � 11 INSTALL THREE (3) RIGID CONDUITS FOR SUBMERSIBLE PUMP POWER. (ONE FOR EACH TURBINE). NOTE THAT THE LAST 2 FEET OF ALL CONDUIT
<br /> 10 1
<br /> ENTERING TURBINE, FILL, DISPENSER OR VENT TRANSITION SUMPS SHALL BE PVC COATED RIGID CONDUIT. NO. DATE REVISION DESCRIPTION
<br /> + 10 EW HEALY CLEAN AX\\ ( 12 INSTALL TWO (2) DUAL FLOAT TANK ANNULAR SPACE HYDROSTATIC MONITORING SENSORS.
<br /> AIR SEPARATOR DUAL.HIM PER 13 INSTALL BALL FLOAT/VALVE EXTRACTOR ASSEMBLIES FOR VENT, STAGE I AND STAGE II VAPOR RECOVERY AT FILL SIDE SUMP.
<br /> wsraLL ED WATHE'PF QJWWRIFF SIDE 3+1 MPD I
<br /> j� sTnTCH AND 1II�ATHETT PRaOF aV1ur
<br /> PER nK SNR IN9110 WO FM OF� 17 14 INSTALL .1 GPH MAG PROBE TANK LEVEL GAUGES AT LOCATIONS SHOWN
<br /> 110 MAIR!WATER UNHT DBS oeim i 15 TANKS SHALL BE PROPERLY MARKED AND TAGGED WITH STANDARD API IDENTIFICATION MARKINGS AND BRASS TAGS AT FILL MANHOLES.
<br /> . - VAC 11M ® Luf 1fi NOT USED
<br /> + 4 z
<br /> c
<br /> ( 17 INSTALL (6) WAYNE OVATION SERIES (3+0) SINGLE HOSE PER SIDE & (2) WAYNE OVATION SERIES (3+1) DUAL HOSE PER SIDE MULTI-PRODUCT
<br /> DISPENSERS AS SHOWN. DISPENSERS TO BE FITTED WITH "VST" VAPOR BALANCE STAGE fl HOSES, NOZZLES AND BREAKAWAY VALVES PER NEW GARB
<br /> IJ EVR AND ISO PHASE 11 EXECUTIVE ORDER VR-204 REQUIREMENTS. DISPENSERS SHALL BE EQUIPPED FROM MANUFACTURER WITH VEEDER-ROOT ISD
<br /> u! FLOW METERS. CONTRACTOR IS RESPONSIBLE FOR INSTALLING HOSES, NOZZLES AND BREAKAWAYS. INSTALL UNDER DISPENSER CONTAINMENT
<br /> Q Q
<br /> O INCLUDING PRODUCT AND VAPOR SHEAR VALVES AND MONITORING SENSORS. DISPENSER SUMPS SHALL BE DOUBLE WALL TO AT LEAST THE BOTTOM
<br /> - ___ - 1 OF CONCRETE DRIVE SLAB AND HYDROSTATICALLY MONITORRED PER LG-162-1 COMPLIANCE OPTION. THE LAST 2 FEET OF ALL CONDUITS ENTERING
<br /> ■' • �. `�"� *� THE DISPENSER SUMPS SHALL BE PVC COATED RIGID. FOR TYPICAL INSTALLATION DETAILS. START UP BY MANUFACTURER REPRESENTATIVE, GENERAL
<br /> CONTRACTOR TO PURGE LINES WITH A MINIMUM OF 200 GALLONS THROUGH EACH HOSE/NOZZLE. ANY AIR POCKETS OR START UP PROBLEMS DUE TO
<br /> IMPROPER INSTALLATION OR INCORRECT WIRING THAT DESTROYS ELECTRONICS WILL BE BILLED BACK TO THE CONTRACTOR. AFTER PURGING THE
<br /> yam Boor CAum
<br /> PRODUCT LINES OF AIR AND BEFORE VAPOR RECOVERY TESTING, CONTRACTOR IS TO REPLACE THE FACTORY INSTALLED GASOLINE FILTERS WITH NEW
<br /> MDyTDR�
<br /> 8
<br /> EMESaDYP silt-OT
<br /> SEAL:
<br /> yrLl
<br /> gyp mi(moom 18 NOT USED
<br /> I a oumw I �s E D A CH
<br /> + • I + 1g ALL NEW PIPING AND TANKS TO BE INSTALLED PER MANUFACTURERS RECOMMENDATIONS AND INSTALLATION INSTRUCTIONS. CONTRACTOR SHALL USE �,
