Laserfiche WebLink
Site Preparation d Installation Instructions V <br /> TLS-350 UST Monitoring System -'� <br /> i <br /> ll� l" <br /> �y MAGNET / BALLAST RING <br /> N TOP f <br /> I ((LYS (IF REQUIRED) <br /> / BOOT <br /> MAGNET <br /> EL FLOAT IN TOP <br /> t..- :.3SEMBLY WATER FLOAT <br /> ASSEMBLY <br /> 3 AD.'. <br /> HIN <br /> Figure 34. Probe Assembly for Products Requiring <br /> Water Measurement(4"Installation Kit) <br /> Figure 33. 3"Probe Riser Adaptor Ring Installation <br /> BALLAST RING . <br /> 3. Press the adaptor onto the canister until the locking (IF REQUIRED) MAGNET <br /> tabs are on the flats. Twist the adaptor until the tabs IN TOP <br /> are on the diameter of the canister and slide the BOAT I \• <br /> adaptor to the bottom of the canister. <br /> 4. Once the adaptor is at the bottom of the canister,twist <br /> the adaptor until its locking tabs snap into the locking <br /> grooves. FUEL FLOAT <br /> ASSEMBLY <br /> 5. Place the second adaptor on top of the probe canister MAGNET <br /> with its bevelled edge up and its locking tabs aligned WATER FLOAT N TOP <br /> ASSEMBLY <br /> with the flats on the canister. <br /> 6. Press the adaptor onto the canister until the locking Figure 35. Probe Assembly for Products Requiring <br /> tabs are on the flats.Twist the adaptor until its locking <br /> Water Measurement(2"Installation Kit) <br /> tabs snap into the locking grooves. <br /> Ballast RingD2—used with:jet fuel,kerosene,diesel#2. <br /> D.FLOAT ASSEMBLIES The following liquids do not use a water float,as water is <br /> not measurable in the liquid:ethylene glycol(antifreeze), <br /> ]MPORTANT! propylene glycol (antifreeze), wastewater, windshield <br /> When installing a high alcohol magnetostrictive washer fluid, used oil, fuel oil #4 with specific gravity <br /> probe,Form No.8473XX-4XX or 8473XX-5XX,note greater than 0.925. <br /> the following. ,� NOTE:Only the water float mounting tube will be <br /> The Magnetostrictive Probe Installation Kit for use used in place of the water float assembly for the <br /> with high alcohol probes, Form No. 8496XX-XX4, products where water measurement is not possible. <br /> does not contain a water float.Adding a water float (See Figure 36). <br /> or sinker in this application will cause equipment to 3. Gently slide the fuel float onto the probe shaft, <br /> malfunction.A float kit containing only a fuel float magnet-side up. The float should move freely on the <br /> must be used with this probe. probe shaft.(See Figure 34 or 35,"Probe Assembly for <br /> Products Requiring Water Measurement," or Figure <br /> l. Remove the fuel float and water float from the Magnetos- 36,"Probe Assembly for Products NOT Requiring Wa- <br /> ter Measurement"). <br /> trictive Probe Installation Kit box(refer to Figure 30 or 31). <br /> 2. Ballast ringsare facto installed on the water float of NOTE: The fuel float must be placed magnet-side <br /> �y- up to effectively measure fuel.The magnet is located <br /> magnetostrictive probes to ensure proper float action. in the narrow cylindrical end of the fuel float. The <br /> The ringtype varies with the fluid being measured.Float wider end of the float is marked "BOTTOM THIS <br /> ballast rings are available for the following liquids: SIDE DOWN". <br /> 1p <br /> Ballast Ring G2 — used with: aviation gas, regular BE SURE TO SLIDE THE MAGNET END OF THE <br /> unleaded gasoline,premium unleaded gasoline,leaded FLOAT ON FIRST! <br /> gasoline,gasohol. NOTE: When using 2" floats,be sure to choose 2" <br /> Ballast Ring L2 —used with: motor oil, toluene, gear oil float duringIn-Tank Setup.Refer to TLS-350"Setup <br /> Instructions,"Manual No. 676013-623. <br /> 90W,transmission fluid. <br /> 25 <br />