COMPLIANCE INFO_1996 - 2004 - Laserfiche WebLink

Home Browse Search

FVEEDER-ROOT SUMP S SOR INSTALLATION INSTRUIc iTONS IMPORTANT! THIS MANUAL REQUIRES ALL PRELIMINARY SITE PREPARATIONIS COMPLETED,AND THAT FIELD WIRING FROM THE MONITOR TO THE SENSOR JUNCTION BOX IS IN PLACE. IT CONTAINS INSTALLATION AND WIRING PROCEDURES FOR THE INSTALLATION OR REPLACEMENT OF A SUMP SENSOR SWITCH ONLY! FOR NEW INSTALLATIONS, REFER TO THE APPLICABLE "SITE PREPARATION AND INSTALLATION INSTRUCTIONS" MANUAL PROVIDED WITH THE SYSTEM AND LISTED IN SECTION I.A.1 OF THIS MANUAL. SECTION 1. INTRODUCTION damage caused by improper packing. Address the shipment to Veeder-Root Co., 6th Avenue at Burns Crossing, Altoona, A. GENERAL Pennsylvania 16603. 1. This manual contains installation procedures for the installation or replacement of Veeder-Root Sump Sensor, Part SECTION II. PIPING SUMP SENSOR No. 794390-205, any of the following monitoring systems INSTALLATION designed and manufactured by Veeder-Root Company:ILS-250, The sum sensor comes with the following hardware necessary TLS-2501, TLS-3001, TLS-350 or TLS-350R System. P g rY to mount it within the piping sump: This manual assumes all preliminary site preparation is com- pleted, and that field wiring from the monitor to the sensor 1 - PVC Mounting Sleeve junction box is in place. 1 - Aluminum 90° Mounting Bracket 1 - Cord Grip If site preparation is necessary,refer to the appropriate Veeder- 2 - #6-20 (.312" long) Sheet Metal Screws Root Site Preparation and Installation Instructions: ILS-250, Manual No.576013-727;TLS-250i Four-Tank(Direct-Connect) A. GENERAL The sump sensor can be mounted either of two System,Manual No.576013-579;TLS-250iEight-Tank(Indirect- ways: on the sensor junction box using the mounting bracket Connect) System, Manual No. 576013-577; TLS-3001, Manual and sleeve supplied (Figure 1); or, by cementing the PVC No. 576013-275; ILS-350, Manual No. 576013-773; TLS-350, mounting sleeve directly to the side of a fiberglass containment Manual No.576013-622;TLS-350R,Manual No.576013-879;or sump (Figure 4). contact your Veeder-Root representative for assistance. Before you install the sump sensor, there are several important 2. When a vertical bar I appears adjacent to text or illustra- requirements to consider: tions, information has been added or changed at the last 1. The sump sensor must be positioned as close to the revision date. containment sump outer wall as possible. B. DAMAGE CLAIMS 2. The sump sensor must be mounted in a true vertical position 1. Thoroughly examine all components and units as soon as to ensure proper operation of the float switch contained inside. received. If damaged,write a complete and detailed description of the damage on the face of the freight bill. Have the carrier's 3. There must be at least one inch of clearance between the agent sign the description. bottom of the mounting sleeve and the base of the sump. NOTE: Insist that the carrier's agent verify the 4. When installed, the sump sensor must rest on the base of the inspection and sign the description. sump. B. INSTALLATION. The wires between the monitor or ESA 2. Immediately notify the delivering carrier of damage or loss. module and each sump sensor location must be of a type This notification may be given either in person or by telephone. designed for use in the presence of gasoline and oil, and must Written confirmation must be mailed within 48 hours. Rail- be between AWG 14 and AWG 18. The conduit must be roads and motor carriers are understandably reluctant to make properly sealed in accordance with the National Electrical Code adjustments for damaged merchandise unless inspected and (NFPA 70) and the Automotive and Marine Service Station reported promptly. Code (NFPA 30A)since they pass from a Class I,Division I or Division II area into a nonhazardous area. 3. Risk of loss, or damage to merchandise remains with the buyer. It is the buyer's responsibility to file a claim with the carrier involved. -tts WARNING: TO AVOID ELECTRICAL 4. Immediately advise your Veeder-Root representative, SHOCK WHICH COULD KILL YOU, BE distributor,or the factory so that we may assist you. SURE AC POWER TO THE MONITOR ISOFF DURING INSTALLATION. C. RETURN SHIPPING. All shipments of Veeder-Root products must be prepaid. If the sump sensor is damaged, return it in the original shipping container with shock absorbing material provided. Veeder-Root will accept no liability for 2