<br /> +
<br /> FLEXIBLE CONNECTORS FROM THE TANK SUMP TO THE VAPOR RECOVERY MANIFOLD AND MAIN PRODUCT LINES OR SHALL PROVIDE AT LEAST 4 FEET OF 6
<br /> I STRAIGHT FRP PIPE RUN BEFORE A CHANGE OF DIRECTION OF MORE THAN 30 DEGREES. n
<br /> v
<br /> SAY -5
<br /> / i O INSTALL OVERFILL ALARM & ACKNOWLEDGMENT SWITCH, ESO AND MAINTENANCE RECEPTACLE IN LOCATION SHOWN. ALARM AND SWITCH TO BE LOCATED
<br /> A ' 2Q TO PROVIDE AN UNOBSTRUCTED VIEW TO TRUCK DRIVER, PROVIDE BOLLARD PROTECTION OF FREE STANDING POLE. SEE WIRING DIAGRAM ON SHEET 9
<br /> 4
<br /> 21 FINIAL FACILITY EQUIPMENT LOCATIONS TO BE APPROVED BY BP WEST COAST DISTRIBUTION PRIOR TO SUBMITTAL FOR PERMITS TO ENSURE CLEAR AND
<br /> SAFE ACCESS TO THE UNDERGROUND TANKS FOR UNLOADING OPERATIONS.
<br /> f 22 N T UUSED TF OF L�F�
<br /> CONFIDENTIAL�Y
<br /> COMPLIANCE NOTES THE RECIPIENT OF MATERIA UNDERSTANDS THAT
<br /> -- COPYRIGHT IN THE MA WNED BY GLOBAL
<br /> R- ALLIANCE, AND ALSO, THAT THE MATERIALS CONTAIN
<br /> PRrvILEDGED AND CONFIDENTIAL BUSINESS INFORMATION OF
<br /> 1. ARCHITECTURAL AND CIVIL DRAWINGS SHALL TAKE PRECEDENCE FOR REFERENCING ALL DIMENSIONS, PROPERTY LINES,
<br /> GLOBAL
<br /> T}iEwSENCE. ACCORDINGLY,
<br /> THE
<br /> RECENCETA AGREES TO
<br /> AGREES NOT TO DISCLOSE THESE MATERIALS TO ANY OTHER
<br /> ELEVATIONS AND EQUIPMENT LOCATIONS PARTY AND FURTHER AGREES NOT TO MAKE COPIES OF THE
<br /> 2, ALL. DIMENSIONS AND CONDITIONS SHALL BE CHECKED AND VERIFIED IN THE FIELD BEFORE STARTING ANY WORK. ANY MATERIALS. THE RECIPIENT AGREES TO USE THE
<br /> MATERIALS ONLY FOR THE LNIITEO PURPOSE FOR WHICH
<br /> DISCREPANCY SHALL BE CALLED TO THE ATTENTION OF THE OWNERS ENGINEER FOR HIS DECISION BEFORE PROCEEDING WITH GLOBAL ALLIANCE HAS MADE THE MATERIALS AVAILABLE,
<br /> AND RECIPIENT AGREES TO RETURN ALL MATERIALS TO
<br /> THE WORK. GLOBAL ALLIANCE EITHER UPON COMPLETION OF THE
<br /> INTENDED PURPOSE OR UPON THE REQUEST OF GLOBAL
<br /> 3• GENERAL CONTRACTOR SHALL OBTAIN NECESSARY PERMIT FROM APPLICABLE AGENCIES FOR EXCAVATIONS OF TRENCHES 5'-0" AIJANCE WHICHEVER COMES FIRST.
<br /> OR MORE IN DEPTH INTO WHICH A PERSON IS REQUIRED TO DESCEND.
<br /> 4. AN UNAUTHORIZED RELEASE RESPONSE PLAN MUST BE SUBMITTED AND APPROVED BY GOVERNING AGENCY PRIOR TO TANK DEVELOPMENT INFORMATION:
<br /> OPERATIONS.
<br /> -� 5. ALL. MATERIALS SHALL BE COMPATIBLE WITH USE FOR THE INTENDED PURPOSE AS PER NATIONALLY RECOGNIZED CODES, LOCAL UNDERGR. STORAGE
<br /> CODES AND GOVERNING AUTHORITIES.
