COMPLIANCE INFO_1996 - 2004 - Laserfiche WebLink

Home Browse Search

Site Preparatioi d Installation InstructionsT TL_ ,50 UST Monitoring System • Printer Interface Module.Required for interface This section does not contain site preparation instructions between the CPU board and integral printer. for a line leak detector.Since much of the site preparation • Remote Display Interface Module.Required for for a line leak detector will be performed concurrently interface to a Veeder-Root Remote Display. with the site preparation for the rest ofthe system,be sure • Remote Printer Interface Module.Provides a 25- to consider its requirements at all times. pin male D-connector for data transmission to a remote serial printer. If installing line leak detectors with this system,be sure • SiteFax Fax/Modem Module.A 2400-baud inter- to refer to Manual Number 576013-764 for site prepara- nal modem and a 9600-baud facsimile with twin tion and installation instructions. snap-in jacks for direct data transmission over phone lines. A. PROBE RISER PIPE INSTALLATION. B. PROBES. (See Figure 4, "Capacitance Probe Installation Require- ments," and Figure 5, "Magnetostrictive Probe Installa- The TLS-350 can accommodate Veeder-Root capacitance tion Requirements.") and magnetostrictive probes.The installation and wiring procedures for these probes are described in this manual. IMPORTANT:For maximum height-to-volume accuracy, select the threaded hole closest to the middle of the tank C. SENSORS. and install a 4-inch riser pipe (ANSI pipe, sch. 40). A TIS-350 system can incorporate sensors that detect Standard procedures for installing a fill pipe can be used. liquids in interstitial spaces of double-wall tanks and piping Instructions are based on a 4-inch riser pipe,however,the sumps of double-wall piping, detect hydrocarbon liquids capacitance probes will also fit a 3-inch riser. and vapors in monitoring wells, and detect liquids and hydrocarbons in dispenser pans and containment sumps. 1. If the tank is buried,excavate the portion of the tank Interstitial,piping sump and hydrostatic sensors are two- that contains the riser hole. wire devices;while vapor and groundwater sensors, and 2. Remove the bung from the hole and install the riser containment sump and the dispenser pan sensors are pipe. three-wire devices. The installation and wiring proce- dures for these sensors are described in this manual. NOTE:The top of the riser pipe must be threaded to accept a 4 x 8 NPT cap adaptor ring. D. LINE LEAK DETECTORS. The TLS-350 system can include up to eight line leak detectors monitoring one line per detector, and each detector requires one Line Leak Detector Module in- M:NiMUM OIA stalled in the monitor. Site preparation and installation OLE instructions for the Veeder-Root Line Leak Detector are 3R "C ' TE SLAB CAEO EAR*� ?CORD GRIP SEALS PER NFPA 9p SUPPLIED WITH PROBE contained in Manual Number 576013-764. E. REMOTE DISPLAY. STRAIN WEN TIIONHERPROOF RELIEF v u CBOx wlfn The TLS-350 system can interface to a Veeder-Root Re- `""'"— �'C`ICINCA, 6 CUBIC mote Display. Site preparation and installation instruc- EE X. M SEAL tions for the Remote Display are contained in Manual EC A Number 576013-811. -NOE;E SUF�IE-11. R15EA DIMENSION PROBE SHOULD BE XITO THE BOTTOM OF +00 AP I PIPE SECTION 3. SITE PREPARATION HE RISER CAP SCHED-E. WARNING: IN INSTALLATION OF THIS PRODUCT, COMPLY WITH THE NATIONAL ELECTRICAL CODE;FEDERAL,STATE AND LOCAL CODES; AND OTHER APPLICABLE ""'""`E BE SAFETY CODES. WARNING: TO PROTECT YOURSELF AND OTHERS FROM BEING STRUCK BY VE- HICLES DURING WORK,BLOCK OFF YOUR WORK AREA DURING INSTALLATION OR SERVICE. nn,nr wrI PIP,,,— FAILURE IP,,,— FAILURE TO COMPLY WITH THESE WARN- . ne rP,mPm,PP,Pe.rPPP.,P.rPPmI INGS COULD RESULT IN DEATH, SERIOUS PERSONAL INJURY,PROPERTY LOSS,AND EQUIPMENT DAMAGE. Figure 4. Capacitance Probe Installation Requirements. 5