<br /> 6. THE UNDERGROUND STORAGE TANK SYSTEM SHALL BE COMPATIBLE WITH THE PRODUCT STORED. TANK STANDARDS
<br /> 7. ALL. MONITORING DEVICES SHALL BE INSTALLED PER MANUFACTURER'S SPECIFICATIONS. ELEMENT TPO1
<br /> �f
<br /> 8. GEMERAL CONTRACTOR IS REQUIRED TO PROVIDE 72 HOUR (TYPICAL) NOTIFICATION TO GOVERNING AGENCY PRIOR TO TANK Y 9.0 2010 SERIES
<br /> INSTALLATION. CALIFORNIA MARKET
<br /> 9. TANK AND PIPING SYSTEM TO BE INSPECTED BY OWNER'S THIRD PARTY INSPECTOR & GOVERNING AGENCY AT FOUR (4)
<br /> SEPARA 1
<br /> A. ANK AI�TEST�AFRSETTING IN HOL AND SOAP TEST. 3Q SITE ADDRESS:
<br /> B. TICALLY TESTED FOR 60 MINUTES.
<br /> C. INSPECTION OF ALL SECONDARY CONTAINMENT, INCLUDING TESTING, IN ACCORDANCE WITH COLONY RD
<br /> CAUTION: MANUFACTURER'S GUIDELINES.
<br /> POTENTIAL UTILITY CONFLICT. CONTRACTOR SHALL FIELD VERIFY ALL EXISTING AND D. FINAL INSPECTION INCLUDING ALL PORTIONS OF THE LEAK DETECTION SYSTEM. @a BRADY LN
<br /> NEW UTILITIES PRIOR TO CONSTRUCTION. SEE UTILITY CONFLICT NOTE THE 10. ALL TANK SUMPS AND UNDER DISPENSER CONTAINMENT SUMPS SHALL BE HYDROSTATICALLY TESTED (LAKE TEST) WITH RIPON,CA
<br /> EXISTING WATER, STORM, AND SANITARY SEWER SERVICE SHOWN IS APPROXIMATE, STANDING WATER TO TOP OF REDUCING COLLAR FOR A PERIOD OF 24 HOURS TO INSURE THAT THE SUMPS ARE WATERTIGHT.
<br /> BASED ON FIELD SURVEYS AND "AS-BUILT" RECORDS. THE GENERAL CONTRACTOR RECORD THE TEST RESULTS AND SUBMIT TO OWNER.
<br /> SHALL "POTHOLE" THE EXISTING UTILITIES TO VERIFY THE DIAMETER AND LOCATION 11. TANK SYSTEM, LEAK DETECTORS AND MONITORING SYSTEM INTEGRITY TESTS FORWARDED AND APPROVED BY GOVERNING 95366
<br /> (INCL. ELEVATIONS) PRIOR TO CONSTRUCTION, ANY DISCREPANCIES IN THE AGENCY PRIOR TO TANK SYSTEM BEING PLACED IN OPERATION.
<br /> LOCATION THE EXISTING PIPE OR INCOMPATIBILITY OF THE DESIGN SHALL BE
<br /> BROUGHT TO THE IMMEDIATE ATTENTION OF THE OWNERS REPRESENTATIVE, AND 12. PRIOR TO FUEL BEING PUMPED, STATION MUST HAVE VEEDER ROOT FUNCTIONAL AND MONITORING ANNULAR SPACES OF TANK DESIGNED BY: AGC ALLIANCE Z&OM:
<br /> TO
<br /> OWNERS CIVIL ENGINEER.
<br /> AND DISPENSER SUMPS.
<br /> 13. PAYMENT OF ALL APPLICABLE UST OPERATING FEES SHALL BE SUBMITTED TO THE GOVERNING JURISDICTION CHECKED BY: AGC BP REPM:
<br /> UTILITY CONFLICT NOTE: WITHIN 30 DAYS OF THE FINAL INSPECTION. DRAWN BY: AGC ALLIANCE PM:
<br /> CALMON; 14. EVIDENCE OF FINANCIAL RESPONSIBILITY SHALL BE SUBMITTED TO GOVERNING AGENCY (BY BP). VERSION: PROJECT NO:
<br /> THE CONTRACTOR SHALL BE RESPONSIBLE FOR VERIFYING THE LOCATION, 15, MEASUREMENTS OF BRINE LEVELS SHALL BE TAKEN BY BP REPRESENTATIVE DURING THREE SEPARATE VISITS TO SITE AND 8.15.10
<br /> DIMENSION, AND DEPTH OF ALL EXISTING UTILITIES WHETHER SHOWN ON PRIOR TO FUELING OPERATIONS, REFER TO TANK MANUFACTURER'S INSTALLATION INSTRUCTIONS FOR REQUIREMENTS.
<br /> THESE PLANS OR NOT BY POT HOLING THE UTILITIES AND SURVEYING THE
<br /> HORIZONTAL AND VERTICAL LOCATION PRIOR TO CONSTRUCTION. THIS SHALL TANK EXCAVATION NOTE: 16• TANK TEST METHOD: BEFORE THE UNDERGROUND STORAGE TANK 15 PLACED INTO USE, THE UNDERGROUND STORAGE TANK DRAWING TITLE:
<br /> INCLUDE CALLING UTILITY LOCATE ® 1 (800) 227-2600 AND THEN POT SHALL BE TESTED AFTER INSTALLATION USING ONE OF THE FOLLOWING METHODS TO DEMONSTRATE THAT THE TANK SYSTEM IS UNDERGROUND TANK AND PIPING
<br /> TANK EXCAVATIONS SHALL BE PER OSHA REQUIREMENTS AND BE PERFORMED
<br /> HOLING ALL OF THE EXISTING UTILITIES AT LOCATIONS OF NEW UTILITY PRODUCT TIGHT:
<br /> CROSSINGS TO PHYSICALLY VERIFY WHETHER OR NOT CONFLICTS EXIST. 1) (ENHANCED LEAK DETECTION ELD TEST (IOTA) BY CGRS OR LICENSED AFFILIATE. SITE PLAN
<br /> LOCATIONS OF SAID UTILITIES AS SHOWN ON THESE PLANS ARE BASED FOLLOWING THE RECOMMENDATIONS OF THE SOILS REPORT. TANKS 2) AN INERT GAS PRESSURE TEST THAT HAS BEEN CERTIFIED BY A THIRD PARTY AND APPROVED BY THE BOARD
<br /> EXCAVATIONS THAT REQUIRE SHORING SHALL BE ENGINEERED AND PERMITTED AND INSTALLATION NOTES
<br /> UPON THE UNVERIFIED PUBLIC INFORMATION AND ARE SUBJECT TO SEPARATELY AND SHALL BE THE RESPONSIBILITY OF THE INSTALLING 3) A TEST METHOD DEEMED EQUIVALENT TO ENHANCED LEAK DETECTION OR AN INERT GAS PRESSURE TEST BY THE BOARD IN
<br /> VARIATION. IF CONFLICTS SHOULD OCCUR, THE CONTRACTOR SHALL REGULATIONS ADOPTED PURSUANT TO THE APPLICABLE CHAPTER IN THE CODE. AN UNDERGROUND STORAGE TANK INSTALLED
<br /> CONTRACTOR. HIGH WATER TABLE 15 ANTICIPATED. CONTRACTOR TO SHORE
<br /> CONSULT THE OWNERS CIVIL ENGINEER TO RESOLVE ALL PROBLEMS PRIOR AND DEWATER TANK HOLE EXCAVATION. FOLLOW TANK MANUFACTURER'S 0 10 20 4p Call Tall Free AND TESTED IN ACCORDANCE WITH THIS SECTION IS EXEMPT FROM THE REQUIREMENTS OF CALIFORNIA HEALTH AND SAFETY
<br /> TO PROCEEDING WITH CONSTRUCTION. INSTALLATION INSTRUCTIONS FOR WET HOLE TANK INSTALLATION. 1 (800) 227-2600 CODE SECTION 25292.5.
<br /> SHEET N0:
<br /> TWO 17. REFERENCED CODES SHALL INCLUDE 2007 CBC; 2007 CFC, 2007 CEC; 2007 CMC.
<br /> WORKING DAYS
<br /> BEFORE YOU 18. FIRE SAFETY DURING CONSTRUCTION SHALL FOLLOW 2007 CFC, FIRE EXTINGUISHERS SHALL BE PROVIDED. THE AUTOMATIC FIRE
<br /> 17F=20DIG SPRINKLER SYSTEM IS TO REMAIN IN SERVICE AT ALL TIMES. UNDER NO CIRCUMSTANCE SHALL THE FIRE SPRINKLER SYSTEM BE
<br /> UNDERGROUND TANK AND PIPING
<br /> SITE PLAN LEFT OUT OF SERVICE OVERNIGHT.
<br />
|